PEERLESS LCT-202 Mode d’emploi
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 07-31-09 SHEET #: 090-9183-2 10-29-09
Max Load Capacity: 25 lb (11.3 kg) per arm
Installation and Assembly:
Dual-Screen Desktop Mount for 10" to 20" LCD Monitors
Models: LCT-202
ISSUED: 07-31-09 SHEET #: 090-9183-2 10-29-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
2 of 7
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Cable Management ................................................................................................................................................................4
Attaching VESA Plates to Display ..........................................................................................................................................5
Attaching Display to Dual Arm Assembly................................................................................................................................6
Attaching Dual Arm Assembly to Base ...................................................................................................................................7
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
WARNING
ISSUED: 07-31-09 SHEET #: 090-9183-2 10-29-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
3 of 7
Parts may appear slightly different than illustrated.
A
BC
D
E
F
G
H I M
JN
O
K
L
Description Qty. Part #
ADual arm column 1 AD19-T2-00
BVESA plate 2 VCUP-00-00
CColumn cover* 1 CLMC-05-00
DBase 1 BASE-02-00
EM6 flat washer 2 HWWA-M6-01
FM6 lock washer 2 HWLC-M6-01
GM6 hex head screw 2 HSHX-M6-25
Hadhesive cable anchors 2 HTWA-01-00
I#8 phillips self-tapping screw* 1 HSST-I8-75
JM10 flat washer* 1 HWWA-10-01
KM10 split lock washer* 1 HWLC-10-01
LM10 wingnut* 1 HNUT-10-01
Mrubber bumpers 3 HRBS-20-01
NM4 flat washer 8 HWWA-M4-01
OM4 lock washer 8 HWLC-M4-01
PM4 pan phillips head screw 8 HSPP-M4-16
Qcable ties 2 HTWR-01-00
R5 mm allen wrench 1 TAKY-05-01
*item attached to dual arm column (A)
Before you begin, make sure all parts shown are included with
your product.
Parts list
P
QR
ISSUED: 07-31-09 SHEET #: 090-9183-2 10-29-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
4 of 7
A
A
C
C
I
H
Q
I
Remove #8 self-tapping screw (I) using a phillips screw driver to unattach column cover (C) from dual arm column
(A). Insert cables into cavity of the dual arm column (A) as shown in gure 1.1 and reattach column cover (C) to
back of dual arm column (A) using #8 self-tapping screw (I).
NOTE: Be sure connectors are in their proper orientation. Allow enough cable slack to connect to display.
NOTE: Be sure all cables are free from interference and do not pinch power cables with column cover or fastener
as shown in detail 1.
Remove adhesive backing from cable anchors (H) and position onto back of dual arm column (A) as shown in
gure 1.2. Secure cables to arms using cable ties (Q).
CAVITY
1
Cable Management
DETAIL 1
g 1.1
g 1.2
CABLES
CABLES
ISSUED: 07-31-09 SHEET #: 090-9183-2 10-29-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
5 of 7
Attaching VESA Plates to Display
To prevent scratching the display, set a cloth on a at, level surface that will support the weight of the screen. Place
display face side down. If display has knobs on the back, remove them to allow the VESA plates to be attached.
Place VESA plates (B) on back of display.
Choose hole pattern as shown in detail 2. Attach VESA plates (B) to display using four M4 phillips screws (P), four
M4 lock washers (O), and four M4 at washers (N) as shown in gure 2.1.
• Tighten screws so VESA plates are rmly attached. Do not tighten with excessive force. Overtightening can cause
stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
DETAIL 2
P
B
O
N
2
g 2.1
ISSUED: 07-31-09 SHEET #: 090-9183-2 10-29-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
6 of 7
Attaching Dual Arm Assembly to Base
Attach VESA plates to dual arm column (A) using one M6 hex head screw (G), one M6 split lock washer (F) and
one M6 at washer (E) per arm as shown below. Tighten fasteners using 5 mm allen wrench (R).
Unscrew M10 fasteners (J, K, and L) from threaded rod.
Attach dual arm column (A) to base (D) by hand threading M10 washer (J), M10 split lockwasher (K), and M10
wingnut (L) through arm assembly threaded rod as shown in gure 4.1. Ensure that all fasteners are tightened
securely.
• Be sure display is unplugged from any electrical outlet while assembling dual stand.
• Tighten screws so adapter brackets are rmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
WARNING
G
A
F
E
3
4
g 4.1
JK
L
THREADED ROD
ISSUED: 07-31-09 SHEET #: 090-9183-2 10-29-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
7 of 7
Apply rubber bumpers (M) to bottom of base as shown in gure 5.1.
Carefully lift the full assembly to its upright position as shown in gure 5.2.
NOTE: Be sure assembly rests on a at, level surface to prevent the displays from tipping.
NOTE: Leave a small gap between the displays to allow for horizontal pivot adjustment as shown below.
• Use two displays with this mount. Product may fail and damage property if not installed correctly.
WARNING
5
g 5.1 g 5.2
M
© 2009, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Table des matières
Autres manuels PEERLESS Support et étagère
PEERLESS
PEERLESS SOLID-POINT PLCM1CP Mode d’emploi
PEERLESS
PEERLESS Vision-Point LCV 100 Mode d’emploi
PEERLESS
PEERLESS HCACC503 Manuel utilisateur
PEERLESS
PEERLESS Vision Point LCFS 100 Mode d’emploi
PEERLESS
PEERLESS SmartMount SP850-UNL Mode d’emploi
PEERLESS
PEERLESS IB40 Mode d’emploi
PEERLESS
PEERLESS PARAMOUNT PRA2X2 Manuel utilisateur
PEERLESS
PEERLESS PLC Mode d’emploi
PEERLESS
PEERLESS DS495 Mode d’emploi
PEERLESS
PEERLESS PANA-85WM Mode d’emploi
PEERLESS
PEERLESS DS415 Mode d’emploi
PEERLESS
PEERLESS SA761PU Mode d’emploi
PEERLESS
PEERLESS SmartMount RTFPA45 Mode d’emploi
PEERLESS
PEERLESS ACC 604 Mode d’emploi
PEERLESS
PEERLESS Paramount PS200 Mode d’emploi
PEERLESS
PEERLESS A100IWBMOUNT Mode d’emploi
PEERLESS
PEERLESS WMJ 018 Mode d’emploi
PEERLESS
PEERLESS PLCM 3 Mode d’emploi
PEERLESS
PEERLESS PARAMOUNT PA730 Mode d’emploi
PEERLESS
PEERLESS Solid-Point PLCM 1 CP Mode d’emploi
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
