Olympia electronics GR-290/WP Manuel utilisateur

Page 1 from 5

GENERAL

These devices are used indoors (ta 40 C) in

places where emergency luminaires are

needed. The luminaires GR-290/WP and GR-

292/WP are suitable for corridors lighting and

the GR-291/WP and GR-293/WP for open

a r e a l i g h t i n g . E a c h d e v i c e m u s t b e

permanently connected to mains power

supply. In normal operation the battery is

charging. In case of a mains power supply

failure the device will light the illumination

led automatically in emergency mode. When

the mains power supply is restored the

device turns to normal operation.

INSTALLATION

To install the luminaire follow the installation

instructions οn page 2.

Battery Charging

The battery charging is completely controlled.

In this case, is achieved the perfect battery

maintenance , as well as the elongation of its

duration. When the battery has completely

charged, it charges with a maintenance

current.

Battery Cut-off

The device in this operation when the mains

power supply fails and battery has lost its

energy. During this operation the device

enters the idle state and battery consumption

is negligible, in order to be protected from

deep discharge.

Automatic Operational Test

It is conducted automatically every 15 days. In

order to be performed, the mains power

supply and the battery should be connected.

Automatic Autonomous Test

The Automatic Autonomous Test is conducted

and measures the device’s back up operation

and emergency duration. The BATTERY

FAULT LED blinks during the measurement,

indicating this process to the user. This test is

conducted automatically every six months. In

order to be performed, the mains power

supply and the battery should be connected

and fully charged. If the battery is not fully

charged, the test is postponed until the battery

is completely charged. If during this test, the

autonomy is less than the nominal then the

battery fault led turned on continuously and

the battery must be replaced.

Back Up Operation

The autonomous duration of battery during

emergency mode is at least the one that is

WATERPROOF SELF TESTING NON MAINTAINED SPOT LIGHT

EMERGENCY LUMINAIRES WITH 1 WHITE POWER LED

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

CONSTRUCTION MATERIAL

EXTERNAL DIMENSION

WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERY (Ni-MH)

CHARGE TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

LIGHT SOURCE

220-240V AC / 50-60Hz

3 hours1.5 hour

24 hours

Deep discharge and overcharge protection

IP65

4.8V/1.2Ah

270lm 160lm

1 white power LED

5 to 40 C

Up to 95%

ABS/PC, PC

3 years (1 year for the battery)

430gr.

Ø125 x 65 mm

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

Charge, lamp fault, battery fault, TEST button

GR-290/WP GR-291/WP GR-292/WP GR-293/WP

3.7W / 4.1 VA

TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)

Thank you for your trust in our products

Olympia Electronics - European manufacturer

923293005_09_004

Page 2 from 5

stated in the list of the technical

characteristics. During emergency mode, a

light source test is also performed.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance

or testing must be done by authorized

personnel only.

2. The device must be connected to the

ma i n s p o we r s up p l y t h roug h a fu s e

dependent by the total amount of the line’s

power load.

3. The replacement of the battery and the

light source must be done using parts of the

same type, by the manufacturer or by a

competent person.

4. In case of inactive use for a period greater

than 2 months, disconnect the battery by

pulling out the battery’s connector.

5. I s not allowed to discard batteries t i

into common trash bins, they must

b e d i s c a r d e d o n l y i n b a t t e r y

recycling points. Do not incinerate.

The light source contained in this

luminaire shall only be replaced by the

manufacturer, or his agent, or a similar

qualified person.

NOTE! The light source is non-user

replaceable.

Initial installation

1 Untighten the screw and pull up the reflector.

2 Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type 2x1mm²

or any other type, at least equal to it’s mechanical and electrical properties). ATTENTION!!

The cable must not be deformed in any way (This requirement is important to ensure the ΙΡ

rating). Install the included gaskets in to the cable entry holes (verify that are not deformed). Make a

hole in the center by using a small screwdriver. Pass the round cable through the gasket. Detach the

power terminal, connect the wires as shown in the picture and attach the power terminal (10A max).

3 Place the battery’s connector to the corresponding connector on the P.C.B.

4 Refit the reflector (mind the correct orientation), tighten the screw securely and the luminaire is ready

for mounting.

NOTE!! After finishing the installation you must power the luminaire for, at least, 24 hours for

battery charging to perform the nominal autonomy.

Cable

entry

hole L

INSTALLATION INSTRUCTIONS

923293005_09_004

Page 3 from 5

Set up the lamp to the suspended ceiling as it is shown bellow (Required opening 110mm):

Step 1

Bend the springs, to get into the hole of the suspended ceiling, as you can see to the next figure.

Step 2

Push up the luminaire, as shown in figure 2.

Step 3

Continue to push upwards until the lamp locks.

If you want to pull off the device, put a flat blade

screwdriver, between the device and the ceiling.

Figure 2

Figure 3

Figure 1

Ø110mm

Step 1. Follow the step 1 of the installation instructions.

Step 2. Unfasten the retaining screw (Figure 4) and detach the part for suspended ceiling

installation.

Step 3. Drill 2 holes on the base using a 4mm drill bit in order to permit the retaining screws to pass.

Mark these two drilled points on the required mounting location, drill the holes and install the supplied

plastic plugs. ATTENTION!! Especially for the GR-290/WP and GR-292/WP luminaires installation on

the ceiling you must align the base with the indications on the luminaire’s base (Figure 5).

Step 4. WARNING!! To preserve the ΙΡ 65 rating, fit the screws with the metallic washer and

plastic ring which are included. Next use the screw to fasten the unit to the surface .(Figure 6)

Step 5. Install the decorative rim (package included). Next, use the 2 fasteners to install the unit to

the require location.

Step 5. Follow the step 3 of the installation instructions.

Figure 6

SURFACE MOUNTING

MOUNTING THE LAMP IN SUSPENDED CEILING

Figure 4 Figure 5

Retaining fastener

Drill here

Indications

923293005_09_004

Page 4 from 5

Lamp fault

indication LED

GR-290/WP, GR-292/WP

GR-291/WP, GR-293/WP

ATTENTION!!!

During installation follow this light direction.

Corridor

lighting

Open

area

lighting

Important notice for the installed luminaires in one area !!!

The installer must connect the battery’s connector first and then should power the luminaire.

The time between batteries connection must be, at least 1.5 minute.

With this variation, it is ensured that the non synchronized Automatic Autonomous Test for

two or more luminaires installed in one area, is not conducted in the same day.

Battery replacement.

It can be done only by a competent person and after the mains interruption.

1. Remove the luminaire from the suspended ceiling (figure 3).

2. Follow the step 1 of the installation instructions.

3. Disconnect the connector and remove the old battery.

4. Connect the new battery with the same type (step 2 of the installation instructions) and place it in

the position of the old one.

5. Replace the removed parts (step 1 and 4) and power the device.

FAULT

LAMP

CHARGE

BATT.

FAULT

LAMP

CHARGE

BATT.

125

FAULT

LAMP

CHARGE

BATT.

FAULT

LAMP

CHARGE

BATT.

Battery

fault

indication

LED

Battery

charge

indication

LED

Figure 4

LED MODULE CHARACTERISTICS

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

Olympia Electronics S.A

60 °C max. across the board 45 °C max. across the board

Non reversible connection between main pcb and led module

3-3.2VDC

2.2W 1.1W

1110143 2704143

GR-290/WP

GR-291/WP

GR-292/WP

GR-293/WP

Status of LEDs

LEDs Description of indication

CHARGE : Battery charging, : battery charged, : disconnected or unfunctional battery

LAMP FAULT : Operation check, : lamp fault, : normal operation

BATT. FAULT : Autonomy test, : battery fault, : normal operation

Note : Blinking, : constantly on, : off

CAUTION : Do not view directly with bare eyes.

923293005_09_004

TEST

FAULT

LAMPCHARGE BATT.

Page 5 from 5

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

0: Non maintained (*)

A: Including test device

90: 1.5 hour duration

180: 3 hours duration

(*) Non Maintained operation: The luminaire lights its illumination source, only in power

supply’s failure.

Maintained operation: The luminaire lights its illumination source, when it is powered by the

mains power supply or not.

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty

is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which

accompanies each product. This warranty ceases to exist if the buyer does not follow the technical

instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods

provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully

agreed to them in writing. Products that have been damaged can be returned to the premises of our

company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the

buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the

buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

923293005_09_004

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels olympia electronics Lanterne

olympia electronics

olympia electronics SLIM LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics Double Easy Light GR-391/L Manuel utilisateur

olympia electronics

olympia electronics POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-900/30L/SC Manuel utilisateur

olympia electronics

olympia electronics GR-796/ST/DUO/ADR Manuel utilisateur

olympia electronics

olympia electronics GR-490/ADR Manuel utilisateur

olympia electronics

olympia electronics GR-292/M/HL Manuel utilisateur

olympia electronics

olympia electronics GR-108/12L/90 Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics GR-220/DUO/M Manuel utilisateur

olympia electronics

olympia electronics OLY-1004/WP/ADR Manuel utilisateur

olympia electronics

olympia electronics GR-1935/15L Manuel utilisateur

olympia electronics

olympia electronics GRL-37/90/ADR Manuel utilisateur

olympia electronics

olympia electronics OLY-500 Manuel utilisateur

olympia electronics

olympia electronics GR-490/WP/ADR Manuel utilisateur

olympia electronics

olympia electronics Power Light Series Manuel de l'opérateur

olympia electronics

olympia electronics GR-427/12L Manuel utilisateur

olympia electronics

olympia electronics WEATHER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics BAU LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-2100/ST Manuel utilisateur

olympia electronics

olympia electronics CLASSIC LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-427/12L/MAR Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

Manuels Lanterne populaires d'autres marques

KYOWA

KYOWA KW-9114 Manuel utilisateur

Stahl

Stahl ECOLUX 6610 Series Manuel utilisateur

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuel utilisateur

PRG

PRG VARI LITE VL5 Manuel utilisateur

Raytec

Raytec VARIO2 series Manuel utilisateur

ENSA

ENSA LEDBT18WS2 Manuel utilisateur

LUG

LUG OFFICE LB LED N/T Manuel utilisateur

GE Wallighter 250 Manuel utilisateur

Draper

Draper RLEDL19/B Manuel utilisateur

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuel utilisateur

Panasonic

Panasonic EY3741B57 Manuel utilisateur

Clas Ohlson

Clas Ohlson LCC8T Manuel utilisateur

Coolon

Coolon WDN-140 Manuel utilisateur

Holiday Travel

Holiday Travel 834873 Manuel utilisateur

BEGA

BEGA 84 036 Manuel utilisateur

BEGA

BEGA 33 596 Manuel utilisateur

Dale Tiffany

Dale Tiffany GT701162 Manuel utilisateur

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuel utilisateur

olympia electronics GR-290/WP Manuel utilisateur

Manuels Lanterne populaires d'autres marques