ZALMAN CNPS7700 LED Manuel utilisateur

* Please read before installation.

http://www.zalman.co.kr http://www.zalmanusa.com

Intel

Dual Core Pentium / Pentium 4

Socket 775 CPU

Grip (S-Type)

Grip (L-Type)

Inner Hole

Grip (L-Type)

Outer Hole

Intel Pentium 4

Socket 478 CPU

AMD Sempron/AMD64

(Athlon 64 X2/Opteron/Athlon 64)

Socket 754/939/940 CPU

CNPS7700 LED

(English version)

All manuals and user guides at all-guides.com

all-guides.com

※

The specifications of any product may change without prior notice to improve performance.

Fan

Clip

Fan Fixing Screw

Grip (S-Type)

Grip (L-Type)

Fan Support Fixing Screw

Fan Support

FHS

1. Features

2. Specifications

3. Exploded Vie

1) Pure copper and/or pure aluminum ase materials ensure excellent heat dissipation.

2) Supports Intel Dual Core Pentium / Pentium 4 (Socket 775), Intel Pentium 4 (Socket 478), AMD Athlon

64 X2 Dual Core, Sempron / AMD64 (Socket 754/939/940) for road compati ility.

3) The large 120mm fan inside the FHS maximizes cooling performance y providing sufficient airflow

even at low fan speed.

4) The large 120mm fan provides air flow over a large area, cooling not only the CPU, ut the VGA card,

North ridge, FET, and RAM as well.

5) The high intensity red LEDs will operate with sufficient rightness even in low operating voltage.

6) The adjusta le fan speed controller (FAM MATE 2) ena les control of noise and fan performance.

2) FAN MATE 2

- Output Voltage : 5V ~11V 2%

- Power Consumption : 6W or lower

(Note 1) The maximum weight for a cooler is specified as 450g for Intel Socket 775/478 and AMD Socket

754/939/940. Special care should e taken when moving a computer equipped with a cooler

which exceeds the relevant weight limit. Zalman is not responsi le for any damage that occurs

when moving a computer.

(Note 2) The cooler fan operates at 2,300rpm if connected directly to the mother oard’s power connector

without the use of FAN MATE 2.

(Note 3) Noise measured 1m distance away from source.

1) ooler ( NPS7700 LED)

CNPS7700-AlCu LED CNPS7700-Cu LED

Model

Spec.

Materials

Weight

Thermal Resistance

Dimensions

Dissipation Area

Bearing Type

Fan Speed

Noise Level

Input Voltage

Pure copper and pure aluminum

600

(1)

0.19 ~ 0.28 ℃/W

918

(1)

0.17 ~ 0.24 ℃/W

136 (L) X 136 (W) X 67 (H) mm

3,268 ㎠

2 Ball-Bearing

1,000 ~ 2,000rpm ± 10%

22.7 ~ 37.1dBA ± 10%

5 ~ 12V

All manuals and user guides at all-guides.com

※

The specifications of any product may change without prior notice to improve performance.

󱆍

󱆎

󱆏

❿

❾

❶

❸

❺

❹

❻

❽

❼

󱆌

󱆐

❷

󳣍Korean Patent No. 389257

󳣍Korean Patent Design No. 327440-3

󳣍Parents pending in over 20 nations around the world, including the USA, EU, and Japan

4. Patents

Precautions

1) Keep the product away from children.

2) Check to see that all components are present, and check the condition of the product and its components efore

installation. If there is any pro lem, contact the place of purchase for a replacement.

3) If excessive force is exerted on the fan, the fan may malfunction and result in damage to the product and/or the

computer.

4) Do not insert your finger into the fan while it is operating.

Disclaimer) Zalman Tech Co., Ltd. is not responsi le for any damages due to external causes, including ut not

limited to, improper use, pro lems with electrical power, accident, neglect, alteration, repair,

improper installation, or improper testing.

1) Common Components

❶

FHS Assem ly (CNPS7700 LED)

❷

Four (4) Grips (2 each for S-Type and L-Type)

❸

Four (4) Bolts (for installing the FHS)

❹

Thermal Grease

❺

Fan Speed Controller (FAN MATE 2)

❻

Dou le - sided Tape (for installing FAN MATE 2)

❼

Ca le for FAN MATE 2

❽

User’s Manual (in English and Korean)

5. Components

2) Components for Intel Dual Core Pentium/Intel

Pentium 4 (Socket 775)

❾

One (1) Clip Support for Socket 775

❿

One (1) Backplate for Socket 775

󱆌

Four (4) Clip Support Fixing Bolts

Components for Intel Pentium 4 (Socket 478)

󱆍

Two (2) Clip Supports for Socket 478

Components for AMD Sempron / AMD64 (Socket 754/939/940)

󱆎

Two (2) Nipples

󱆏

One (1) Backplate for AMD64

󱆐

One (1) set of Washers

All manuals and user guides at all-guides.com

※

The specifications of any product may change without prior notice to improve performance.

6. Compatible CPUs

1) Intel Dual ore Pentium / Pentium 4 - Socket 775

All PUs conforming to Socket 775 platform

Caution)

①No components higher than 39mm (possi le examples :

PSU, graphics card, RAM etc.) should e present within

a 68mm radius from the center of the CPU.

②For more information, please visit Zalman’s we site

(http://www.zalman.co.kr) and click on the links of

"CNPS7700 Compati le Socket 775 Mother oards List".

2) Intel Pentium 4 - Socket 478

All PUs conforming to Socket 478 platform

Caution)

①No components higher than 39mm (possi le examples : PSU, graphics card, RAM etc.) should e present

within a 68mm radius from the center of the CPU.

②

For Socket 478, as shown in Figure 2, a mother oard that is not compliant with the "10.2mm Mother oard

component height restriction" standard, introduced y Intel, may create interference etween components

and the grip of CNPS7700 LED. Please do not install the CNPS7700 LED if this interference is o served.

③

For more information, please visit Zalman’s we site (http://www.zalman.co.kr) and click on the links of

"Compati ility etween CNPS7700 and Socket 478 Pentium 4 Mother oards".

3) AMD Sempron / AMD64 - Socket 754/939/940

All

PUs conforming to Socket 754/939/940 platform

Caution)

①No components higher than 39mm (possi le examples :

PSU, graphics card, RAM etc.) should e present within a

68mm radius from the center of the CPU.

②For more information, please visit Zalman’s we site

(http://www.zalman.co.kr) and refer to “CNPS7700

Compati le Socket 754/939/940 Mother oards List” link.

10.2mm Mother oard component height restriction

4mm

Grip

Mother oard

Component

Grip

Mother oard Component

Figure 1

ompatible

Figure 2

Not ompatible

All manuals and user guides at all-guides.com

※

The specifications of any product may change without prior notice to improve performance.

Clip Support Fixing Bolt

Socket Lever Hinge

Lever Slot

Socket Lever

Clip Support for Socket 775

Mother oard

Backplate for Socket 775

Backplate Support

CPU (IHS)

Bolt Grip (S-Type)

Grip (S-Type)

Clip Support for

Socket 775

Socket

775

478

754/939/940

Gr p

S - Type

L - Type

Hole

Inner Hole

Outer Hole

7. Installation

※

CNPS7700 LED must e used with a specific grip for

each CPU socket. Refer to the ta le on the right

to choose the correct grip.

1) Intel Dual ore Pentium/Intel Pentium 4 - Socket 775

①①Installation of lip Support for Socket 775

Align the clip support for socket 775 and the ackplate for socket 775 with the mounting holes on the mother oard

and fasten them together using the clip support fixing olts. The lever slot on the clip support should e properly

oriented on the hinged side of the socket lever when installing.

※The ackplate support is used for the convenience of installation. You can remove it if it is not deemed necessary.

②②Thermal Grease Application

Clear off particles and residue from the top of the

CPU then spread a generous amount of the included

thermal grease thoroughly on top of the CPU.

※Unlike the flat-milled ase of the FHS, the top surface of the LGA775 CPU may have minute dips and peaks

causing pockets of non-contact etween the FHS and CPU. Please apply a generous amount of thermal grease

on the top of the CPU.

③③Installation of Grips and Bolts

Interlock the S-type grips with the clip. Insert the two

olts into the holes of the grips.

④④FHS Placement

Set the FHS at the center of the CPU. Screw the olts

in slightly, then tighten each olt a few turns at a time while

alternating etween the two until the Grips are completely

pressed against the Clip Support.

⑤⑤onnect Power (Use FAN MATE 2)

◆Please refer to FAN MATE 2 Installation and Usage on page 7.

Thermal Grease

All manuals and user guides at all-guides.com

※

The specifications of any product may change without prior notice to improve performance.

②②

Installation of lip Supports for Socket 478

Install the clip supports for socket 478 on oth sides

of the retention guide as shown in the diagram.

③③Installation of Grips and Bolts

Interlock the L-type grips with the clip. Insert the two olts

into the inner holes of the grips.

④④

FHS Placement

Set the FHS at the center of the CPU. Screw the olts

in slightly, and then tighten each olt a few turns at a

time while alternating etween the two until the Grips

are completely pressed against the Clip Support.

Retention Guide

Clip Support for Socket 478

󳦈

󳦇

󳦊

⑤⑤onnect Power (Use FAN MATE 2)

◆Please refer to FAN MATE 2 Installation and Usage on page 7.

Bolt Grip (L-Type)

Inner Hole

Grip (L-Type)

Clip Support for

Socket 478

2) Intel Pentium 4 - Socket 478

①①

Thermal Grease Application

Clear off particles and residue from the top of the

CPU then spread a thin layer of the included thermal

grease thoroughly on top of the CPU.

CPU (IHS)

Thermal Grease

All manuals and user guides at all-guides.com

all-guides.com

※

The specifications of any product may change without prior notice to improve performance.

①①

Nipple Installation

Place a small washer on the mother oard. Then, put a nipple over it and fasten the nipple until the

Backplate for AMD64 is firmly attached to the mother oard on the opposite side of the CPU.

* A Retention Guide is not necessary for installing CNPS7700 LED on Socket 754/939/940.

③③Installation of Grips and Bolts

Interlock the L-Type grips with the clip. Insert the two olts

into the outer holes of the grips.

④④

FHS Placement

Set the FHS at the center of the CPU. Screw the olts

in slightly, and then tighten each olt a few turns at a

time while alternating etween the two until the Grips

are completely pressed against the Nipples.

⑤⑤onnect Power (Use FAN MATE 2)

◆Please refer to FAN MATE 2 Installation and Usage on page 7.

②②

Thermal Grease Application

Clear off particles and residue from the top of the

CPU then spread a thin layer of the included thermal

grease thoroughly on top of the CPU.

Bolt Grip (L-Type)

Outer Hole

Grip (L-Type)

Nipple

3) AMD Sempron/AMD64 - Socket 754/939/940

CPU (Lid)

Thermal Grease

Backplate for AMD64

Nipple

Mother oard

Small Washer

All manuals and user guides at all-guides.com

※

The specifications of any product may change without prior notice to improve performance.

Fan Connector

(CNPS7700 LED)

Mother oard

Dou le-sided Tape

FAN MATE 2

6-Pin Connector

※FAN MATE 2 Installation and Usage

1) Installing FAN MATE 2 on the Inside of the System 2) Installing FAN MATE 2 on the Outside of the System

Connect the appropriate 3-pin connector on the

ca le to the mother oard fan header and the

CNPS7700 LED’s fan connector.

Pull the 6-pin connector out of the system through

the ack and connect it to FAN MATE 2, which

should e installed on the case using the included

dou le-sided tape.

◆

Fan speed can e controlled with the use of FAN MATE2. Turning the speed control kno in the clockwise

direction will increase the fan speed, and turning the speed control kno in the counter-clockwise direction will

decrease the fan speed.

Note) FAN MATE 2 has een specifically designed for the fan of this product. Zalman Tech Co., Ltd. is not

responsi le for any damage to systems or CPUs caused y using it with other types of fans.

8. Notes on Usage

1) hecking PU ompatibility

Please refer to “Compati le CPUs” on page 3 to confirm that your CPU is compati le efore using the CPU cooler.

2) autions During Booting

When ooting the computer, it may automatically power down after an alarm sound y a system

monitoring program to indicate that the CPU fan is rotating slowly. If this happens, turn the speed

control kno fully clockwise to increase the fan speed. Then set ‘CPU Fan Detected’ to ‘Disa led’ in

BIOS settings, or set the slowest rotational speed of the CPU fan in the system monitoring program to

less than or equal to 900rpm.

Note) Some mother oards do not oot if the rotational speed of the CPU fan is elow a certain

rpm. If the BIOS settings are updated, Silent Mode can e used. For more information on

updating your BIOS, please refer to your mother oard manufacturer's we site. Disa ling

CPU fan speed detection in BIOS settings does not affect computer performance.

3) Overclocking

The fan should e set to Normal Mode if Overclocking.

(Zalman Tech Co., Ltd. is not responsi le for any damage resulting from CPU Overclocking.)

All manuals and user guides at all-guides.com

※

The specifications of any product may change without prior notice to improve performance.

11.

Home Theatre PC Enclosures

TNN Computer Enclosures are the world’s first environment-friendly noiseless computer enclosures

that operate without the use of a fans. TNN Computer Enclosures use the aluminum enclosure itself

as a heatsink. They are ideal for environments that require silence, as well as for home theatre

systems and multi-media systems.

The HD160 is designed for ultra quiet home theatre

PC operation, utilizing optimized ventilation and

anti-vi ration reinforcements, making it ideal for

environments that require silence such as living

rooms, edrooms, educational facilities, and offices.

For more information, please visit our website.

10.

TNN (Totally No Noise) Computer Enclosures

TNN 300 TNN 500AF

HD160

The use of Zalman's Noiseless Power Supplies, Fanless North ridge Coolers, Heatpipe HDD

Coolers, Case Fans, VGA Coolers and Multi-Fan Controllers will allow you to maintain sta le

performance and a noiseless environment.

9. Zalman Computer Noise Prevention System

Noiseless Power Supply Fanless Northbridge Cooler Heatpipe HDD Cooler

Noiseless Case Fan Ultra Quiet VGA Cooler Multi - Fan Controller

All manuals and user guides at all-guides.com

Autres manuels pour CNPS7700 LED

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ZALMAN Matériel informatique

ZALMAN

ZALMAN Optima CNPS8X Manuel utilisateur

ZALMAN

ZALMAN CNPS9500 AT Manuel utilisateur

ZALMAN

ZALMAN CNPS8000B Manuel utilisateur

ZALMAN

ZALMAN ZM80C Manuel utilisateur

ZALMAN

ZALMAN ZM-MFC1 Combo Manuel utilisateur

ZALMAN

ZALMAN CNPS8700 NT Manuel utilisateur

ZALMAN

ZALMAN RESERATOR1 V2 Guide de démarrage rapide

ZALMAN

ZALMAN CNPS2005-Plus Manuel utilisateur

ZALMAN

ZALMAN CNPS20LQ Manuel utilisateur

ZALMAN

ZALMAN CNPS9700 LED Manuel utilisateur

ZALMAN

ZALMAN ZM80D-HP Manuel utilisateur

ZALMAN

ZALMAN CNPS6000-Al Manuel utilisateur

ZALMAN

ZALMAN CNPS9700 LED Manuel utilisateur

ZALMAN

ZALMAN ZM80C-HP Manuel utilisateur

ZALMAN

ZALMAN CNPS8700 NT Manuel utilisateur

ZALMAN

ZALMAN ZM80D-HP Manuel utilisateur

ZALMAN

ZALMAN CNPS8000A Manuel utilisateur

ZALMAN

ZALMAN OPTIMA II CNPS10X Manuel utilisateur

ZALMAN

ZALMAN CNPS2X Manuel utilisateur

ZALMAN

ZALMAN CNPS7700 LED Manuel utilisateur

ZALMAN

ZALMAN CNPS11X Extreme Manuel utilisateur

ZALMAN

ZALMAN ZM-GWB3 Manuel utilisateur

ZALMAN

ZALMAN Z9 series Manuel utilisateur

ZALMAN

ZALMAN VF900-Cu Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur