H3C SecPath NSQM2AC1400 Manuel utilisateur

H3C SecPath NSQM2AC1400

Power Module User Manual

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version: APW101-20170414

and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of New H3C

Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, ,

H3Care, , IRF, NetPilot, Netflow, SecEngine, SecPath,

SecCenter, SecBlade, Comware, ITCMM and HUASAN are

trademarks of New H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to

ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of

any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental

protection requirements. The storage, use, and disposal of this

product must meet the applicable national laws and regulations.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the

H3C website at http://www.h3c.com.hk

To obtain information about installation, configuration, and

maintenance, click http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes,

click http://www.h3c.com.hk/Software_Download

Technical support

[email protected]

http://www.h3c.com.hk

Documentation feedback

You can e-mail your comments about product documentation to

[email protected].

We appreciate your comments.

Contents

Overview ·················································· 1

Front panel ···································································· 2

Technical specifications ··················································· 3

LEDs············································································ 4

Installing and removing the power module······· 6

Installing the power module··············································· 6

Removing the power module············································· 8

Connecting and removing the power cord···························· 8

Overview

The NSQM2AC1400 AC-input DC-output power module has the

following features:

•It has a protection mechanism against input undervoltage,

output overvoltage, output short circuit, output overcurrent, and

overtemperature.

•It is hot swappable. You can install and remove the power

module on an operating device when the power switch on the

power module is turned off.

•It can operate in 1+1 redundancy and supports load balancing.

Front panel

Figure 1 Front panel

(1) Captive screw (2) Power switch

(3) Status LEDs (4) Power cord retainer

(5) AC power receptacle (6) Handle

Technical specifications

Table 1 Technical specifications

Item Specifications

Input voltage range 100 to 240 VAC @ 50/60 Hz

Maximum output current 117 A

Maximum output power •1150 W at 110 VAC

•1400 W at 220 VAC

Dimensions (H × W × D) 128 × 196 × 380 mm (5.04 ×

7.72 × 14.96 in)

Ambient

temperature

Operating

temperature 0°C to 40°C (32°F to 104°F)

Non-operating

temperature –40°C to +70°C (–40°F to

+158°F)

LEDs

CAUTION:

•The power module restores operation automatically when

the power output alarm, such as short circuit, overcurrent, o

overtemperature, is cleared. The power module does not

restore operation automatically when the output overvoltage

alarm is cleared. To restore operation of the power module,

perform the following steps:

a. Turn off the power switch and remove the power cord.

b.Connect the power cord and turn on the power switch.

•Do not frequently turn on or off the power switch. Wait more

than 30 seconds between a turn-on and a turn-off operation.

•After the power switch of the power module is turned off, the

LEDs on the power module will remain on for a while. Make

sure the LEDs are off when you remove the power module.

The power module provides three red/green LEDs: power input LED

(INPUT), power output LED (OUTPUT), and fan status LED (FAN).

Table 2 LED description

LED Status Description

INPUT

Off No power input.

Green Normal power input.

Red Abnormal power input.

LED Status Description

OUTPUT

Off No power output.

Green Normal power output.

Red

The power switch is off.

A power output alarm, such as output

short circuit, overcurrent,

overvoltage, or overtemperature, has

occurred. The power module has

entered self-protection mode.

FAN

Off No power input.

Green The fan is operating correctly.

Red

The power switch is off.

The fan is faulty (The power module

enters self-protection mode and stops

power output two seconds after the

fan fails).

Installing and removing the power

module

CAUTION:

Do not install the NSQM2AC1400 power module and other types

of power modules on the same device.

To avoid bodily injury and device damage, follow the procedures

in Figure 2 and Figure 3, respectively, to install and remove the

power module.

Figure 2 Procedure for installing the power module

Figure 3 Procedure for removing the power module

Installing the power module

1. Wear an ESD wrist strap and make sure the strap makes good

skin contact and is reliably grounded.

2. Unpack the power module. Make sure the power module meets

the power requirements of the device.

3. Holding the power module handle with one hand and supporting

the bottom with the other, push the power module into the slot

along the guide rails. Make sure the power module makes good

contact with the connectors on the backplane.

Install the power

module Connect the power

cord Turn on the power

switch

Table des matières

Autres manuels H3C Unité de contrôle

H3C

H3C PSR6000 Manuel utilisateur

H3C

H3C SecPath M9000-AI NSQM5MBSHA1 Manuel utilisateur

H3C

H3C SIC-4G-CAT6 Manuel utilisateur

H3C

H3C PSR750-A Manuel utilisateur

H3C

H3C LSVM1S9810FAN Manuel utilisateur

H3C

H3C SFP-GE-SX-MM850-A Manuel utilisateur

H3C

H3C SecPath PSR300-12A2 Manuel utilisateur

H3C

H3C PSR450-12A Manuel utilisateur

H3C

H3C PSR2400-12AHAH-B Manuel utilisateur

H3C

H3C SIC-4G-LTE-M Instructions d'utilisation et d'entretien

H3C

H3C LSWM18CQ Manuel utilisateur

H3C

H3C SecPath NSQ1FAB04B0 Manuel utilisateur

H3C

H3C PSR650B-12A2-F Manuel utilisateur

H3C

H3C PSR2400-54D Manuel utilisateur

H3C

H3C SecPath M9000 NSQM1CGQ20 Manuel utilisateur

H3C

H3C S9500 LSB1LB1A0 Manuel utilisateur

H3C

H3C PSR650C-12A Manuel utilisateur

H3C

H3C PSR180-56A Manuel utilisateur

H3C

H3C SR6600 SPE-FWM Manuel utilisateur

H3C

H3C NSQ1FAB04B0 Manuel utilisateur

H3C

H3C PSR150-A1 Manuel utilisateur

H3C

H3C LSQM1CGS2QSA0 Manuel utilisateur

H3C

H3C LSQM1TGT24FD0 Manuel utilisateur

H3C

H3C LSUM1TGT24FD0 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur