CYP OR-HD62CD Manuel utilisateur

OR-HD62CD

6 x 2 UHD HDMI Switch with Audio De-Embedding

OPERATION MANUAL

DISCLAIMERS

The information in this manual has been carefully checked and is

believed to be accurate. CYP (UK) Ltd assumes no responsibility for any

infringements of patents or other rights of third parties which may result

from its use.

CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be

contained in this document. CYP (UK) Ltd also makes no commitment to

update or to keep current the information contained in this document.

CYP (UK) Ltd reserves the right to make improvements to this document

and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed,

stored in a retrieval system, or any of its part translated into any language

or computer le, in any form or by any means—electronic, mechanical,

magnetic, optical, chemical, manual, or otherwise—without express

written permission and consent from CYP (UK) Ltd.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate

this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside

the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if

it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sucient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

v1.00 20/01/2014 First release

v1.01 02/04/2014 Updated Introduction

v1.02 21/05/2014 4K Support Note

v1.03 08/08/2014 Updated RS-232 commands, Preview

and PIP Functions, DVI Compliance

v1.04 20/05/2016 Corrected Audio Tables Information

CONTENTS

1. Introduction...........................................6

2. Applications ...........................................6

3. Package Contents ..................................6

4. System Requirements ...........................6

5. Features..................................................7

6. Operation Controls and Functions .......8

6.1 Front Panel................................................... 8

6.2 Rear Panel...................................................10

6.3 OSD Menu ..................................................11

6.4 Remote Control........................................16

6.5 RS-232 Protocols.....................................17

6.6 RS-232 & Telnet Commands.................18

6.7 Telnet Control............................................21

6.8 Web GUI Control ......................................22

7. Connection Diagram .......................... 24

8. Specications...................................... 25

9. Acronyms............................................. 27

1. INTRODUCTION

The OR-HD62CD allows HDMI signals to be routed from any of the six

connected HDMI sources for display on two connected HDMI displays.

With fast switching technology this device dramatically improves the

sync time to the connected HDMI displays over traditional switchers.

In Matrix Mode, it allows any source to be routed independently to any

output. An on-board EDID management tool (via on screen display) can

be utilised for advanced audio and video signal management. In addition,

this switcher also includes a cutting edge Picture in Picture (PIP) preview

mode allowing the user to show 5 unselected HDMI sources in a row

of small windows overlaid on top of the primary selected HDMI source

video . In preview mode, both HDMI outputs show identical feeds. Further

features include the ability to de-embed Hi-Denition lossless audio via

a dedicated Optical output for each HDMI output, 4K resolution support,

and 3D signal support.

Control is via front panel buttons, IR remote control, RS-232, Telnet or IP

control for easy integration into control systems such as Control 4.

2. APPLICATIONS

Home Theater/Entertainment

Lecture Room/Hall Presentation

Show Room/Demo Room

Public Commercial Display

Information Board

3. PACKAGE CONTENTS

6 by 2 HDMI 4Kx2K Matrix

Remote Control with Battery

Left & Right Rack Ears

5V/2.6A DC Power Adaptor

IR Receiver Cable

Operation Manual

4. SYSTEM REQUIREMENTS

Input source equipments such as Blu-ray/DVD/PS3 player or Set-Top Box

and output HDMI TV/Display and or audio amplier with connection

cables.

5. FEATURES

HDMI, HDCP 1.1, DVI 1.0* compliant

Resolutions supported: HDTV - 480i to 1080p plus 1080p24fps, and

4K2K; PC - VGA to WUXGA;

High Denition audio supported: Dolby TrueHD, Dolby Digital Plus,

DTS-HD Master Audio + 7.1 Channel LPCM

RS-232, Telnet or IP Control, IR Remote Control (supplied), Web GUI

Control

Supports audio extraction from HDMI input to Optical output, input

audio sampling rate up to 192 kHz

Ability to switch between any two sources within 1 second

Built-in EDID Management

Supports 3D and 4K signals

Cutting edge Picture in Picture preview function:

When in Preview mode, the system will be treated as a Switcher (two

simultaneous HDMI outputs)

In Preview mode, the unit supports 'View All' (1 Main video source

and 5 Sub video sources) and 'PIP' (1 Main video source and 1 Sub

video source). 3D and 4Kx2K sources inputs are not supported for sub-

windows

Note: View All is TDM (Time Division Multiplexing display)

*Supports HDMI to DVI conversion when the HDMI source is not 'deep

colour' and has an RGB color space. Does not support HDMI to DVI

conversion of a HDMI source that is 'deep color' and has a colour space

that is YCbCr 444/422

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER

IN 1IN 2IN 3IN 4IN 5IN 6 MUTE CONFIRM

OUT A OUT B CANCEL

ENTER

PRESET

ALL

MODE

LOCK

1 2 5 6 8 1113 153

4 7 9 10 12 14

1POWER: Press this button to turn ON the device, the LED will

illuminate.

2IR Window: This IR Receiver receives the remote control signal from

the device's remote control only.

3IN 1~6: Press these IN buttons to select an input from the 6 input

sources.

4OUT A/B: Press these buttons in combination with with the IN

buttons to select an input source for an output display i.e. OUT A→ IN

1→CONFIRM or OUT B→IN 6→CONFIRM.

5MUTE: Press this button to mute video and audio on OUT A or B.

6CONFIRM: Press this button to conrm the selection of an IN and an

OUT button.

7CANCEL: Press this button to cancel the IN/OUT selection.

8ENTER: Press to conrm the selection.

9MENU: Press to enter into the menu.

10 +/-: Press these buttons to navigate up/down the menu.

11 PRESET: (PV MUTE: Preview ON/OFF)

¾When in Preview mode, press the button to turn ON/OFF the Sub

video windows.

¾When in Matrix mode, press “PRESET” to switch between Normal

and Preset mode.

9Normal mode:

Press OUT A or OUT B or ALL and then press IN 1~6 or

MUTE to select the input sources. After the selection,

press “CONFIRM” to conrm the selection or press“CANCEL”

to cancel the selection.

9Preset mode:

Press “PRESET”, the OLED menu will show Preset then

select IN 1~6. Preset 1~6 after the selection, press

“CONFIRM” to conrm the selection or press “CANCEL” to

cancel the selection.

12 All: (SWAP)

Press this button to select all outputs to display with an input source.

When in PIP mode, press to swap between Main video source and Sub

video source.

13 MODE: Press to switch between Preview or Matrix mode.

¾Preview mode: From MENU option select View All (1 Main

video sources and 5 Sub video sources) or PIP mode (1 Main

video sources and 1 Sub video sources).

Note: Under Preview mode, OSD display on output B only.

9View All: Press IN 1~6 or MUTE to select the Main channel.

From OLED menu select “Preview Position” for Sub

screens position.

Note: All sub screens will be displayed in order for about 0.5

second: Those screens that are not displayed will be frozen.

9PIP: Press OUT A (Main) or OUT B, then press IN1~6 or

MUTE to select Main or Sub video source. Press “ALL”

or Remote Control “ SWAP” to exchange Main/Sub

video source.

Note: When both Main and Sub select the same input source,

Sub will be muted.

¾Matrix mode: Press OUT A or OUT B or OUT A & B and then

press IN 1~6 or MUTE to select the input sources. After the

selection, press “TAKE” to conrm the selection or press

“CANCEL”to cancel the selection.

14 LOCK: Press this button to lock all button functions on the panel. Press

for 3 seconds to cancel the lock function.

15 LCM: Displays Input and Outputs selection and menu selection.

6.2 Rear Panel

CONTROLSERVICE

HDMI IN HDMI OUT S/PDIF OUT

123456AB RS232 IR IN DC 5V

1 4 5 6 7 8

2 3

1HDMI IN: Connect from source equipments such as Blu-ray/DVD/PS3

players, Set-Top-Box or any HDMI equipped source device for input

signal sending.

2HDMI OUT: Connect to HDMI TV/display or HD Amplier for output

image and or audio display.

3S/PDIF OUT: Connect to audio sound system or Amplier for digital

output sound.

4SERVICE: This slot is reserved for rmware update use only.

5CONTROL: Connect from PC/Laptop with active internet service for

Web GUI control with RJ-45 terminated cable.

6RS232: Connect from PC/Laptop for RS-232 command sending to

control the device.

7IR IN: Connect the IR Receiver included in the package for IR signal

receive from the included remote control.

8DC 5V: Connect the adaptor with power cord included in the package

and connect to AC wall outlet for power supply.

Table des matières

Autres manuels CYP Changer

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur