PEERLESS Smartmount ST670 Mode d’emploi

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED:11-7-07 SHEET#:202-9244-1

Installation and Assembly:

This product is UL Listed. It must be

installed by a qualified professional

installer.

SmartMount®Universal Tilt Wall Mount

for LCD and Plasma Flat Panel Screens

Features:

• Screen held only 3" from wall for a discreet installation

• Wall plate design allows for wall acces allowing multiple cable management options

• Universal tilt brackets easily hook onto wall plate for fast installation

• Adjustable up to 15° of forward tilt and up to -5° backward tilt for optimal viewing angle

• One-touchtiltforeffortlessadjustment

• Pre-tensioned universal tilt bracket allows for tilt angle adjustment in one easy motion.

• Easy grip handle locks the screen position into place

• Optional IncreLok feature offers fixed tilts at -5°, 0°, 5°, 10° and 15° increments

• Includes Sorted-For-You™ fastener pack for installation to wood studs, concrete, and cinder block

• Optionalhorizontaladjustmentofupto8"(dependingonscreenmodel)forperfectscreenplacement

• AvailableinBlackorSilver

Product is UL rated for screen size

range and load capacity per chart below

Model # Screen Size Range Max. UL Load Capacity

ST670, ST670P, ST670-S, ST670P-S 42''- 71'' 250 lb (113 kg)

ST680, ST680P, ST680-S, ST680P-S 61''- 102'' 350 lb (159 kg)

2 of 27 ISSUED:11-7-07 SHEET#:202-9244-1

NOTE: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

•studfinder("edgetoedge"studfinderisrecommended)

•phillipsscrewdriver

•drill

•1/4" bit for concrete and cinder block wall

•1/2" bit for metal stud wall

•5/32" bit for wood stud wall

•level

Table of Contents

Parts List..............................................................................................................................................................................3

Installation to Triple Wood Stud Wall ....................................................................................................................................5

Installation to Solid Concrete or Cinder Block .......................................................................................................................6

InstallingTiltBrackets...........................................................................................................................................................7

Installing Flat Panel Screen to Wall Plate.............................................................................................................................9

Accessories

•ACC615 - Metal Stud Fastener Kit (Metal Stud not

evaluatedbyUL)

•SCS222- SmartMount®Component Shelf

• Donot begin to install your Peerless product until you have read and understood the instructionsandwarnings

containedin this Installation Sheet. If you have any questions regarding any oftheinstructions or warnings, please

callPeerless customer careat 1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Makesurethatthesupporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

• Neverexceed the Maximum ULLoad Capacity.See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgeto edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrews firmly,but do not overtighten.Overtighteningcan damage the items,greatlyreducing their holding

power.

• Thisproduct was designed and intendedtobe mounted to the following supportingsurfaces checked below with the

hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-

ing surface, contact Peerless customer care at 1 800 865-2112.

• This product was designed to be installed on the following wall construction only;

WALLCONSTRUCTION ADDITIONALHARDWARE REQUIRED

xWoodStud None

xWoodBeam None

xSolidConcrete None

xCinderBlock None

MetalStud Do not attach except with Peerless accessory kit for metal studs;

Contact Customer Service for Peerless accessory kit for metal studs.

Brick ContactCustomer Service

Otheror unsure? ContactCustomer Service

WARNING

3 of 27 ISSUED:11-7-07 SHEET#:202-9244-1

AA BB DD FF

Adapter Bracket Fasteners

M4 x 25 mm (4)

504-1015

M4 x 12 mm (6)

504-9013 M5 x 12 mm (4)

520-1027

M5 x 25 mm (4)

520-9543

M6 x 12 mm (4)

520-1128

M6 x 25 mm (4)

520-1208

M8 x 16 mm (6)

520-9257

M8 x 40 mm (4)

520-1136

I.D. .34" (8.6 mm) (4)

540-1059

M6 x 20 mm (4)

520-9402 M6 x 30 mm (4)

510-9109

M8 x 25 mm (4)

520-1031 multi-washer(6)

580-1036

I.D. .22" (5.6 mm) (4)

540-1057

Partsmay appear slightly different than illustrated.

I.D. .35" (8.9 mm) (6)

5W1-035-X01

M10 x 15 mm (4)

520-1305

NOTE: The sorted-for-you™ fastener pack included was made specifically for your product and may not contain all components shown below.

Description Qty. Black Silver Black Silver

XX AA

wall plate 1 200-1901 200-4901 200-1901 200-4901

XX 200-1902 200-4902 200-1902 200-4902

XX BB 1 201-1475 201-4475 201-1476 201-4476

XX 201-1479 201-4479 201-1480 201-4480

XX CC 1 201-1473 201-4473 201-1474 201-4474

XX 201-1477 201-4477 201-1478 201-4478

XXXXDD 6 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

XXXXEE 6 590-0097 590-0097 590-0097 590-0097

XXFF 1 not included not included 560-1146 560-1146

#14 x 2.5" wood screw

alligator®anchor

4 mm allen wrench

ST670P, ST670P-S

ST680P, ST680P-S

left tilt bracket

right tilt bracket

ST670, ST670-S

ST680, ST680-S

Before you begin, make sure all parts shown are included with your product.

Parts List Non-Security Security

4 of 27 ISSUED:11-7-07 SHEET#:202-9244-1

M4 x 25 mm (4)

510-1082

M4 x 12 mm (6)

510-1079 M5 x 12 mm (4)

520-1064

M5 x 25 mm (4)

520-1122

M6 x 12 mm (4)

520-1050

M6 x 25 mm (4)

520-1211

M8 x 15 mm (6)

520-1068

M8 x 40 mm (4)

520-1152

M6 x 20 mm (4)

520-9554 M6 x 30 mm (4)

520-1067

M8 x 25 mm (4)

520-1101

M4 x 8 mm (4)

510-1005

SecurityAdapter Bracket Fasteners

multi-washer(6)

580-1036

I.D. .34" (8.7 mm) (4)

540-1059

I.D. .22" (5.6 mm) (4)

540-1057

M10 x 2" Penta-pinTM driver (1)

520-9260

M10 x 15 mm (4)

520-9263

I.D. .35" (8.9 mm) (6)

5W1-035-X01

NOTE: The sorted-for-you™ fastener pack included was made specifically for your product and may not contain all components

shown below.

5 of 27 ISSUED:11-7-07 SHEET#:202-9244-1

Installation to Triple Wood Stud Wall

fig. 1.1

CS = center of screen

(152 mm) 6"

(152 mm)

Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Useofanedge-to-edgestudfinderishighlyrecommended.Basedon their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen

center as shown in figure 1.1. Level plate, and mark the center of the six mounting holes. Make sure that the

mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the

wall plate is level, secure it using six #14 x 2.5" wood screws (DD) as shown in figure 1.2.

Skip to step 2.

• Installermust verify that the supporting surface will safelysupport the combined load of the equipment andallattached

hardwareandcomponents.

• Tightenwood screws so that wall plateisfirmly attached, but do not overtighten.Overtighteningcan damage the

screws,greatly reducing theirholding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovided is for attachment ofmount through standard thickness drywallor plaster into wood studs.Installers

areresponsible to providehardware for othertypesof mounting situations.

WARNING

2.5"

(65 mm)

fig. 1.2

STUD

6 of 27 ISSUED:11-7-07 SHEET#:202-9244-1

Installation to Solid Concrete or Cinder Block

1Make sure that wall plate (AA) is level, use it as a

template to mark four mountingholes. The top

mountingholeshould be 2.5" (65 mm) above the

desired screen center as shown in figure 1.1 on page

5. Drill four 1/4" (6 mm) dia. holes to a minimum depth

of 2.5" (65 mm). Insert anchors (EE) in holes flush with

wallasshown(right).Placewallplateoveranchors

and secure with #14 x 2.5" screws (DD). Level, then

tightenall fasteners.

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesurethatthesupporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

WARNING

CUTAWAY VIEW

INCORRECT

concrete

surface

Drill holes and insert anchors (EE).

CORRECT

Place plate (AA)over anchors (EE) and secure with screws (DD).

Tighten all fasteners.

wall

plate

plaster/

drywall

concrete wall plate concrete

plaster/

drywall

• Always attach concrete anchors directly to load-

bearingconcrete.

• Neverattach concreteanchors to concretecovered

withplaster,drywall, or other finishing material.If

mountingto concrete surfacescoveredwith a finishing

surfaceis unavoidable, thefinishingsurface must be

counterboredas shown below. Be sureconcrete

anchorsdo not pull away fromconcrete when tighten-

ing screws. If plaster/drywall is thicker than 5/8",

custom fasteners must be supplied by installer.

WARNING

• Tighten screws so that wall plate is firmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

solid concrete cinder block

7 of 27 ISSUED:11-7-07 SHEET#:202-9244-1

Attaching Tilt Brackets to Screen using Baffled Fastener Pack

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place

screenfacesidedown. Refertoscreenmanufacturers instructionsorcustomerservice, forremovinganyknobs, base,

cover,orscrew(s) ontheback ofthescreento preparemounting.These needtoberemoved toallowthe adapter

brackets to be attached. Select the small, medium, large or extra large screws from the baffled fastener pack then

attach tilt brackets to screen following figure 2.1 or 2.2.

NOTE: Be sure to attach tilt brackets with handle facing outward as shown below.

NOTE:Top and bottom mountingholes must be usedfor attachingbrackets.Middle holes should alsobeused where

thefasteners and screens allow. Verify that all holes are properly aligned,and then tighten screws using a phillips

screwdriver.

NOTES:

• Always use multi-washers when attaching tilt

brackets(BB andCC)to your screen when using

small, medium or large screws. No multi-washer is

requiredfor extra large(M8) screws.

• Usethe correspondinghole in the multi-washer

that matches your screw size as shown.

• Tightenscrews so adapter brackets are firmlyattached. Do not tighten with excessiveforce. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

MULTI-WASHER

MEDIUMHOLEFOR M5SCREWS

LARGE HOLE FOR M6 SCREWS

SMALL HOLE FOR M4 SCREWS

CENTERBRACKETSVERTICALLY

ON BACK OF SCREEN

HANDLEFACE

OUT

Note: "X"dimensions should be equal.

NOTE: For flat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.

Note: Slots in ST680, ST 680P, ST 680-S, and

ST680P-S are wider and requirethe use of the

M8 washer I.D. 8.9 mm.

8 of 27 ISSUED:11-7-07 SHEET#:202-9244-1

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/3

for ST670 models or www.peerlessmounts.com/4 for ST680 models for a full screen compatibility chart for this

mount.

Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown

below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten.

If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack.

Repeatforremaining mounting holes, level brackets and tighten screws.

NOTE: Spacersmaynot be used, depending upon the type of screen.

NOTE: If using M10 x 15 mm penta-pinTM screws, tighten screws with Penta-pinTM driver.

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/3

for ST670 models or www.peerlessmounts.com/4 for ST680 models for a full screen compatibility chart for this

mount.

Beginwithlongerlengthscrew, hand thread through multi-washer, adapter bracket and spacer in that order into

screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do

not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled

fastenerpack.Repeat for remaining mounting holes, level brackets and tighten screws.

NOTE: If using M10 x 15 mm penta-pinTM screws, tighten screws with Penta-pinTM driver.

For Flat Back Screen

For Bump-out or Recessed Back Screen

SCREEN

SCREW

ADAPTER

BRACKET

(BBor CC)

fig. 2.2

SPACER

ADAPTER

BRACKET

(BBor CC)

SCREEN fig. 2.1

SCREW

2-1

2-2

Ifyou have any questions,pleasecall Peerless customer careat 1-800-865-2112.

MULTI-WASHER

9 of 27 ISSUED:11-7-07 SHEET#:202-9244-1

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

• Always use an assistant or mechanical lifting equipment

to safely lift and position the flat panel screen.

• Donot tighten screwswith excessive force. Overtightening

can cause damage to mount. Tighten screws to 40 in. • lb

(4.5N.M.) maximum torque.

• Becareful not to pinch fingerswhenpushing screen from

the bottom.

For preset tilt angles use Increlok™ and for custom tilt

angleuseratchet handle.

INCRELOK™: The screen can be locked into a

pre-set tilt position of -5°, 0°, 5°, 10° or 15°. Use

locator hole to find tilt position hole and tilt screen to

align holes. Tighten IncreLok™ tilt locking screws on

both tilt brackets to lock tilt as shown in detail 2.

Ratchet Handle: Loosen ratchet handle (refer to step

3 for tension adjustment of handle). Push or pull from

top or bottom of screen to adjust tilt as shown in figure

4.1. The tilt can be adjusted to a maximum of 15°

forwardor 5°backward.

TensionAdjustment of Ratchet Handle:Adjust

tension in tilt brackets (BB & CC) by rotating ratchet

handle. NOTE:If obstructionprevents ratchet handle

fromrotating, pull handle out while turning will allow

handleto reposition without tightening. Release and

turn handle to tighten or loosen.

Mounting Screen: Ratchet handle must be in the up or

down position or interference will occur while hooking tilt

brackets to wall plate (AA). Slowly hook tilt brackets

(BB & CC)onto wall plate (AA) and swing screen down

as shown in fig. 3.1. Tilt bracket hooks must fully

engage wall plate as shown in detail 1. Using phillips

screw driver/allen wrench (FF), turn safety screws on tilt

brackets (BB & CC) clockwise till screw tip securely

contacts wall plate as shown in cross section.

Screen Adjustment: Screen can be adjusted

horizontally by loosening safety/security screws on tilt

brackets (BB & CC) three full turns.Adjust screen as

shown in figure 3.2. Tighten safety screws on tilt

brackets till screw tip securely contacts wall plate as

shown in cross section.

Removing Screen: To remove screen from mount,

loosen safety screws, swing screen away from mount,

and lift screen off of mount.

Mounting and Removing Flat Panel Screen

DETAIL 2

fig. 4.1

IncreLok™

TILTLOCKING

SCREW LOCATOR

HOLE

RATCHET

HANDLE

TILT

POSITION

HOLES

fig. 3.2

Adjusting the Tilt Angle of the Flat

Panel Screen

WARNING

fig. 3.1

RATCHET

HANDLE

SAFETY/

SECURITY

SCREW

DETAIL 1

BB &

CROSS SECTION

BB &

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED:11-7-07 SHEET#:202-9244-1

Características:

• Sostiene el televisor a sólo 3" de la pared para proporcionar una instalación discreta

• El diseño de la placa de pared permite acceso a la pared y brinda múltiples opciones para el manejo de cables

• Lossoportes inclinables universales se enganchan con facilidad a la placa de pared para proporcionar una instalación

rápida

• Inclinación ajustable hacia delante de hasta 15° y hacia atrás de hasta -5° para ver el televisor desde un ángulo óptimo

• Inclinación de un solo toque para permitir el ajuste sin esfuerzo

• Elsoporte inclinable universal preapretado permite ajustar el ángulo de inclinación con un solo movimiento sencillo

• La palanca de agarre fácil fija la posición de la pantalla con seguridad

• Lafunciónopcional IncreLok™ ofrece ángulos de inclinación predeterminados en incrementos de -5°, 0°, 5°, 10° y 15°

• IncluyeelpaquetedesujetadoresSorted-For-You™parainstalacionesen montantesde madera, concreto y bloques de

hormigónde escorias

• Ajuste horizontal opcional de hasta 8" (dependiendo del modelo de la pantalla) para la colocación perfecta de la pantalla

• Alaventa en color negro y plateado

Instalación y ensamblaje:

Soporte universal de pared SmartMount® con

capacidad de inclinación para pantallas planas

Ce produit est homologué UL. Il doit être

installé par u installateur

professionnel qualifié.

de modelo Gama de tamaño de las pantallas Capacidad de carga máxima de UL

ST670, ST670P, ST670-S, ST670P-S 42'' - 71'' 250 lb (113 kg)

ST680, ST680P, ST680-S, ST680P-S 61'' - 102'' 350 lb (159 kg)

El producto cuenta con una clasificación de UL para sostener pantallas de televisores de una gama de tamaños específicos y

proporcionar una capacidad de carga de _______ de acuerdo con la tabla de abajo.

Autres manuels pour Smartmount ST670

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels PEERLESS Support et étagère

PEERLESS

PEERLESS SUF640P and assembly Mode d’emploi

PEERLESS

PEERLESS Smartmount Mode d’emploi

PEERLESS

PEERLESS ACC605 Mode d’emploi

PEERLESS

PEERLESS SA761P Mode d’emploi

PEERLESS

PEERLESS PLA 60-UNL Mode d’emploi

PEERLESS

PEERLESS PJF2-UNV Mode d’emploi

PEERLESS

PEERLESS SF 24D Mode d’emploi

PEERLESS

PEERLESS Paramount PP730 and assembly Mode d’emploi

PEERLESS

PEERLESS IM760P Mode d’emploi

PEERLESS

PEERLESS WSP700 Mode d’emploi

PEERLESS

PEERLESS HDS-S Mode d’emploi

PEERLESS

PEERLESS DST940 Mode d’emploi

PEERLESS

PEERLESS IM740P Mode d’emploi

PEERLESS

PEERLESS SmartMount SA750P Mode d’emploi

PEERLESS

PEERLESS HL4UN-002 Mode d’emploi

PEERLESS

PEERLESS Paramount PA760 Mode d’emploi

PEERLESS

PEERLESS ESA746PU Mode d’emploi

PEERLESS

PEERLESS LCC 18-C Mode d’emploi

PEERLESS

PEERLESS ACC 314 Mode d’emploi

PEERLESS

PEERLESS WSP700 Mode d’emploi

PEERLESS

PEERLESS PLAV 70 Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PA740 Manuel utilisateur

PEERLESS

PEERLESS DS415 Mode d’emploi

PEERLESS

PEERLESS Smartmount D-FPF-220 Mode d’emploi

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur