CYP CDPS-U42HPIP Manuel d'installation
CDPS-U42HPIP
4K UHD+4×2 HDMI Multiviewer
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2018 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
RDV1 10/11/17 Preliminary release
VS1 17/01/18 Final technical review
VS2 25/01/18 Page number correction
CONTENTS
1. Introduction......................................................1
2. Applications.....................................................1
3. Package Contents ..........................................1
4. System Requirements......................................2
5. Features............................................................2
6. Operation Controls and Functions.................3
6.1 Front Panel ................................................. 3
6.2 Rear Panel.................................................. 4
6.3 Remote Control......................................... 5
6.4 RS-232 Control ........................................... 6
6.5 Telnet Control ............................................ 7
6.6 RS-232 and Telnet Commands ................ 7
6.7 WebGUI Control ...................................... 20
6.7.1 Input ................................................ 21
6.7.2 Output............................................. 23
6.7.3 Windowing...................................... 25
6.7.4 Audio............................................... 30
6.7.5 EDID Settings................................... 32
6.7.6 User Congration ........................... 34
6.7.7 System Settings............................... 35
6.7.8 Admin - Logout .............................. 36
7. Connection Diagram ....................................37
8. Specications ................................................38
8.1 Technical Specications ........................ 38
8.2 Video Specications............................... 39
9. Acronyms .......................................................40
1
1. INTRODUCTION
This 4 by 2 Multiviewer is a high performance HDMI switch with
integrated scaling and multi-windowing technology. It is an ideal
solution for monitoring or displaying multiple sources simultaneously
for use in control rooms, conference rooms or classrooms. Video
resolutions up to 4K@60Hz and LPCM audio up to 7.1 channels at
192kHz are supported on both input and output and this unit is fully
compatible with the HDCP 1.x and 2.2 standards.
Any of 4 different HDMI sources may be displayed individually, full
screen, or they can be displayed using a variety of multi-window
modes including quad view and PiP with the output being sent to 2
mirrored HDMI outputs (4K@50/60Hz output supports quad view and
full screen only). Management of input/window routing, position and
sizing can be controlled easily by use of the front panel controls as
well as by WebGUI, RS-232, Telnet, and IR remote control options.
2. APPLICATIONS
• Entertainment Room & Home Theater
• Show Room & Demo Room
• Lecture Room & Hall Presentation
• Show Room & Demo Room
• Public Commercial Display
3. PACKAGE CONTENTS
• 1×4 by 2 HDMI Multiviewer
• 1×12V/3A DC Power Adapter
• 2×5-pin Terminal Block
• 1×Remote Control (CR-180)
• 1×Rackmount Ears (Set of 2)
• 1×Operation Manual
2
4. SYSTEM REQUIREMENTS
• HDMI source equipment such as media players, video game
consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors or audio
ampliers.
5. FEATURES
• HDMI inputs and outputs with 18Gbps (600MHz) 4K UHD support
• DVI 1.0 compatible with the use of an HDMI-DVI adaptor
• HDCP 1.x and 2.2 compliant
• Supports HD resolutions up to 4K@60Hz (4:4:4, 8-bit)
• 4 HDMI inputs and 2 mirrored HDMI outputs
• Seamless switching (no loss of sync to display) when switching
sources in both full screen and multi-window modes
• Supports PiP (Picture-in-Picture), side by side, 3+1 quad view, and
2×2 quad view display options with independent audio source
selection
Note: 4K@50/60Hz output supports 2×2 Quad View only and is
limited to 1080p/4K sources.
• Supports the ability to store a multi-window arrangement as a preset
that can be recalled later
• Each window can have a border with a selectable color
• Uploadable and freely positioned graphic logo support
Note: The logo and border features are not available when the
output is set to 4K@50/60Hz.
• Supports easy adjustment of window size, position and settings in
the PiP windowing mode via the WebGUI
• Matrix mode supports input and output resolutions up to
1080p@60Hz with a single shared audio source (Outputs are
mirrored at higher resolutions)
• Controllable via front panel buttons, WebGUI, Telnet, RS-232, and IR
remote
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER
UHD 4X2 MATRIX / PIP SCALER WITH FREE WINDOWS
A
B
IN 1 IN 2 IN 3 IN 4
MATRIX
1234
MULTI VIEW
WINDOW SOURCE SELECT
W1 W2 W3 W4
1234
12
34
2
1
12
1
2
3
4
MENU LOCK
ENTER PRESET
+
-
1 2 53
4 6
7 8 10 11
9
1POWER: Press this button to power the unit on (green LED) or place
it into stand-by mode (red LED).
2IR WINDOW: Accepts IR signals from the included IR remote for
control of this unit only.
3MATRIX A/B IN1~IN4: These input selection buttons behave
differently depending on the current input and output resolutions
in use.
AAll inputs and outputs are below 4K: Press any of these buttons to
seamlessly switch to the selected input (IN1~IN4)for display on the
associated output (A or B).
BAny input or output is 4K: Press any of these buttons to seamlessly
switch to the selected input (IN1~IN4) for display on both outputs
simultaneously.
Note: Audio for both outputs will follow the most recently selected
input (from A or B) in both modes.
4MULTIVIEW: Press any of these buttons to switch immediately to the
corresponding Multiview output mode.
5WINDOW SOURCE SELECT: Press these buttons to sequentially switch
through the available inputs for each window in Multiview output
modes.
6MENU: Press to enter the LCD menu, or to back out from menu
Items.
7ENTER: Press to conrm a selection within the LCD menu or to go
deeper into a menu item.
8 + & −: Press to move up and down or adjust selections within
menus.
9LOCK: Press to lock all button functions on the front panel. Press the
4
button again to release the lock function. The LCD will display a
“Lock” message when the function is active.
10 PRESET: Press this button to switch between the “Preset Load” and
“Preset Save” modes. Pressing the button a 3rd time exits the Preset
menu.
APreset Save: When in “Preset Save” mode, pressing the “Enter”
button will save the currently displayed window layout.
BPreset Load: When in the “Preset Load” mode, pressing the “Enter”
button will load the previously saved window layout.
Note: The audio selection is not saved as a part of the preset, only
the window layout.
11 LCD WINDOW: Displays the unit’s menu, settings, and information.
6.2 Rear Panel
DC 12V
CONTROL SERVICE
GND
TX
RX
RTS
CTS
COM
G
L/R OUT
-
+
-
+
AB
HDMI OUT
1234
HDMI IN
1 2 4
3
5 6 7
1HDMI IN 1~4: Connect to HDMI source equipment such as media
players, game consoles or set-top boxes. DVI source equipment
may be connected by using an HDMI to DVI adapter.
2HDMI OUT A~B: Connect to HDMI TVs, monitors or ampliers for
digital video and audio output. DVI display equipment may be
connected by using HDMI to DVI adapter.
3L/R OUT: Connect to powered speakers or an amplier using a 5-pin
adapter cable for balanced stereo analog audio output.
Note: Only LPCM 2.0 sources are supported. Bitstream audio
sources will be muted automatically.
4COM: Connect directly to a PC, laptop or other serial control
device with a 3-pin adapter cable to send RS-232 commands to
control the unit.
5CONTROL: Connect directly, or through a network switch, to your
PC/laptop to control the unit via Telnet/WebGUI.
6SERVICE: This slot is reserved for rmware update use only.
5
7DC 12V: Plug the 12V DC power adapter into the unit and connect
it to an AC wall outlet for power.
6.3 Remote Control
1POWER: Power on the machine or enter
to standby mode.
2INFO: Display the current status/
information of the unit.
3A1~A4 & B1~B4: (Matrix Selection)
AWhen all inputs and outputs are below
4K: Press any of these buttons to
seamlessly switch to the selected input
(1~4) for display on the associated
output (A or B).
BWhen any input or output is 4K: Press any
of these buttons to seamlessly switch to
the selected input (1~4) for display on
both outputs simultaneously.
Note: Audio for both outputs will follow the most recently selected
input (from A or B) in both modes.
4MV1~MV4: (Multiview Selection) Press these buttons to switch
immediately to the corresponding Multiview output mode.
MV1: Switch to 2×2 quad view mode.
MV2: Switch to the 3+1 quad view mode.
MV3: Switch to the side-by-side view mode
MV4: Switch to PiP view mode.
5MATRIX/MULTIVIEW: Press to toggle between the Matrix and
Multiview modes.
6LOCK: Press to lock all button functions on the front panel. Press the
button again to release the lock function.
7ARROWS (///) & OK: Press the arrow buttons to navigate
the LCD menu. Press the “OK” button to conrm a selection or to
go deeper into a menu item.
8MENU: Press to enter the LCD menu.
INFO POWER
A1 B1
A2 B2
A3 B3
A4 B4
MV1
MV2
MV3
MV4
LOCK MATRIX/
MULTI VIEW
EXIT MENU
OK
SAVE
PRESET
W1
W2
W3
W4
SOURCE
MUTE
UP
DOWN
AUDIO
CR-180
2
3
11
6
9
10
1
4
5
7
8
12
Table des matières
Autres manuels CYP Changer
CYP
CYP CED-S11 Manuel utilisateur
CYP
CYP PUV-2608TX Manuel utilisateur
CYP
CYP CPRO-3D41GAME Manuel utilisateur
CYP
CYP CLUX-41AP Manuel utilisateur
CYP
CYP AU-D41 Manuel utilisateur
CYP
CYP CED-1M Manuel utilisateur
CYP
CYP DCT-17 Manuel utilisateur
CYP
CYP CFSW-51MHL Manuel utilisateur
CYP
CYP EL-8100V Manuel utilisateur
CYP
CYP OR-88U-4K22 Manuel utilisateur
CYP
CYP DCT-31 Manuel utilisateur
CYP
CYP EL-41S-4K22 Manuel utilisateur
CYP
CYP PU-1H2HBTE Manuel utilisateur
CYP
CYP CPLUS-V4H1H Manuel utilisateur
CYP
CYP EL-42HEAC Manuel utilisateur
CYP
CYP CDPS-41SQN Manuel utilisateur
CYP
CYP EL-21SY Manuel utilisateur
CYP
CYP CLUX-4S2 Manuel utilisateur
CYP
CYP CPLUS-401V Manuel utilisateur
CYP
CYP CED-1M Manuel utilisateur
