H3C NSQM1FWDFGC1 Manuel utilisateur

Manual version: 6PW105-20190315 BOM: 3123A1BU

H3C SecPath M9000 NSQM1FWDFGC1 firewall

module

1 Identifier

The module identifier NSQM1FWDFGC1 is at the upper right corner of the front panel.

2 About the module

The NSQM1FWDFGC1 firewall module is developed for H3C SecPath M9000 security gateways.

The module provides features including firewall, VPN, content filtering, and NAT. By using this

module on an M9000 gateway, you can enhance network security capabilities without changing the

network topology.

3 Specifications

The module has one console port, one USB port, one GE copper port, and a hard disk slot.

Figure 1 Front panel

(1) Hard disk slot (2) Console port (CONSOLE)

(3) GE copper port (10/100/1000BASE-T) (4) USB port (reserved)

(5) Hard disk LED (HD) (6) System status LED (SYS)

(7) Ejector lever (8) Captive screw

Table 1 Module specifications

Item Specification

Flash 8 MB Nor Flash

Memory

Four memory slots

Standard configuration: 32 GB (four 8-GB VLP RDIMMs)

You must install the DDR3 SDRAMs in pairs and each pair must have the

same specifications.

Micro SD card One built-in Micro SD card slot

Standard configuration: 8 GB

Dimensions (H × W × D) 40 ×399 × 352 mm (1.57 × 15.71 × 13.86 in)

Power consumption 180 W to 260 W

Weight 4.8 kg (10.58 lb)

Hot swapping Supported

Manual version: 6PW105-20190315 BOM: 3123A1BU

Item Specification

Ports

•1 console port

•1 USB port (reserved)

•1 GE copper port

•1 hard disk slot

Ambient temperature

•Operating: 5°C to 40°C (41°F to 104°F)

•Storage: –40°C to +70°C (–40°F to +158°F)

Rate of temperature

change

•Operating: < 20°C (68°F)/h

•Storage: < 30°C (86°F)/h

Ambient relative humidity

•Operating: 10% RH to 80% RH, noncondensing

•Storage: 5% RH to 90% RH, noncondensing

Compatible gateway

models and slots

•M9006 gateway (slot 2 to slot 5)

•M9010 gateway (slot 0 to slot 3 and slot 6 to slot 9)

•M9014 gateway (slot 4 and slot 5 and slot 8 to slot 12)

NOTE:

To verify compatibility of the module with the software release you are using, see the release notes.

Table 2 Console port specifications

Item Specification

Connector RJ-45

Interface standard RS-232

Transmission baud rate 9600 bps (default) to 115200 bps

Transmission medium Asynchronous serial cable

Transmission distance ≤15 m (49.21 ft)

Services

•Provides connection to an ASCII terminal.

•Provides connection to the serial port of a local or remote (through a

pair of modems) PC running terminal emulation program.

•Supports command line interface (CLI)

Table 3 10/100/1000BASE-T copper Ethernet port specifications

Item Specification

Connector RJ-45

Interface standard 802.3, 802.3u, and 802.3ab

Interface type MDI/MDIX autosensing

Supported cable Category-5 (or above) twisted pair cable

Transmission distance 100 m (328.08 ft)

Port transmission rate

•10 Mbps, half/full duplex

•100 Mbps, half/full duplex

•1000 Mbps, full duplex

Manual version: 6PW105-20190315 BOM: 3123A1BU

iii

4 LEDs

The module provides LEDs to show the operating status of the module and the hard disk.

Table 4 LED description

LED Status Description

Hard disk (HD)

Flashing green The hard disk is reading and writing data.

Steady green The hard disk is operating correctly.

System status LED

(SYS)

Off No power input or the module is faulty.

Slow flashing green The system has started up and is operating correctly.

Fast flashing green The system is loading the software.

5 Installing and removing the module

CAUTION:

•Wear a reliably-grounded ESD wrist strap or ESD gloves when you install or remove the module.

•Do not touch the components on the module.

The service module slots might be vertical or horizontal, depending on the gateway model. When

installing the module in a horizontal slot, make sure its component side faces up. When installing the

module in a vertical slot, make sure its component side faces left.

The module installation and removable procedures are the same for horizontal or vertical slots. The

following procedures install and remove the module in a horizontal slot.

5.1 Installing the module

1. Face the front panel of the gateway. Remove the filler panel from the target slot.

This example uses slot 3 on the M9006 gateway.

2. Place the module horizontally on a workbench with the component side facing up. Open the

ejector levers on the module.

3. Gently push the module into the slot along the guide rails.

4. Close the ejector levers and make sure the module is in close contact with the backplane.

5. Use a Phillips screwdriver to fasten the captive screws on the module.

Manual version: 6PW105-20190315 BOM: 3123A1BU

Figure 2 Installing the module

5.2 Removing the module

1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is

released.

2. Simultaneously open the ejector levers of the module to separate the module from the

backplane.

3. Simultaneously open the ejector levers on the module to separate the module from the

backplane, and pull the module slowly out of the chassis along the guide rails.

4. Place the module on an anti-static workbench with the component side facing up, or put it in an

anti-static bag.

5. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure

good ventilation in the gateway.

6 Software upgrade

For information about upgrading the module, see the release notes.

The information in this document is subject to change without notice.

Autres manuels H3C Unité de contrôle

H3C

H3C SecPath M9000-AI NSQM5MBSHA1 Manuel utilisateur

H3C

H3C PSR360-56A Manuel utilisateur

H3C

H3C PSR2400-12AHAH-B Manuel utilisateur

H3C

H3C LSQM1SDNB0 Manuel utilisateur

H3C

H3C PSR150-A1 Manuel utilisateur

H3C

H3C SecPath M9000 NSQM1MBFEA0 Manuel utilisateur

H3C

H3C EWPA1PCID Manuel utilisateur

H3C

H3C SecBlade Manuel utilisateur

H3C

H3C LSVM1S9800FAN Manuel utilisateur

H3C

H3C SecPath PSR300-12A2 Manuel utilisateur

H3C

H3C S12500 LST1LB1A1 Manuel utilisateur

H3C

H3C LSBM1WCM2A0 Manuel utilisateur

H3C

H3C Campus SeerEngine LSXM1SEERBXC2 Manuel utilisateur

H3C

H3C S9500 LSB1FW2A0 Manuel de la liste des pièces

H3C

H3C LSUM1TGT24FD0 Manuel utilisateur

H3C

H3C LSQM1CGS2QSA0 Manuel utilisateur

H3C

H3C LSVM2106SFAN Manuel utilisateur

H3C

H3C NSQ1FAB04B0 Manuel utilisateur

H3C

H3C S9500 LSB1LB1A0 Manuel utilisateur

H3C

H3C PSR250-12A Manuel utilisateur

H3C

H3C PSR2400-54A Manuel utilisateur

H3C

H3C SecPath M9000 NSQM1CGQ20 Manuel utilisateur

H3C

H3C NSQ1TGS32SF0 Manuel utilisateur

H3C

H3C R6900-FAN Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur