Flashforge Adventurer 3 Pro 2 Manuel utilisateur
This guide is only applicable to FLASHFORGE Adventurer 3 Pro 2 3D Printer.
EN-A03 Adventurer 3 Pro 2
Scan the QR code to view
the unboxing video.
1.1 - Components Introduction
1.2 - Parameters
2.1 - Unpacking
2.2 - Accessories
2.3 - PEI Build Plate Installation
2.4 - Printing
2.4.1 - Software Installation
2.4.2 - Equipment Preparation
2.4.2.1 - Leveling and Calibration
2.4.2.2 - Flilament Loading
2.4.3 - Model File Transfer
2.4.4 - Printing
2.4.4.1 - FlashCloud Printing
2.4.4.2 - Polar Cloud Printing
2.4.5 - Model Removal
2.4.6 - Filament Change
2.5 - User Interface Introduction
2.5.1 - Build
2.5.2 - Tools
2.5.2.1 - Network
2.5.2.2 - Preheat
2.5.2.3 - Setting
2.5.2.4 - About
2.5.3 - Filament
2.6 - Camera Instructions
2.6.1 - FlashCloud Camera Use
2.6.2 - Polar Cloud Camera Use
2.6.3 - Cloud-Based Camera Control
2.6.4 - Error Handling
06
07
08
10
11
12
12
12
12
14
17
21
22
24
28
29
30
30
32
32
35
36
40
41
42
43
45
47
49
Chapter 1: Adventurer 3 Pro 2
Chapter 2: Operating
Chapter 3: Q&A
Chapter 4: Help and Support
06
08
50
54
CONTENTS
Preface
Notice
Terms
Note: Each device must be tested before leaving the factory. If there are some residues in
the extruder or some tiny scratches on the build tape, it is normal and won’t affect
the printing quality.
On the completion of this User Guide, thanks all Flashforge engineers and Flashforge 3D
printer users for their unremitting efforts and sincere assistance.
The Flashforge Adventurer 3 Pro 2 user guide is designed for users to start their printing
journey with Flashforge Adventurer 3 Pro 2. Even if you are familiar with earlier Flashforge
machines or 3D printing technology, we still recommend you to read this guide, as there is
lots of important information about the Adventurer 3 Pro 2 for you to get a better 3D
experience.
For a better and more successful printing experience, you can refer to the following materials:
Quick Start Guide:
Users will find the Quick Start Guide together with the printer accessories. The Quick Start Guide
will help you start your print journey as soon as possible.
Official Flashforge Website: www.flashforge.com
The official Flashforge website contains the up-to-date information concerning Flashforge
software, firmware, device maintenance and so on. Users are also able to get the contact
information from there.
Preface
01
Work Environment Safety
Electrical Safety
Personal Safety
Cautions
Keep your work place tidy.
Do not operate the printer in the presence of flammable liquids, gases or dust.
Keep the printer out of children and untrained people’s reach.
Always use the printer with a properly grounded outlet. Do not refit Adventurer 3 Pro 2 plug.
Do not use the printer in damp or wet locations. Do not expose the printer to burning sun.
In case of device damage, please use the power cord provided by Flashforge.
Avoid using the device during an thunderstorm.
In case of uncertain accident, please unplug the device if you do not use it for long.
Do not touch the nozzle and build plate during printing.
Do not touch the nozzle after finishing printing.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves
away from moving parts.
Do not operate the device while you are tired or under the influence of drugs, alcohol or
medication.
Do not leave the device unattended for long.
Do not make any modifications to the device.
Lower the build plate before loading/unloading filament.
[The distance between the nozzle and build plate should be kept for at least 50mm.]
Operate the device in a well-ventilated environment.
Never use the device for illegal activities.
Never use the device to make any food containers.
Never use the device to make any electrical appliance.
Never put the model into your mouth.
Do not remove the models with brute force.
Safety Notice: PLEASE READ AND STRICTLY FOLLOW ALL THE
SAFETY WARNINGS AND NOTICE BELOW.
Notice
02
Operating Environment Requirements
Equipment Placement Requirements
Filament Requirements
Filament Storage
Legal Notice
Temperature: RT 15-30 ℃; Moisture: 20%-70%
The device must be placed in a dry and ventilated environment.
The distances of the left, right and back side space should be at least 20cm, and
the distance of the front side space should be at least 35cm. Device storage
temperature: RT 0-40 ℃
Please make sure you use the Flashforge filament or the filament from the brands
accepted by Flashforge.
Nozzle clogging and damage may be caused by non-Flashforge filament due to
inappropriate material properties.
All the information in this document is subject to any amendment or change without
the official authorization from Flashforge.
Flashforge makes no warranty of any kind with regard to this document, including,
but not limited to, the implied warranties of merchantability and fitness for a particular
purpose.
Flashforge shall not be liable for errors contained herein for incidental consequential
damages in connection with furnishing, performance or use of this material.
This document contains proprietary information protected by copyright.
Copyright 2023 Zhejiang Flashforge 3D Technology Co., Ltd. All rights reserved.
All polymers degrade with time. Do not unpack the filament unless it is required for use.
Please keep the storage environment dry and dust-free.
03
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
04
The surface on which the Adventurer 3 Pro 2 builds an object
Build Tape
Build Plate
The black tape that covers Adventurer 3 Pro 2’s build plate so
that the object can stick to the build plate well
Build Volume The dimensions of the space into which 3D prints can be
produced. The largest build volume is 150*150*150mm.
Extruder
Nozzle
Cooling Fan
Filament Cartridge
Filament Guide Tube
Filament Intake
Solid Glue Stick
The integral extruder assembly is installed on X-axis.
The extruder draws the filament from the filament spool,
melts it and extrudes it through the nozzle into the build plate.
Also called ‘print head’, which is located at the bottom
of the extruder where heated filament is squeezed out.
A specific box for placing Flashforge filament, which is
located on the right of the printer.
A white plastic tube that guides the filament from the
filament box to the filament intake
A solid adhesive used for making the model stick to the
build plate firmly
To cool the outer assembly of the extruder and gear motor
An opening located at the top of the extruder
Terms
05
1.1 Components Introduction
1. Filament guide tube 2. Filament guide tube joint 3. Extruder base 4. Cooling fan
5. Removable nozzle 6. Extruder cables 7. Clip 8. Led light 9. Air guide duct
10. Front door 11. Y-axis sliding slot 12. Platform base 13. Build plate
14. Touch screen 15. USB stick input 16. Power switch 17. Power input
18. Spool holder 19. Filament cover 20. Filament cover handle
21. Motor 22. Filament intake 23. Filament feeding wheel 24. Top cover
25. Air outlet 26 Ethernet input
Chapter 1: Adventurer 3 Pro 2
06
1.2 Parameters
Name
Number of Extruder
Print Technology
Screen Size
Build Volume
Layer Thickness
Build Accuracy
Positioning Accuracy
Filament Diameter
Nozzle Diameter
Build Speed
Software
Supported Formats
Memory Size
OS
Input
Connectivity
Device Size
Net Weight
Adventurer 3 Pro 2
1, Removable
Fused Filament Fabrication [FFF]
2.8”color Touch Screen
150*150*150 mm
0.1-0.4 mm
± 0.2 mm
Z-axis 0.0025mm; XY-axis 0.011 mm
1.75 mm [± 0.07 mm]
0.4 mm
10-300 mm/s
FlashPrint
Input: 3mf/stl/obj/fpp/bmp/png/jpg/jpeg File
Output: gx/g File
8 G
Windows XP/Vista/7/8/10, Mac OS, Linux
150W [24V, 6.25A]
USB, Wi-Fi, Ethernet
388*340*405 mm
9 kg
07
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Flashforge Imprimante 3D
Flashforge
Flashforge Finder Manuel utilisateur
Flashforge
Flashforge Finder Manuel utilisateur
Flashforge
Flashforge Guider 3 Manuel utilisateur
Flashforge
Flashforge Inventor Manuel utilisateur
Flashforge
Flashforge Creator Pro Manuel utilisateur
Flashforge
Flashforge Guider 3 Plus Manuel utilisateur
Flashforge
Flashforge Inventor Manuel utilisateur
Flashforge
Flashforge Creator Pro 2 Manuel utilisateur
Flashforge
Flashforge Inventor II Manuel utilisateur
Flashforge
Flashforge Finder Manuel utilisateur
Flashforge
Flashforge Inventor II Manuel utilisateur
Flashforge
Flashforge Guider II Manuel utilisateur
Flashforge
Flashforge Creator 3 Manuel utilisateur
Flashforge
Flashforge DREAMER Manuel utilisateur
Flashforge
Flashforge Guider II Manuel utilisateur
Flashforge
Flashforge Adventurer3 Manuel utilisateur
Flashforge
Flashforge Adventurer 4 Manuel utilisateur
Flashforge
Flashforge Guider Manuel utilisateur
Flashforge
Flashforge Guinder II Manuel utilisateur
Flashforge
Flashforge Adventurer 4 Manuel utilisateur
