CYP PU-2H8HBTE-AD Manuel utilisateur
PU-2H8HBTE-AD
2 x 8 HDBaseT™ Switch with Audio Dembedding
OPERATION MANUAL
3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 25/04/2014 First release
5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................7
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 8
6.3 IR Cable Pin Assignment.......................10
6.4 Remote Control........................................10
6.5 RS-232 Pin Denition .............................11
6.6 RS-232 Commands..................................11
7. Connection Diagram .......................... 12
8. Specications...................................... 13
8.1 Technical Specications ........................13
8.2 CAT5e/6/7 Cable Specication ...........14
9. Acronyms............................................. 14
6
1. INTRODUCTION
The PU-2H8HBTE HDBaseT switch has two HDMI inputs and eight
HDBaseT outputs, plus a single HDMI output. This device allows the user
to select either HDMI source for distribution to all screens simultaneously.
Each HDBaseT output supports the transmission of video (resolutions up
to 1080p Full HD, plus 4K Ultra High Denition, and 1920x1200@60Hz),
multi-channel audio, single LAN serving, and control via 2-way IR, RS-
232 or Web GUI/Telnet IP over a single CAT5e/6/7 cable (up to 100m). The
HDMI output supports the same video resolutions and high denition
audio via certied HDMI cables up to 15m.
For additional exibility, the PU-2H4HBTE is provided with Audio De-
Embedding functionality allowing easy audio integration into a wider
AV system or direct connection to an AVR. Audio outputs are via a single
Optical connection or an Analogue Stereo output (2×RCA).
The HDBaseT outputs are designed to be used with any compatible
HDBaseT Receiver as follows: PU-507RX / PU-507RX-2H / PU-507RX-SCD /
PU-507WPRX / PU-1109RX. These Receivers support Power over Ethernet
(PoE) function so do not require a separate PSU for power.
Use the LAN serving capabilities of this switch to add internet connectivity
to every HDBaseT output zone. In addition, this switch also features IP
control allowing users to access and control the matrix remotely and also
allow additional options for integration of third-party control systems
such as Control 4.
2. APPLICATIONS
Household entertainment sharing and control
Lecture room display and control
Showroom display and control
3. PACKAGE CONTENTS
HDMI over HDMI & CAT5e/6/7 with PoE and Ethernet Transmitter
1× IR Receiver
1× IR Blaster
1× Remote Control
24V DC Power Adaptor
Power Cord
Operation Manual
7
4. SYSTEM REQUIREMENTS
Source equipment with HDMI output connector
Display TV/Monitor with HDMI input connector
HDMI over CAT5e/6/7 Receivers with industry CAT5e/6/7 cables
5. FEATURES
HDMI, HDCP and DVI complaint
Common supported resolutions: HDTV: 480p, 576p, 720p, 1080i,
1080p, 1080p24, 4K; PC: VGA, SVGA, XGA, WXGA, SXGA, UXGA, WUXGA,
1920x1200@60Hz
High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus
and DTS-HD Master Audio plus LPCM (up to 192kHz)
Uncompressed data transfer over single CAT cable for HDBaseT
outputs (100m - CAT6/7; 80m - CAT5e)
Supports HDMI input up to 15m 1080p 8bit or 10m 1080p 12bit.
Supports RS-232, 2-Way IR, Manual Selection Buttons, and Web GUI/
Telnet IP for control
HDBaseT outputs support Power over Ethernet (PoE) with compatible
receiver units
Supports LAN serving to all connected HDBaseT zones
Supports 3D signals and 4K Ultra High Denition
Note:
1. This system was tested with CAT6/23AWG cables, results may vary with
cables of a dierent specication.
2. The PoE function is designed for powering compatible Receiver units only
non-PoE Receivers will need their own power supply. Receivers of another
brand may not be compatible.
3. Displaying HDMI 4Kx2K resolution require the standard 4Kx2K HDMI cable
and display in order for proper image displaying.
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER SYNC HDMI
IN 1
HDMI
IN 2 HDMI
LINK
LINK 1LINK 2LINK 3LINK 4LINK 5LINK 6LINK 7LINK 8
CAT5e/6/7 OUT
1 2 3 4 5
1IR Window: Receive IR signal from the package included remote
control only.
2POWER Button & LED: Press this button to switch ON or set the
device to standby mode and the LED will illuminate in Green and Red.
3SYNC: This LED will illuminate when the HDMI input port connected
to the source.
4HDMI IN 1/2: Press the button to selection HDMI input source 1 or 2.
The LED will illuminate according to the selection.
5HDMI & CAT OUT LINK 1~8: These link LEDs will illuminate when
HDMI or CAT5e/6/7 output(s) has been connected to the Display/
Receiver(s) and the Receiver(s) has connected with display that shows
image on screen.
6.2 Rear Panel
87654321LAN OPTICAL
OUT
HDMI
OUT
HDMI
IN 2
HDMI
IN 1
RS-232
IR OUTL/R OUT
IR IN
SERVICE
STDTV
DC 24VDC 24V
EDID
CAT5e/6/7 OUT
1 3
2 11
54 6 7 8 9 10 12
1CAT5e/6/7 OUT 1~8: Connect these ports to CAT5e/6/7 to HDMI
Receivers (with or without PoE function) with CAT5e/6/7 cable to
extend the signal up to 100m.
2IR OUT: Connect with IR Blaster to blast out the IR signal received
from the Receiver side. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
3IR IN: Connect with IR Extender to receive IR signal from Transmitter
side and blast out at Receiver side. Ensure that remote controller
9
being used is within the direct line-of-sight of the IR Extender.
4LAN: Connect to intranet or internet service system for a total sharing
rate of 100Mbps within the link of Transmitter.
Warning: DO NOT connect this slot with any of the CAT5e/6/7 port, doing
so may trigger a power shot down and ruin the device.
5L/R OUT: Connect to active speaker or audio equipment for audio
signal output.
6OPTICAL OUT: Connect to active speaker or audio equipment for
audio signal output.
7HDMI OUT: Connect to HDMI display for instant image display or
cascade with another family type Transmitter.
8HDMI IN1/2: Connect with source equipment such as DVD/Blu-ray or
PS3 player.
9EDID STD/TV: The default factory setting is on TV, leave as it is when
the display is properly. The unit will detect rst the HDMI output’s
EDID and send out the signal accordingly to other output ports. If
the HDMI output port is not connected the device will detect the 1st
CAT5e/6/7 output's EDID and send out the signal accordingly to all
outputs.
This device obtain the last memory function therefore, the device will
use the last HMDI output port/the 1st CAT5e/6/7's output EDID after
power cycling or switch in between the EDID setting.
Switch to STD to use build-in EDID if the display has problem. STD
EDID's video at 1080p@60Hz and audio at LPCM 2CH.
10 SERVICE: This slot is reserved for factory service only.
11 RS-232: Connect this slot from PC/Laptop for RS-232 command
sending.
12 DC 24V: Plug the 24V DC power supply into the unit and connect the
adaptor to an AC outlet.
10
6.3 IR Cable Pin Assignment
3
1
3
2
2
1Power 3.3V
IR Blaster Signal
NC
IR Signal
Power 3.3V
Ground
IR Extender
IR Blaster
6.4 Remote Control
1Power: Press the button to turn
On/O the unit.
2Input Selection 1/2: Press 1/2 to
select HDMI input sources 1 or 2.
CR-37
POWER
1
2
Table des matières
Autres manuels CYP Changer
CYP
CYP CPLUS-401V Manuel utilisateur
CYP
CYP PU-8H8HBT Manuel utilisateur
CYP
CYP CDPS-UH4H1HFS Manuel utilisateur
CYP
CYP EL-5400 Manuel utilisateur
CYP
CYP AU-D21 Manuel utilisateur
CYP
CYP CDPS-41SQ Manuel utilisateur
CYP
CYP CDPS-U42HPIP Manuel d'installation
CYP
CYP OR-HD62CD Manuel utilisateur
CYP
CYP CPLUS-V4H1H Manuel utilisateur
CYP
CYP CPLUS-31PS Manuel utilisateur
CYP
CYP EL-42S Manuel utilisateur
CYP
CYP PU-8H8HBT Manuel utilisateur
CYP
CYP CDPS-U2HPIP Manuel utilisateur
CYP
CYP EL-C61C Manuel utilisateur
CYP
CYP CPRO-U4H1HFS Manuel utilisateur
CYP
CYP CED-1M Manuel utilisateur
CYP
CYP DCT-31 Manuel utilisateur
CYP
CYP CMIR-44 Manuel utilisateur
CYP
CYP CLUX-41W Manuel utilisateur
CYP
CYP CSC-5300 Manuel utilisateur
