Flashforge Adventurer 5M Manuel utilisateur
Adventurer 5M
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch
2
English
3 –21
Čeština
22 –40
Slovenčina
41 –59
Magyar
60 –78
Deutsch
79 –98
3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
www.alza.co.uk/kontakt
✆+44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz
Safety Notice
Please carefully read and strictly follow all the safety warnings and notices below all the
time.
Note: Each 3D printer undergoes printing tests before leaving the factory. Filament
residue on the nozzle or slight scratches on the build plate are normal and do not affect
usage.
Work Environment Safety
•Please keep the workspace clean and tidy.
•Please ensure the equipment operates away from combustible gases, liquids,
and dust. High temperatures generated during operation may react with
combustible gases, liquids, or airborne dust, potentially causing fires.
•Children and untrained individuals should not operate the equipment alone.
Electrical Safety
•Please properly ground the equipment. Do not modify the plug. Ungrounded
equipment/improperly grounded equipment/modified plug will inevitably
increase the risk of electric leakage.
•Avoid exposing the equipment to damp or direct sunlight environments.
Humidity will increase the risk of electric leakage. Exposure to sunlight will
accelerate the aging of plastic parts.
•Make sure to only use the power cord provided by Flashforge.
•Do not use the equipment during thunderstorms.
•Please turn off the equipment and unplug it if it is not in use for a long time.
4
Personal Safety
•Do not touch the extruder, build plate, etc., during printing.
•Do not touch the extruder and build plate after finishing printing to avoid high
temperature burns or mechanical damage.
•Do not wear scarves, masks, gloves, jewelry, or other objects that can easily get
tangled into the equipment while operating it.
•Do not operate the equipment while you are tired or under the influence of
drugs, alcohol, or medication.
Cautions
•Keep the inside of the equipment clean. Do not drop metal objects into the
grooves at the bottom of the build plate.
•Please clean up filament debris in time. It is recommended to operate this
outside the equipment.
•Any modification of the equipment by yourself will void the warranty.
•Please keep the distance between the extruder and build plate for at least 50mm
during filament loading. Too-close distance may cause nozzle clogs.
•Please operate the equipment in a well-ventilated environment.
•Do not use the equipment for illegal activities.
•Do not use the equipment to make food storage containers.
•Do not place printed models into your mouth.
Equipment Environment Requirements
Room temperature: 15-30℃; Humidity: 20-70RH%
Equipment Placement Requirements
The equipment must be placed in a dry and well-ventilated environment. A distance of
at least 20cm must be reserved around the front, back, left, and right sides of the
equipment. Recommended storage temperature: 0-40°C.
Compatible Filament Requirements
When using this equipment, it's recommended to use Flashforge's filaments. If non-
Flashforge filaments are used, there will be certain differences in material properties,
and print parameters may need adjustments.
Filament Storage Requirements
Please store filaments in a dry and dust-free environment after unpacking. It is
recommended to use the matching filament dry box for storage.
5
Equipment Introduction
1. Extruder
2. Touch screen
3. Build plate
4. USB port
5. Screw holes for spool holder
6. Filament detection sensor
7. Ethernet port
8. Power switch
9. Power socket
6
Printer Parameters
Device name
Adventurer 5M
Extruder quantity
1
Printing precision
±0.2mm (testing based on 100mm cubes)
Positioning accuracy
X/Y-axis: 0.0125mm
Z-axis: 0.0025mm
Layer thickness
0.1-0.4mm
Build volume
220×220×220mm
Nozzle diameter
0.4mm default (0.25/0.6/0.8mm optional)
Printing speed
10-300mm/s
Max acceleration
20000mm/s2
Max travel speed
600mm/s
Max extruder temperature
280°C
Supported filament
*PLA/*PETG (0.4mm nozzle)
*TPU/PLA-CF/PETG-CF (0.6/0.8mm nozzle)
Note: Materials marked with * are
recommended for printing.
Power supply
AC 100~120V / 200~240V, 50/60Hz, 350W
Device size
353×376×413mm (excluding the display
and spool holder)
262×402×448mm (including the display,
excluding the spool holder)
Net weight
10.8kg
Connectivity
USB/Wi-Fi/Ethernet
Operating temperature
15~30°C
Compatible operating system
Windows 7/8/10/11; Linux (Ubuntu 20.04
or later); MacOS (10.9 or later)
Slicing software
FlashPrint 5
Maximum platform temperature
110°C
Levelling method
One-click auto levelling
Filament run-out reminder
Yes
Power loss recovery
Yes
Smart touch screen
4.3”
Build plate
PEI flexible steel plate
7
Initial Setup
Unboxing
Safety notice: Do not power on the printer until the installation is completed.
First, open the box. Remove the upper foam packaging, Quick Start Guide and After-
sales Service Card. Take out the machine, place it on a level workspace and remove the
packaging bags and tapes. Remove the filament, power cable, screen, and accessory box
from the chamber protective foam. Remove the inner protective foam from the
extruder. Move the chamber foam according to the arrow direction and remove the
foam.
Packing List
•3D printer
•Filament
•Power cable
•After-sales service card
•Quick start guide
•Touch screen
•Spool holder (with 2 screws)
•Grease
•Glue
•Diagonal pliers
•Unclogging pin tool
•Screwdriver
•Allen wrench (2.0, 2.5, 3.0)
Installing the Spool Holder and Filament Guide Tube
Take out the two screws and spool holder from the accessory box. Install the spool
holder at the position shown in the figure with the two screws. (Note: Please tighten
them using a 2.0mm Allen wrench.)
8
Insert the filament guide tube to the extruder and insert the other end of the filament
guide tube into the filament detection sensor.
Installing the Screen
Note: Before the installation, please remove the tape of the screen cable. Tear it off
gently to avoid damaging the cable.
As shown in the picture, insert the screen cable into the screen connector.
Lift the buckle on the screen's cable socket to the indicated position (Fig. 1), then insert
the screen cable into the socket connector. Note: Ensure proper insertion and check
alignment of the indicator line with socket. Press down the buckle on the cable socket to
the indicated position according to the arrow direction (Fig. 2).
9
Insert the buckle on the back of the screen into the printer's slot and push the screen
according to the arrow direction to lock it in place.
Unlocking the Build Plate
Note: Please ensure that the platform has been cleared up!
Please use a 2.0mm Allen wrench to remove four screws which lock the build plate (as
indicated by the arrow).
First Print
Power on the printer, turn on the power switch, and wait for the screen to respond.
Following the guide on the screen, select your preferred language. Upon language
selection, click [Next] and the machine will perform the first calibration. Vibrations and
noise during calibration are normal. (Note: Please keep the machine on a stable surface
and do not move it during calibration.)
Load the filament. First, cut off the bent part of the filament end. Hang the filament on
the spool holder. Pass it through the filament sensor until it's seen from the other end
of the filament guide tube. Push it forward to the feed roller, until it cannot go further.
(Please use PLA filament for the first print on initial setup).
10
Click [Load] and select [PLA] for the first print. Wait for the extruder to heat up. Feeding
will begin after heating. Successful filament extrusion from the nozzle indicates
successful loading. Lastly, confirm the filament guide tube is properly inserted.
Note: If no filament is extruded, manually insert the filament into the inlet and click
[Back] to retry. Feel for filament movement until it is extruded.
Please clear the filament residues on the nozzle and platform. Users must apply glue to
the platform so as to improve adhesion for the first print. Click [Print] and the machine
starts printing the built-in file (configured for PLA material).
Software Introduction & Installation
Before printing 3D model files, you need to configure slicing presets for the
corresponding printer. Recommended slicing software: OrcaSlicer / FlashPrint 5
Pre-printing steps:
•Obtain the 3D file (STEP/STL/OBJ).
•Download and install the slicing software.
•Use the slicing software to convert the file into the machine-readable format.
•Import the sliced file via a USB flash drive or network transfer to the printer for
printing.
Table des matières
Langues :
Autres manuels Flashforge Imprimante 3D
Flashforge
Flashforge Creator 4 Manuel utilisateur
Flashforge
Flashforge DREAMER Manuel utilisateur
Flashforge
Flashforge Finder Manuel utilisateur
Flashforge
Flashforge AD1 Manuel utilisateur
Flashforge
Flashforge Finder Manuel utilisateur
Flashforge
Flashforge Creator 3 Pro Manuel utilisateur
Flashforge
Flashforge Inventor II Manuel utilisateur
Flashforge
Flashforge Creator 3 Pro Manuel utilisateur
Flashforge
Flashforge Adventurer 5M Pro Manuel utilisateur
Flashforge
Flashforge Guider II Manuel utilisateur
Flashforge
Flashforge ADVENTURER 3 Manuel utilisateur
Flashforge
Flashforge DREAMER Manuel utilisateur
Flashforge
Flashforge Guider II Manuel utilisateur
Flashforge
Flashforge Adventurer 4 Manuel utilisateur
Flashforge
Flashforge Adventurer 4 Manuel utilisateur
Flashforge
Flashforge DREAMER Manuel utilisateur
Flashforge
Flashforge Hunter Manuel utilisateur
Flashforge
Flashforge Guider IIs Manuel utilisateur
Flashforge
Flashforge Finder 3 Manuel utilisateur
Flashforge
Flashforge EN-A01 Manuel utilisateur
