Graco 25D614 Manuel utilisateur

3A5541D

Instructions

Reactor®2 App Installation Kit

For Reactor 2 Integrated Systems

For remotely changing system settings on Graco Reactor 2 E-30i and E-XP2i systems built.

For professional use only.

Models: 25D614, 25E657

Important Safety Instructions

Read all warnings and instructions in this manual

and in the Reactor®2 manual. Save all instructions.

IMPORTANT

By operating your Reactor 2 system with the cellular

module installed, you are accepting the Graco Reactor

App Terms and Conditions and Software License

Agreement (“Terms”).

To review the Terms, install the Reactor App on your

mobile device or visit www.graco.com.

Models

23A5541D

Contents

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Agency Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . . 6

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mount Cellular Module . . . . . . . . . . . . . . . . . . . . 8

Update ADM Software . . . . . . . . . . . . . . . . . . . . 9

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connect App to Reactor . . . . . . . . . . . . . . . . . . 10

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Reactor 2 App . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Cellular Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

View Cellular Screen . . . . . . . . . . . . . . . . . . . . . 12

Reset Reactor Key . . . . . . . . . . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Disconnect Cellular Module . . . . . . . . . . . . . . . . 13

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Cellular Module and Antenna . . . . . . . . . . . . . . 14

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Technical Specifications . . . . . . . . . . . . . . . . . . . . 15

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 16

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 16

Models

Related Manuals

Kit Included Cellular Module Description

25D614 25M720 3G cellular module, operational worldwide

25E657 25E372 LTE CAT-1 (4G) cellular module, only operational in

the United States and Canada

Manual in

English Description

3A1705 Reactor 2 E-30i and E-XP2i Proportioning Systems

(Operation)

3A1706 Reactor 2 E-30i and E-XP2i Proportioning Systems

(Repair-Parts)

332636 Reactor 2 Elite Integrated Proportioning Systems

(Operation)

332637 Reactor 2 Elite Integrated Proportioning Systems

(Repair-Parts)

Agency Approvals

3A5541D 3

Agency Approvals

NOTE: Cellular module kit 25M833 contains Part 25M720. Cellular module kit 25E658 contains Part 25N372.

Description Approvals

MODULE, cellular, worldwide (25M720)

MODULE, cellular, United States and Canada only

(25N372)

Warnings

43A5541D

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks.

When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.

Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this

manual where applicable.

WARNING

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause

electric shock.

• Turn off and disconnect power at main switch before disconnecting any cables and before servicing

or installing equipment.

• Connect only to grounded power source.

• All electrical wiring must be done by a qualified electrician and comply with all local codes and

regulations.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Specifications in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical

Specifications in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For

complete information about your material, request Safety Data Sheets (SDSs) from distributor or

retailer.

• Do not leave the work area while equipment is energized or under pressure.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and

create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing

equipment, follow the Pressure Relief Procedure and disconnect all power sources.

Warnings

3A5541D 5

Typical Installation

63A5541D

Typical Installation

FIG. 1: Typical Cell Module Installation (Integrated Reactor)

WLD

$'0

(

)

Typical Installation

3A5541D 7

FIG. 2: Typical Cell Module Installation (Integrated Reactor 2)

WLD

$'0

(

)

Ref. Description

A Cellular Module

AA Mounting Screws

ADM* Advanced Display Module

B Antenna

C Cellular Module CAN Cable

D* Power Supply Cable

E Air Panel Cover (Compatible with Cellular

Module)

F Warning Label

* Included with Reactor 2 proportioner.

Ref. Description

Overview

83A5541D

Overview

The Reactor 2 App allows the Graco Reactor 2 to be

monitored and operated remotely. The Reactor 2 is

intended to be controlled by an on-site operator. In any

lock-out, tag-out procedure, take into consideration the

potential for changes to the Reactor 2 settings due to

remote operation.

Installation

Mount Cellular Module

1. Shut down system. See your Reactor 2 operation

manual for shutdown instructions.

2. Disconnect incoming power at source.

3. Remove the original air panel cover. Install the

cellular module-compatible air panel cover (E).

NOTE: For units with Graco InSite, remove both the

mounting screws and the InSite module from the

existing air panel cover. Set aside.

4. Install the warning label (F) on the back of the new

air panel cover (E) as shown in FIG. 1 and FIG. 2.

5. Install the cellular module (A) onto the back of the

new air panel cover using the predrilled holes and

two mounting screws (AA).

NOTE: For units with Graco InSite, reinstall the InSite

module onto the back of the new air panel cover using

the remaining predrilled holes and InSite mounting

screws.

6. Disconnect the power supply cable (D) from the

ADM. Connect the loose end of the power supply

cable to the cellular module (A).

7. Connect the cellular module CAN cable (C) to the

cellular module and the ADM. Tighten by hand.

8. Attach the antenna (B) to the cellular module.

Tighten by hand.

9. During first use, complete Update ADM Software,

page 9.

To avoid injury due to unexpected machine operation

initiated by remote controller, disconnect the cellular

module from the system prior to troubleshooting. See

Disconnect Cellular Module, page 13.

Installation

3A5541D 9

Update ADM Software

1. Shut down system. See your Reactor operation

manual for shutdown instructions.

2. Loosen the set screw on the ADM mounting bracket.

Remove the ADM from the bracket.

3. Remove the token access panel on the back of the

ADM.

4. Insert and press the software upgrade token firmly

into the slot.

NOTE: There is no preferred orientation of the token.

5. Turn on the system power.

NOTE: When the ADM display turns on, you may see

the following screens:

6. Remove the software update token.

7. Replace the token access panel.

8. Remount the ADM. Tighten the set screw fully.

9. Press to continue to the operation screen.

NOTICE

A status is shown while software is updating to

indicate progress. To prevent corrupting the software

load, do not remove the token until the status screen

disappears.

First:

Software is checking which

modules will take the

available updates.

Second:

Status of the update with

approximate time until

completion.

Third:

Updates are complete.

Icon indicates update

success/failure. See the

following table.

Icon Description

Update successful.

Update unsuccessful.

Update complete, no changes necessary.

Modules were updated or didn’t require

an update; however, one or more mod-

ules need to be updated manually with a

token.

Setup

10 3A5541D

Setup

Download the Graco Reactor app on the Apple App

Store®or the Android Google Play™store.

1. Open the Reactor App on your smartphone.

2. Read and accept the Terms of Use and data usage

notification.

3. Review the app tutorial.

Connect App to Reactor

1. On the Reactor ADM, press to enter the

setup mode.

2. Press to go to the Cellular screen (see FIG.

4).

NOTE: Before connecting the Reactor to an app for the

first time, Reset Reactor Key. See page 12.

3. To connect the app to the Reactor, scan the code.

a. Select the Scan code button on the app. (See

FIG. 3.)

b. Using the app and your smartphone camera,

scan the code displayed on the ADM Cellular

screen.

4. If you have trouble scanning the code, type in the

IMEI and the key instead.

a. Select Type in IMEI and key. (See FIG. 3.)

b. Enter the Reactor IMEI found on the ADM

Cellular screen.

c. Enter the Reactor key found on the ADM

Cellular screen.

d. Select the Connect button on the app.

FIG. 3: Connect Screen in App

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Graco Unité de contrôle

Graco

Graco 25C453 Manuel utilisateur

Graco

Graco Dyna-Star 24Y408 Manuel d'utilisation et d'entretien

Graco

Graco PD44 Guide de dépannage

Graco

Graco 246085 Mode d’emploi

Graco

Graco NXT011 Manuel d'utilisation

Graco

Graco CleanShot Manuel utilisateur

Graco

Graco 257836 Manuel utilisateur

Graco

Graco Therm-O-Flow 194485 Manuel d'utilisation

Graco

Graco 207861 Manuel utilisateur

Graco

Graco CGM 25B127 Manuel de la liste des pièces

Graco

Graco PD44 Manuel utilisateur

Graco

Graco E-Flo B Series Manuel de la liste des pièces

Graco

Graco 255751 Manuel utilisateur

Graco

Graco 234026 Manuel utilisateur

Graco

Graco Airgard 224-040 Manuel d'utilisation

Graco

Graco 244920 Manuel d'utilisation

Graco

Graco PrecisionFlo 233678 Manuel d'utilisation

Graco

Graco ProMix Auto Manuel utilisateur

Graco

Graco 24J415 Manuel de la liste des pièces

Graco

Graco Cleanshot 244162 Manuel utilisateur

Graco

Graco Dyna-Star 77X540 Manuel utilisateur

Graco

Graco 222-411 Fiche technique

Graco

Graco Reactor 25D612 Manuel utilisateur

Graco

Graco 15X303 Manuel de référence technique

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

Flyron

Flyron FN-BC04 Manuel utilisateur