PEERLESS Solid-Point PLB 1 Mode d’emploi
1 of 5 ISSUED: 04-22-03 SHEET #: 201-9046-4 02-25-08
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
Model: PLB 1
Installation and Assembly - Solid•Point™Plasma Ceiling Mount
Read instruction sheet before you start
installation and assembly. Maximum Load Capacity:
300 lb (136 kg)
Applications
Installation of PLP adapter plate................................. Step 3
Installation of LC adapter plate ................................... Step 4
EXTENSION COLUMN
(SOLD SEPARATELY)
• Failure to install M5 penta-pin screw (D) can cause the mount to fall!
WARNING
2 of 5 ISSUED: 04-22-03 SHEET #: 201-9046-4 02-25-08
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
A
Fasteners
CDEF
G
I
H
B
J
Before you start check the parts list to insure all of the parts shown are included.
Parts List
Description Qty. Part Number
Ainterface bracket 1 200-1090
Btilt bracket 2 200-1552
CM10 x 1.5 x 15 mm penta-pin™screw 16 520-9263
DM5 x .8 x 10 mm self-tapping penta-pin screw 1 505-9010
E#8 x 3/8" truss head sheet metal screw 1 520-1078
FM10 x 2" penta-pin tool 1 520-9260
GM5 x 1" penta-pin tool 1 520-9249
H2.125" ID x 2.875" OD x .062" H fiber washer 1 540-9432
Iretaining collar 1 1800-375
JM5 x .8 x 8 mm phillips screw 8 520-1167
Note: Some parts may appear slightly different than illustrated.
3 of 5 ISSUED: 04-22-03 SHEET #: 201-9046-4 02-25-08
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
Note: Hole with notch indicates bottom of interface bracket as shown in detail 1.
Insert interface bracket (A) onto extension column (sold separately) and attach using fiber
washer (H) and retaining collar (I) as shown (right).
IMPORTANT: Retaining collar (I) requires a M5 x 10 mm penta-pin screw (D). Carefully
thread retaining collar (I) onto end of extension column. Tighten retaining collar (I) at least
four complete turns ending with one of the small holes aligned with slot in the end of exten-
sion column. Insert and tighten M5 x 10 mm penta-pin screw (D) using M5 x 1" penta-pin
tool (G) where shown in Illustration A.
Illustration A
Detail 1
Screw eight M10 x 15 mm penta-pin screws (C) into holes of interface bracket (A) leaving approximately 1/4" of
exposed thread as shown below and in detail 2.
Detail 2
C
1/4"
C
I
H
A
A
D
EXTENSION
COLUMN
(SOLD
SEPARATELY)
SLOT
I
EXTENSION
COLUMN
A
A
A
• M5 penta-pin screw (D) is self tapping and may be
hard to get started but is essential to this installation.
Failure to install this screw can cause the mount to
fall!
WARNING
4 of 5 ISSUED: 04-22-03 SHEET #: 201-9046-4 02-25-08
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
NOTE: Refer to adapter plate instruction sheet for attachment of adapter
plate to screen before proceeding with step 3. If your adapter plate has an
aluminum race attached to it, remove before proceeding and discard race. It is
not used with this product.
Attach tilt bracket (B) to each adapter plate using four M10
x 15 mm penta-pin screws (C). Tighten M10 x 15 mm
penta-pin screws (C) using M10 x 2" penta-pin tool (F).
B
ADAPTER
PLATE
ADAPTER
BRACKET
B
Attach tilt bracket (B) to adapter bracket using four M5 x 8 mm phillips screws (J).
Note: Do not use M5 x 6 mm screws that are included with the adapter bracket.
Note: Screen and adapter
plate may appear different
thanillustrated.
SCREEN
NOTE: Refer to adapter plate instruction sheet for attachment of adapter
plate to screen before proceeding with step 4. If your adapter plate has an
aluminum race attached to it, remove before proceeding and discard race. It is
not used with this product.
Note: Screen and adapter
plate may appear different
thanillustrated.
Skip to step 5.
J
Installation of PLP Adapter Plates
Installation of LC Adapter Plates
C
5 of 5 ISSUED: 04-22-03 SHEET #: 201-9046-4 02-25-08
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
Hang each plasma screen on interface bracket (A) as shown in Illustration B. Adjust tilt as desired for each
screen and tighten eight M10 x 15 mm penta-pin screws (C) on interface bracket (A) using M10 x 2" penta-pin
tool (F).
E
After both screens are installed, lock interface bracket (A) into
place using one #8 x 3/8" truss head sheet metal screw (E) as
shown in Illustration C and detail 3.
Note: Make sure both screens are installed properly before
locking interface bracket (A) into place.
Illustration B
Illustration C
A
Detail 3
C
©2007,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Table des matières
Autres manuels PEERLESS Support et étagère
PEERLESS
PEERLESS HCACC502 Manuel utilisateur
PEERLESS
PEERLESS Paramount PC930A Mode d’emploi
PEERLESS
PEERLESS PLA 60-UNL Mode d’emploi
PEERLESS
PEERLESS WMJ 018 Mode d’emploi
PEERLESS
PEERLESS SAL730P Mode d’emploi
PEERLESS
PEERLESS VPM 25-J Mode d’emploi
PEERLESS
PEERLESS LCT-202 Mode d’emploi
PEERLESS
PEERLESS SUF650P and assembly Mode d’emploi
PEERLESS
PEERLESS IMC 18 Mode d’emploi
PEERLESS
PEERLESS LCC 18 Mode d’emploi
PEERLESS
PEERLESS WSP820 Mode d’emploi
PEERLESS
PEERLESS CMJ 470W Mode d’emploi
PEERLESS
PEERLESS VPM 25-W Mode d’emploi
PEERLESS
PEERLESS Paramount PF660 Mode d’emploi
PEERLESS
PEERLESS PLT BLK Mode d’emploi
PEERLESS
PEERLESS PLC Mode d’emploi
PEERLESS
PEERLESS A100IWBMOUNT Mode d’emploi
PEERLESS
PEERLESS DS246 Mode d’emploi
PEERLESS
PEERLESS PJF2-UNV Mode d’emploi
PEERLESS
PEERLESS SF630-AB Mode d’emploi
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
