Olympia electronics GR-938/15L Manuel utilisateur

Thank you for purchasing this product of Olympia

Electronics. A European manufacturer.

GENERAL

These luminaires are used in places where

emergency luminaires are needed. Each

luminaire must be permanently connected to

mains power supply. In normal operation the led

strip lights and the battery is charging. In case of

a mains power supply failure the luminaire will

light the led strip automatically in emergency

mode. When the mains power supply is

restored the device turns to normal operation.

INSTALLATION

To install the luminaire follow the installation

instructions on page 2.

OPERATION

Battery Cut-off

The luminaire enters in this operation when the

mains power supply fails and battery has lost its

energy. During this operation the luminaire enters

the idle state and battery consumption is

negligible, in order to be protected from deep

discharge.

Battery charging

The battery charging is completely controlled. In

this case, is achieved the perfect battery

maintenance , as well as the elongation of its

duration. When the battery has completely

charged, it charges with a maintenance current.

Manual Test

The manual test can be conducted only if the

main power supply and the battery is connected.

By pressing the TEST/RESET button briefly (page

2) an operation test is initiated. During this test

period all indication LEDs are OFF.

Automatic test

This test includes all the operations that provide

the manual test and is conducted automatically

every 15 days. In order to be performed, the main

power supply and the battery should be connected.

Automatic Autonomous Test

The Automatic Autonomous Test is conducted and

measures the luminaire`s back up operation. This

test is conducted automatically every six months.

In order to be performed, the main power supply

and the battery should be connected (the battery

should be charged). If the battery is not charged,

the test is postponed until the battery is completely

charged. If during the Automatic Autonomous Test

the luminaire’s duration is lower than the named,

then the battery must be replaced.

Back Up Operation

The autonomous duration of battery during

emergency mode is at least the one that is stated

in the technical characteristics. During emergency

mode, a LED strip test is also performed.

Resetting Errors

Push the TEST/RESET button for 5 seconds, to

extinguish all the indicated LED errors (page 2).

Then the luminaire enters regular operation mode.

Indication LED status

(with connected mains power supply).

Charge

On: Good charge current.

Οff: No battery (No charging current or

disconnected battery).

Lamp fault

Οn: faulty LED strip.

Off: Good LED strip.

Fault

Οff: Battery OK.

WATERPROOF SELF-TESTING EMERGENCY LUMINAIRES

Page 1 from 2

220-240V AC/50-60Hz

5W / 8.5VA

Bayblend FR3010, transparent polycarbonate

TECHNICAL CHARACTERISTICS

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERY (Ni-Cd)

CHARGING TIME

INDICATIONS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

ILLUMINATION (MAINS / EMERGENCY)

ILLUMINATION SOURCE

90min

24h

Charge, lamp fault, fault indication LED

From overcharge and full discharge

IP 65

3.6V/3Ah

210lm / 210lm

30 white LED’s

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

0 to 40 C

Up to 95%

3 years (1 year for the battery)

920gr.

363 x 145 x 73 mm

3.5W / 7.5VA

3.6V/1Ah

105lm / 105lm

15 white LED’s

180min

5W /8.5VA3.5W / 7.5VA

3.6V/1.5Ah

210lm / 210lm 105lm / 105lm

30 white LED’s

210lm / 210lm

15 white LED’s

GR-938/30LGR-938/15L GR-939/15L GR-939/30L

790gr. 860gr.

923939100_09_006

High Quality European based Manufacturers

Page 2 from 2

Blink (With Charge LED ON): Autonomy or low

battery problem

(the battery must be replaced).

Blink (With Charge LED Off):

No charging current or disconnected battery.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance or

testing must be done by authorized personel only.

2. The device must be connected to the mains

power supply thru a fuse dependent by the total

amount of the line’s power load.

In case of battery or lamp replacement, these

must be replaced by parts of the same type, by

the manufacturer or by a competent person.

4. In case of inactive use for a period greater than

2 months, disconnect the battery by pulling out

the battery’s connector.

5. I s not allowed to discard batteries in to

common trash bins, they must be discarded

only

t i

in battery recycling points. Do not

incinerate.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

1: Maintained

A: Including test device

*90: 1.5 hour duration

180: 3 hour duration

NOTE!! After finishing the installation you must

power the luminaire at least for 24 hours for

battery charging to perform the named

autonomy.

Manual TEST or Resetting Errors

In order to test or reset the device you

must carefully remove the diffusor by

unfastening the 4 mounting screws.

Then push the button as described in

the according paragraphs on page 1.

L1 L N N

L1 L N

External

switch

Controlled operation of the lamp

Link

Permanent maintained operation

1 Remove the diffusor. Place simultaneously 2 flat blade screwdrivers and pull up gently the

reflector.

2 Install the included plastic cover in to the unused hole and install the base plastic (with the

included mounting screws and plugs).

3 Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F

type 2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).

ATTENTION!! The cable must not be deformed in any way (This requirement is important

to ensure the tightness isolation IP 65). Install the cable gland, pass the round cable thru and

tighten it all the way.

4 Place the battery’s connector to the corresponding connector on the P.C.B.

5 Connect the mains cables to the respective terminal block (connect the ground wire if required).

6 Ν for neutral, L for live wire and L1 for the maintained operation. The L1 wire can be connected

to an external switch to control the maintained or non maintained operation of the luminaire.

7 For permanent maintained operation use two wires to power the luminaire, Ν for neutral and L for

live wire, and link the L and L1.

8 Install the included tie (if needed) to fasten securely the power cables.

9 Refit the reflector and fasten the two small screws (included).

10 Finaly place the diffusor by using the 4 included screws (tightening torque 1.2 Nm).

INSTALLATION INSTRUCTIONS

234

923939100_09_006

Ce manuel convient aux modèles suivants

Autres manuels olympia electronics Lanterne

olympia electronics

olympia electronics GR-490/WP/ADR Manuel utilisateur

olympia electronics

olympia electronics Slim Light Series Manuel utilisateur

olympia electronics

olympia electronics GR-220/DUO/M Manuel utilisateur

olympia electronics

olympia electronics GR-579/L/90/WP Manuel utilisateur

olympia electronics

olympia electronics OLY-1004/WP/ADR Manuel utilisateur

olympia electronics

olympia electronics OLY-500 Manuel utilisateur

olympia electronics

olympia electronics GR-490/ADR Manuel utilisateur

olympia electronics

olympia electronics WEATHER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics OLY-1004 Manuel utilisateur

olympia electronics

olympia electronics OLY-1024/WL Manuel utilisateur

olympia electronics

olympia electronics SLD-28/DZ Manuel utilisateur

olympia electronics

olympia electronics BAU LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-490/WP Manuel utilisateur

olympia electronics

olympia electronics GR-108/12L/90 Manuel utilisateur

olympia electronics

olympia electronics EASY LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics Double Easy Light GR-391/L Manuel utilisateur

olympia electronics

olympia electronics GRL-38/90/M Manuel utilisateur

olympia electronics

olympia electronics GR-427/12L Manuel utilisateur

olympia electronics

olympia electronics LLB-26/90 Manuel utilisateur

olympia electronics

olympia electronics Power Light Series Manuel de l'opérateur

olympia electronics

olympia electronics CLASSIC LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-796/ST/DUO/ADR Manuel utilisateur

olympia electronics

olympia electronics WEATHER LIGHT Series Manuel utilisateur

olympia electronics

olympia electronics GR-939/30L/LT Manuel utilisateur

Manuels Lanterne populaires d'autres marques

KYOWA

KYOWA KW-9114 Manuel utilisateur

Stahl

Stahl ECOLUX 6610 Series Manuel utilisateur

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuel utilisateur

PRG

PRG VARI LITE VL5 Manuel utilisateur

Raytec

Raytec VARIO2 series Manuel utilisateur

ENSA

ENSA LEDBT18WS2 Manuel utilisateur

LUG

LUG OFFICE LB LED N/T Manuel utilisateur

GE Wallighter 250 Manuel utilisateur

Draper

Draper RLEDL19/B Manuel utilisateur

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuel utilisateur

Panasonic

Panasonic EY3741B57 Manuel utilisateur

Clas Ohlson

Clas Ohlson LCC8T Manuel utilisateur

Coolon

Coolon WDN-140 Manuel utilisateur

Holiday Travel

Holiday Travel 834873 Manuel utilisateur

BEGA

BEGA 84 036 Manuel utilisateur

BEGA

BEGA 33 596 Manuel utilisateur

Dale Tiffany

Dale Tiffany GT701162 Manuel utilisateur

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuel utilisateur

olympia electronics GR-938/15L Manuel utilisateur

Manuels Lanterne populaires d'autres marques