Olympia electronics WEATHER LIGHT Series Manuel utilisateur

Thank you for purchasing this product of

Olympia Electronics. A European manufacturer.

GENERAL

These luminaires are used in places where

emergency luminaires are needed.

Each luminaire must be permanently connected

to mains power supply. In normal operation the

battery is charging and the 2 yellow LED’s light

in the screen (see step 4 on page 2). In case of

a mains power supply failure the luminaire

will light the led strip automatically in

emergency mode. When the mains power

supply is restored the device turns to normal

operation.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance or

testing must be done by authorized personel

only.

2. The device must be connected to the mains

power supply thru a fuse dependent by the total

amount of the line’s power load.

3. It is sugested to check every month the

indication LED for battery charging, and by

pushing the TEST button (see the paragraph 9

on page 2), to check the emergency cirquit. The

lamp should light as long as the TEST button is

pressed

4. It is sugested to check every 6 months the

minimum autononous duration by disconnecting

. In the opposite condition contact the

installer.

the mains power supply. Count the time that the

led strip lights and in case of less time than the

minimum autonomous duration the battery must

be replaced. If the measured time is

considerably less than the minimum autonomous

duration The replacement of

the battery and the light source must be done

u s i n g p a r t s o f t h e s a m e t y p e , b y t h e

manufacturer or by a competent person.

t i

in battery recycling

points. Do not incinerate.

INSTALLATION

To install the luminaire follow the installation

instructions οn page 2.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

0: Non Maintained

A: Including test device

*90: 90min duration

180: 180min duration

contact the installer.

5. In case of inactive use for a period greater

than 2 months, disconnect the battery by pulling

out the battery’s connector.

6. I s not allowed to discard batteries in to

comm on tra s h bin s , they must b e

discarded only

‘’ WEATHER LIGHT ‘’ SERIES FOR NON-MAINTAINED EMERGENCY LUMINAIRES

Bayblent FR3010, transparent polycarbonate

TECHNICAL CHARACTERISTICS

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERIES (Ni-Cd)

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

ILLUMINATION SOURCE

24h

Charge indication LED, TEST button

From overcharge and full discharge

IP 65

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

0 to 40 C

Up to 95%

3 years (1 year for the battery)

363 x 145 x 73 mm

Page 1 from 2

GR-936/30L

GR-935/30L

GR-936/15L

GR-935/15L

220-240V AC/50-60Hz

3.6V/3Ah

3.6W / 4.3VA

3.6V/1.5Ah3.6V/0.6Ah

2.5W / 3VA

180 min90 min

210lm 210lm

30 white LED’s 30 white LED’s

105lm 105lm

15 white LED’s 15 white LED’s

1000gr.830gr. 905gr.

923936010_23_008

High Quality European based Manufacturers

Page 2 from 2

9 Unfasten the mounting screws (step 8) and remove the diffusor.

When the luminaire is supplied by the mains, press on the marking for

TEST as shown in the picture below. Mount the diffusor by using the 4

removed screws.

TEST procedure with extra care!!

1 Remove the diffusor. Place simultaneously 2 flat blade screwdrivers and pull up gently the

reflector.

2 Install the included plastic cover in to the unused hole and install the base plastic (with the

included mounting screws and plugs).

3 Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F type

2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).

ATTENTION!! The cable must not be deformed in any way (This requirement is important to

ensure the tightness isolation IP 65). Install the cable gland, pass the round cable thru and

tighten it all the way.

4 Place the battery’s connector to the corresponding connector on the P.C.B. NOTE!! If you don’t

need the yellow led’s to light in normal operation, then remove the led jumper.

5 Connect the mains as shown in figure (connect the ground wire if required).

6 Install the included tie (if needed) to fasten securely the power cables.

7 Refit the reflector and fasten the two small screws (included).

8 Finaly place the diffusor by using the 4 included screws (tightening torque 1.2Nm).

INSTALLATION INSTRUCTIONS

L N

Mains connection

NOTE!! After finishing the installation you must power the luminaire at least for 24 hours for

battery charging to perform the named autonomy.

Battery replacement

1. Unfasten the 4 retaining screws (step 8 of the installation instructions) and remove the diffusor.

2. Unfasten the 2 retaining screws step 7 of the installation instructions and remove the reflector.

3. Remove the old battery and place a new on of the same type and characteristics.

4. Replace the removed parts (previous steps 1,2).

923936010_23_008

LED

JUMPER

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels olympia electronics Lanterne

olympia electronics

olympia electronics POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-470 Manuel utilisateur

olympia electronics

olympia electronics GR-490/WP/ADR Manuel utilisateur

olympia electronics

olympia electronics SLD-28/DZ Manuel utilisateur

olympia electronics

olympia electronics GR-900/30L/SC Manuel utilisateur

olympia electronics

olympia electronics GR-108/12L/90 Manuel utilisateur

olympia electronics

olympia electronics BAU LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics WATERPROOF POWER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-290 Manuel utilisateur

olympia electronics

olympia electronics WEATHER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics EASY LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics OLY-1004 Manuel utilisateur

olympia electronics

olympia electronics KLIN-20/ST Manuel utilisateur

olympia electronics

olympia electronics GR-939/30L/LT Manuel utilisateur

olympia electronics

olympia electronics LLB-26/90 Manuel utilisateur

olympia electronics

olympia electronics GR-2110 Manuel utilisateur

olympia electronics

olympia electronics Classic Light Series Manuel utilisateur

olympia electronics

olympia electronics GR-427/12L Manuel utilisateur

olympia electronics

olympia electronics OLY-1024/WL Manuel utilisateur

olympia electronics

olympia electronics GRL-37/90/ADR Manuel utilisateur

olympia electronics

olympia electronics GR-220/DUO/M Manuel utilisateur

olympia electronics

olympia electronics KLIN-20/ST/ADR Manuel utilisateur

olympia electronics

olympia electronics GR-290/M Manuel utilisateur

olympia electronics

olympia electronics GR-427/12L/MAR Manuel utilisateur

Manuels Lanterne populaires d'autres marques

KYOWA

KYOWA KW-9114 Manuel utilisateur

Stahl

Stahl ECOLUX 6610 Series Manuel utilisateur

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuel utilisateur

PRG

PRG VARI LITE VL5 Manuel utilisateur

Raytec

Raytec VARIO2 series Manuel utilisateur

ENSA

ENSA LEDBT18WS2 Manuel utilisateur

LUG

LUG OFFICE LB LED N/T Manuel utilisateur

GE Wallighter 250 Manuel utilisateur

Draper

Draper RLEDL19/B Manuel utilisateur

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuel utilisateur

Panasonic

Panasonic EY3741B57 Manuel utilisateur

Clas Ohlson

Clas Ohlson LCC8T Manuel utilisateur

Coolon

Coolon WDN-140 Manuel utilisateur

Holiday Travel

Holiday Travel 834873 Manuel utilisateur

BEGA

BEGA 84 036 Manuel utilisateur

BEGA

BEGA 33 596 Manuel utilisateur

Dale Tiffany

Dale Tiffany GT701162 Manuel utilisateur

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuel utilisateur