Olympia electronics EASY LIGHT Series Manuel utilisateur

GR-312/15L

220-240V AC/50-60Hz

IP 40

3,6V/1,5Ah

105lm

EN 60598-1, EN 60598-2-22, EN 55015, EN 61547, EN 61000-3-2, EN 61000-3-3

735gr.

3,6V/600mAh

3W /3VA

655gr.

GR-310/15L

Thank you for purchasing this product of

Olympia Electronics. A European manufacturer.

GENERAL

These luminaires are used indoors (ta 40 C)

where emergency light is needed.

Each luminaire must be permanently connected

to mains power supply.

In normal operation the battery is charging and

the 2 yellow LED’s light in the screen.

In case of a mains power supply failure the

luminaire will light the led strip automatically in

emergency mode. When the mains power

supply is restored the device turns to normal

operation.

MAINTAINED / NON-MAINTAINED

OPERATION

There is an option to select the maintained or

non-maintained operation by placing the jumper

to the appropriate place according to step 8

(page 4).

INSTALLATION

To install the luminaire follow the installation

instructions οn page 4.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance or

testing must be done by authorized personel

only.

2. The device must be connected to the mains

power supply thru a fuse dependent by the total

amount of the line’s power load.

3. It is sugested to check every month the

indication LED for battery charging, and by

pu s h i n g t h e T ES T b u t to n t o c h e ck t h e

emergency circuit. The led strip should: a) light

with bigger intensity as long as the TEST button

is pressed (maintained operation),

b) light as long as the TEST button is pressed

(non-maintained operation).

4. It is sugested to check every 6 months the

minimum autononous duration by disconnecting

the mains power supply. Count the time that the

led strip lights and in case of less time than the

minimum autonomous duration the battery must

b e r e p l a c e d . I f t h e m e a s u r e d t i m e i s

considerably less than the minimum autonomous

duration In case of battery

or led strip replacement, these must be replaced

by parts of the same type, by the manufacturer

or by a competent person.

t i

in battery recycling

points. Do not incinerate.

If the luminaire

doesn’t work as described above contact the

installer.

contact the installer.

5. In case of inactive use for a period greater

than 2 months, disconnect the battery by pulling

out the battery’s connector.

6. I s not allowed to discard batteries in to

common tr ash bins, t hey must b e

discarded only

TECHNICAL CHARACTERISTICS

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERIES (Ni-Cd)

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

ILLUMINATION SOURCE

24h

From overcharge and full discharge

15 white LED’s

Bayblend FR3010, transparent polycarbonate

180min

0 to 40 C

Up to 95%

3 years (1 year for the battery)

90min

Page 1 from 4

Battery charging LED, TEST button

‘’EASY LIGHT‘’ SERIES FOR NON-MAINTAINED/ΜΑΙΝΤΑΙΝΕD

EMERGENCY LUMINAIRES

350 x 134 x 45 mm (CRV 362 x 134 x 58 mm)

923312017_09_003

High Quality European based Manufacturers

Page 2 from 4 923312017_09_003

Installation methods

A-3018

Special mounting

springs for

suspended ceiling

installation

Mounting springs Α-3018

Wall or ceiling installation

Suspended ceiling installation

Wall installation with SP-114

marking panel

A-3018

SP-114 marking panel

Suspended ceiling installation

with Α-3018 mounting springs

and SP-114 marking panel

Recess mounting

base Α-3016

Recess mounting in a wall Ceiling installation

with SP-114 marking panel

MARKING PANEL SP-114

A marking panel SP-114 can be installed on the

luminaire in 3 different locations. This marking

panel is installed perpendicular to the diffusor of

the luminaire, as shown in the pictures below.

The panel is pre-printed and has a plastic

accessory on each side that is used to fasten the

panel to the luminaires.

There are 2 arrow stickers that can be placed in

each side of the marking panel to point to the

desired direction.

Placing the SP-114 marking panel

Place the plastic mounting accessories of the

marking panel as shown in pictures.

ΝΟΤΕ!! This marking panel (SP type) can not

be installed on CRV luminaires.

Page 3 from 4

Suspended ceiling

Α-3018 mounting springs

PLACING Α-CRV PARTS

To install the curve crystal Α-CRV you must first install the

included plastic extension to mount it on the TEST button.

Mounting methods

All “Easy Light” can be mounted either surface or recess

mounted in walls or suspended ceilings. For recess

mounted installations, special accessories are required

which can be found in the catalog and must be ordered

separately.

Suspended ceiling installation.

On the bottom of the base plastic of the Easy light

luminaire there are two H shaped cut outs. These are

used to install the A-3018 mounting springs.

1. With a sharp tool remove the appropriate plastic

pieces to fit the mounting springs. First place the edges

of the mounting spring to the respective holes and install

the one end of the coil to the support axis.

2. Install the other end of the coil to the other support

axis.

3. Bend the springs and place the luminaire to the

respective suspended ceiling’s hole.

The luminaire’s placement to the suspended ceiling

must be done after the connection with power supply

cables.

Recess mounting in a wall

The special mounting base (A-3016) can be built in the

wall and on it can be mounted the luminaire with the Α-

3016 included screws, following the installation

instructions of the luminaire. The mounting base

contains pre-etched holes for cable entry that are

aligned with the cable entry holes of the luminaire.

Bottom view of a wall

Α-3016 recess

mounting base

Mounting Easy Light luminaire

in a suspended ceiling

Recess mounting for an ‘’Easy Light”

luminaire in a wall.

Required

opening in

a suspended

ceiling

340

124

923312017_09_003

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

0: Non Maintained (*)

A: Including test device

*90: 1.5 hour duration

180: 3 hour duration

(*) Non-Maintained operation: The luminaire lights its illumination source, only in power supply’s

failure.

Maintained operation: The luminaire lights its illumination source, when it is powered by the mains

power supply or not.

Page 4 from 4

INSTALLATION INSTRUCTIONS

Diffusor

Reflector

Base plastic

923312017_09_003

8. MAINTAINED/NON-MAINTAINED OPERATION

JUMPER SELECTION

You can choose the luminaire’s operation.

When the jumper is installed (by default) on the middle and left

pins you select non-maintained operation. When the

jumper is installed on the middle and right pins you select

maintained operation.

NOTE!! After finishing the installation you must power the

device at least for 24 hours for battery charging to perform the

named autonomy.

5 6

1 To install the luminaire you must dismantle it to 3 parts.

2 Place a flat blade screwdriver in the area Α to release the diffusor’s plastic hook.

3 Place a flat blade screwdriver in the area B to release the reflector’s plastic hook.

4 Use the included mounting parts to mount the base plastic. Pass the mains cable thru a cable

entry channel and secure it with a suitable bracket to ensure immobilization of the cable at a

distance of no more than 5cm from the luminaire’s cable entry.

5 Place the battery’s connector to the corresponding connector on the P.C.B.

6 Connect the mains cables to the respective detachable terminal block. Ν for neutral and L for

live wire.

7 Refit the removed parts in steps 2 and 3 (mind the correct orientation) and the luminaire is ready

to operate.

Non-maintained

operation

Maintained

operation

Base plastic

Cable entry channels

Luminaire mounting holes

Cable

support

Battery replacement.

It can be done only by a competent person and after the mains interruption.

1. Follow the step 2 and 3 of the installation procedure.

2. Disconnect the connector and remove the old battery.

3. Connect the new battery with the same type (step 5 of the installation procedure) and place it in

the position of the old one.

4. Follow the step 7 of the installation procedure and power the device.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels olympia electronics Lanterne

olympia electronics

olympia electronics GR-579/L/90/WP Manuel utilisateur

olympia electronics

olympia electronics KLIN-20/ST/ADR Manuel utilisateur

olympia electronics

olympia electronics SLIM LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-220/DUO/M Manuel utilisateur

olympia electronics

olympia electronics GR-939/30L/LT Manuel utilisateur

olympia electronics

olympia electronics GR-940/15L/MAR Manuel utilisateur

olympia electronics

olympia electronics Slim Light Series Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics GR-290/WP Manuel utilisateur

olympia electronics

olympia electronics OLY-1024/WL Manuel utilisateur

olympia electronics

olympia electronics POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-427/12L Manuel utilisateur

olympia electronics

olympia electronics LLB-26/90 Manuel utilisateur

olympia electronics

olympia electronics GR-427/12L/MAR Manuel utilisateur

olympia electronics

olympia electronics WEATHER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-1935/15L Manuel utilisateur

olympia electronics

olympia electronics GR-2100/ST Manuel utilisateur

olympia electronics

olympia electronics GR-490/ADR Manuel utilisateur

olympia electronics

olympia electronics POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics Classic Light Series Manuel utilisateur

olympia electronics

olympia electronics OLY-1004 Manuel utilisateur

olympia electronics

olympia electronics CLASSIC LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics BAU LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-108/12L/90 Manuel utilisateur

Manuels Lanterne populaires d'autres marques

KYOWA

KYOWA KW-9114 Manuel utilisateur

Stahl

Stahl ECOLUX 6610 Series Manuel utilisateur

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuel utilisateur

PRG

PRG VARI LITE VL5 Manuel utilisateur

Raytec

Raytec VARIO2 series Manuel utilisateur

ENSA

ENSA LEDBT18WS2 Manuel utilisateur

LUG

LUG OFFICE LB LED N/T Manuel utilisateur

GE Wallighter 250 Manuel utilisateur

Draper

Draper RLEDL19/B Manuel utilisateur

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuel utilisateur

Panasonic

Panasonic EY3741B57 Manuel utilisateur

Clas Ohlson

Clas Ohlson LCC8T Manuel utilisateur

Coolon

Coolon WDN-140 Manuel utilisateur

Holiday Travel

Holiday Travel 834873 Manuel utilisateur

BEGA

BEGA 84 036 Manuel utilisateur

BEGA

BEGA 33 596 Manuel utilisateur

Dale Tiffany

Dale Tiffany GT701162 Manuel utilisateur

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuel utilisateur

olympia electronics EASY LIGHT Series Manuel utilisateur

Manuels Lanterne populaires d'autres marques