AnyCubic Kossel Plus Manuel utilisateur

Table des matières

Autres manuels AnyCubic Imprimante 3D

AnyCubic

AnyCubic Kobra Go Manuel utilisateur

AnyCubic

AnyCubic Kobra Manuel utilisateur

AnyCubic

AnyCubic Wash and Cure Manuel utilisateur

AnyCubic

AnyCubic Kobra Manuel utilisateur

AnyCubic

AnyCubic Prusa i3 Manuel utilisateur

AnyCubic

AnyCubic i3 MEGA Manuel utilisateur

AnyCubic

AnyCubic i3 MEGA Manuel utilisateur

AnyCubic

AnyCubic Photon Mono Manuel utilisateur

AnyCubic

AnyCubic VYPER Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur

LONGER

LONGER LK4 Pro Manuel utilisateur

Modification for Anycubic Kossel Plus 3D Printer

To print large size object (such as φ230×200), the printer needs modifications.

1. Assembling

As page 4 in the manual, add copper spacers(C19, new part)between effector

and CFT-JBs, as the following figure shows, and fix them with HSHCS M3×20 (C02).

As page 5 in the manual, add copper spacers (C19) between belt tensioners

and CFT-JBs, as the following figure shows, and fix them with HSHCS M3×25 (C20,

new part)instead of HSHCS M3×20 (C02).

Please make sure C19 are in right directions.

C02

C19

C19

C20

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

Assemble the linear rails (D06) as the following figures show.

2. Firmware

Change the parameters in firmware as the following figure shows or download the

latest firmware from Google Drive

(https://drive.google.com/open?id=0B8VIB533cgdMSVMxNm43aG1OQ0U).

DELTA_DIAGONAL_ROD change 267 to 271.5 or the number you debug (Page

19 in the manual);

DELTA_SMOOTH_ROD_OFFSET change 188 to 187 or the number you debug;

DELTA_PRINTABLE_RADIUS change 115 to 116；

For the limit switches have been moved down, the height need to be adjusted

(Page 18), and you also need level the platform.

Less

than

67mm

Less

than

15mm

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

3. Cura

Change the width and depth to a number bigger than 230 such as 240

Change the start distance to 0.5 (3 for default) in expert config.

To print small parts, it is suggested to change the start distance back to 3.

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC