Olympia electronics GR-270 Manuel utilisateur

Page 1 from 4923270000_09_004

GENERAL

These devices are used indoors (ta 40 C)

in places where emergency luminaires are

needed. The luminaires GR-270 and GR-

272 are suitable for corridors lighting and

the GR-271 and GR-273 for open area

lighting. Each device must be permanently

connected to mains power supply. In

normal operation the battery is charging. In

case of a mains power supply failure the

device will light the illumination led

automatically in emergency mode. When

the mains power supply is restored the

device turns to normal operation.

INSTALLATION

To install the luminaire follow the

installation instructions οn page 2.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance

or testing must be done by authorized

personel only.

2. The device must be connected to the

mains power supply thru a fuse dependent

by the total amount of the line’s power

load.

3. It is sugested to check every month the

indication LED for battery charging, and by

pushing the TEST button (use a pointy tool

with diameter of 2mm max.) to check the

emergency cirquit. The illumination LED

should light as long as the TEST button is

pressed. In the opposite condition contact

the installer.

4. It is sugested to check every 6 months

the minimum autononous duration by

disconnecting the mains power supply.

Count the time that the luminaire lights and

in case of less time than the minimum

autonomous duration the battery must be

r e p l a c e d . I f t h e m e a s u r e d t i m e i s

considerably less than the minimum

autonomous duration contact the installer.

I n c a s e o f b a t t e r y o r l i g h t s o u r c e

replacement, these must be replaced by

parts of the same type, by the manufacturer

or by a competent person.

5. In case of inactive use for a period

greater than 2 months, disconnect the

batt ery by pulli ng out the ba ttery ’s

connector.

6. I s not allowed to discard batteries in t i

to common trash bins, they must be

discarded only in battery recycling

points. Do not incinerate.

NON MAINTAINED SPOT LIGHT EMERGENCY

LUMINAIRES WITH 1 WHITE POWER LED

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

CONSTRUCTION MATERIAL

EXTERNAL DIMENSION

WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERY (Ni-MH)

CHARGE TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

LIGHT SOURCE

220-240V AC / 50-60Hz

3 hours1.5 hour

24 hours

Deep discharge and overcharge protection

IP40

3.6V/1.5Ah

160lm 120lm

1 white power LED

5 to 40 C

Up to 95%

ABS/PC, PC

3 years (1 year for the battery)

380gr.

Ø125 x 65 mm

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

Charge, TEST button

GR-270 GR-271 GR-272 GR-273

2.4W / 2.7VA

TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)

Thank you for your trust in our products

Olympia Electronics - European manufacturer

Page 2 from 4

The light source contained in this luminaire shall only be replaced by the

manufacturer, or his agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

INSTALLATION INSTRUCTIONS

Initial installation

1 Untighten the screw and pull up the reflector.

2 Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type 2x1mm²

or any other type, at least equal to it’s mechanical and electrical properties). ATTENTION!!

The cable must not be deformed in any way (This requirement is important to ensure the ΙΡ

rating). Install the included gaskets in to the cable entry holes (verify that are not deformed). Make a

hole in the center by using a small screwdriver. Pass the round cable through the gasket. Detach the

power terminal, connect the wires as shown in the picture and attach the power terminal (10A max).

3 Place the battery’s connector to the corresponding connector on the P.C.B.

4 Refit the reflector (mind the correct orientation), tighten the screw securely and the luminaire

is ready for mounting.

NOTE!! After finishing the installation you must power the luminaire for, at least, 24 hours for

battery charging to perform the nominal autonomy.

GR-270, GR-272

GR-271, GR-273

ATTENTION!!!

During installation follow this light direction.

Corridor

lighting

Open

area

lighting

CHARGE TEST

CHARGE TEST CHARGE TEST

125

CHARGE TEST

Battery

charge

indication

LED

Figure 4

Test

button

923270000_09_004

Cable

entry

hole

Page 3 from 4

Mounting the lamp in suspended ceiling.

Set up the lamp to the suspended ceiling as it is shown bellow (Required opening 110mm):

Step 1

Bend the springs, to get into the hole of the suspended ceiling, as you can see to the next figure.

Step 2

Push up the luminaire, as shown in figure 2.

Step 3

Continue to push upwards until the lamp locks.

If you want to pull off the device, put a flat blade

screwdriver, between the device and the ceiling.

Figure 2

Figure 3

Figure 1

Ø110mm

923270000_09_004

Surface mounting

Install the luminaire according to the following steps:

Step 1. Follow the step 1 of the installation instructions.

Step 2. Unfasten the retaining screw (Figure 4) and detach the part for suspended ceiling installation.

Step 3. (Figure )Drill 2 holes on the base 5 using a 4mm drill bit in order to permit the retaining screws to

pass. Mark these two drilled points on the required mounting location, drill the holes and install

the supplied plastic plugs. ATTENTION!! Especially for the GR-270 and GR-272 luminaire

installation on the ceiling you must align the base with the indications on the luminaire’s base.

Step 4. Install the decorative rim (package included). Next, use the 2 fasteners to install the unit to the

require location.

Step 5. Follow the steps 2,3 and 4 of the installation instructions.

Figure 4 Figure 5

Retaining fastener

Drill here

Indications

Page 4 from 4

Battery replacement.

It can be done only by a competent person and after the mains interruption.

1. Remove the luminaire from the suspended ceiling (figure 3).

2. Follow the step 1 of the installation instructions.

3. Disconnect the connector and remove the old battery.

4. Connect the new battery with the same type (step 2 of the installation instructions) and place it in

the position of the old one.

5. Replace the removed parts (step 1 and 4) and power the device.

LED MODULE CHARACTERISTICS

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

Olympia Electronics S.A

60 °C max. across the board 45 °C max. across the board

Non reversible connection between main pcb and led module

5.8-6.2V DC

1.3W 1W

1903175

GR-270

GR-271

GR-272

GR-273

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of

warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,

which accompanies each product. This warranty ceases to exist if the buyer does not follow the

technical instructions included in official documents given by Olympia Electronics or if the buyer

modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia

Electronics has fully agreed to them in writing. Products that have been damaged can be returned to

the premises of our company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge

the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or

not the buyer the transportation cost.

HEAD OFFICE

72nd km. Ο.N.R. Thessaloniki-Κaterini

P.C. 60300 P.O. Box 06 Eginio Pierias Greece

www.olympia-electronics.gr

[email protected]

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

0: Non maintained (*)

A: Including test device

90: 1.5 hour duration

180: 3 hours duration

(*) Non Maintained operation: The luminaire lights its illumination source, only in power

supply’s failure.

Maintained operation: The luminaire lights its illumination source, when it is powered by the

mains power supply or not.

923270000_09_004

CAUTION : Do not view directly with bare eyes.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels olympia electronics Lanterne

olympia electronics

olympia electronics GR-220/DUO/M Manuel utilisateur

olympia electronics

olympia electronics GRL-37/90/ADR Manuel utilisateur

olympia electronics

olympia electronics GR-292/M/HL Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics WEATHER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-900/30L/SC Manuel utilisateur

olympia electronics

olympia electronics Power Light Series Manuel de l'opérateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics WEATHER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics OLY-1004 Manuel utilisateur

olympia electronics

olympia electronics GR-796/ST/DUO/ADR Manuel utilisateur

olympia electronics

olympia electronics BAU LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-938/15L Manuel utilisateur

olympia electronics

olympia electronics Classic Light Series Manuel utilisateur

olympia electronics

olympia electronics GR-8/leds Manuel utilisateur

olympia electronics

olympia electronics EASY LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-290/WP Manuel utilisateur

olympia electronics

olympia electronics OLY-500 Manuel utilisateur

olympia electronics

olympia electronics SLIM LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-490/WP/ADR Manuel utilisateur

olympia electronics

olympia electronics GRL-38/90/M Manuel utilisateur

olympia electronics

olympia electronics GR-939/30L/LT Manuel utilisateur

olympia electronics

olympia electronics GR-108/12L/90 Manuel utilisateur

olympia electronics

olympia electronics Double Easy Light GR-391/L Manuel utilisateur

Manuels Lanterne populaires d'autres marques

KYOWA

KYOWA KW-9114 Manuel utilisateur

Stahl

Stahl ECOLUX 6610 Series Manuel utilisateur

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuel utilisateur

PRG

PRG VARI LITE VL5 Manuel utilisateur

Raytec

Raytec VARIO2 series Manuel utilisateur

ENSA

ENSA LEDBT18WS2 Manuel utilisateur

LUG

LUG OFFICE LB LED N/T Manuel utilisateur

GE Wallighter 250 Manuel utilisateur

Draper

Draper RLEDL19/B Manuel utilisateur

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuel utilisateur

Panasonic

Panasonic EY3741B57 Manuel utilisateur

Clas Ohlson

Clas Ohlson LCC8T Manuel utilisateur

Coolon

Coolon WDN-140 Manuel utilisateur

Holiday Travel

Holiday Travel 834873 Manuel utilisateur

BEGA

BEGA 84 036 Manuel utilisateur

BEGA

BEGA 33 596 Manuel utilisateur

Dale Tiffany

Dale Tiffany GT701162 Manuel utilisateur

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuel utilisateur

olympia electronics GR-270 Manuel utilisateur

Manuels Lanterne populaires d'autres marques