Endress+Hauser ITEMP TMT82 Manuel utilisateur

Products Solutions Services

Operating Instructions

iTEMP TMT82

Dual-input temperature transmitter

BA01028T/09/EN/17.17

71355027

Valid as of version

01.01 (device version)

iTEMP TMT82 Table of contents

Endress+Hauser 3

Table of contents

1 Important document information .... 4

1.1 Function of document and how to use ........ 4

1.2 Symbols .............................. 4

1.3 Tool symbols .......................... 6

1.4 Further standard device documentation ...... 6

1.5 Registered trademarks ................... 6

2 Basic safety instructions ............ 7

2.1 Requirements for the personnel ............ 7

2.2 Designated use ........................ 7

2.3 Operational safety ...................... 7

3 Identification ....................... 8

3.1 Device designation ...................... 8

3.2 Scope of delivery ....................... 9

3.3 Certificates and approvals ................ 9

4 Installation ....................... 11

4.1 Incoming acceptance, transport, storage ..... 11

4.2 Installation conditions .................. 11

4.3 Installation .......................... 11

4.4 Post-installation check .................. 16

5 Wiring ............................ 17

5.1 Quick wiring guide ..................... 17

5.2 Connecting the sensor cables ............. 18

5.3 Connecting the power supply and signal

cables .............................. 19

5.4 Shielding and grounding ................ 20

5.5 Post-connection check .................. 21

6 Operating options ................. 22

6.1 Overview of operation options ............ 22

6.2 Structure and function of the operating

menu .............................. 23

6.3 Measured value display and operating

elements ............................ 25

6.4 Access to the operating menu via the

operating tool ........................ 27

7 Integrating the transmitter via the

HART® protocol ................... 30

7.1 HART device variables and measured values .. 30

7.2 Device variables and measured values ....... 31

7.3 Supported HART® commands ............. 31

8 Commissioning .................... 33

8.1 Post-installation check .................. 33

8.2 Switching on the transmitter ............. 33

8.3 Enabling configuration .................. 33

9 Maintenance ...................... 33

10 Accessories ....................... 34

10.1 Device-specific accessories ............... 34

10.2 Communication-specific accessories ........ 34

10.3 Service-specific accessories ............... 35

10.4 System components .................... 35

11 Diagnostics and troubleshooting ... 37

11.1 Troubleshooting ...................... 37

11.2 Diagnostics events ..................... 39

11.3 Spare parts .......................... 42

11.4 Return .............................. 43

11.5 Disposal ............................ 43

11.6 Software history and overview of

compatibility ......................... 43

12 Technical data .................... 44

13 Operating menu and parameter

description ........................ 60

13.1 "Setup" menu ......................... 66

13.2 "Diagnostics" menu ..................... 86

13.3 "Expert" menu ........................ 94

Index ................................. 112

Important document information iTEMP TMT82

4 Endress+Hauser

1 Important document information

1.1 Function of document and how to use

1.1.1 Document function

These Operating Instructions contain all the information that is required in various phases

of the life cycle of the device: from product identification, incoming acceptance and

storage, to mounting, connection, operation and commissioning through to

troubleshooting, maintenance and disposal.

1.1.2 Safety Instructions (XA)

When using in hazardous areas, compliance with national regulations is mandatory.

Separate Ex-specific documentation is provided for measuring systems that are used in

hazardous areas. This documentation is an integral part of these Operating Instructions.

The installation specifications, connection data and safety instructions it contains must be

strictly observed! Make sure that you use the right Ex-specific documentation for the right

device with approval for use in hazardous areas! The number of the specific Ex

documentation (XA...) is provided on the nameplate. If the two numbers (on the Ex

documentation and the nameplate) are identical, then you may use this Ex-specific

documentation.

1.1.3 Functional safety

Please refer to Safety Manual SD01172T/09 for the use of approved devices in

protective systems according to IEC 61508.

1.2 Symbols

1.2.1 Safety symbols

Symbol Meaning

DANGER

A0011189-EN

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will

result in serious or fatal injury.

CAUTION

A0011191-EN

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can

result in minor or medium injury.

NOTICE

A0011192-EN

NOTE!

This symbol contains information on procedures and other facts which do not

result in personal injury.

1.2.2 Electrical symbols

Symbol Meaning

A0011197

Direct current

A terminal to which DC voltage is applied or through which direct current flows.

A0011198

Alternating current

A terminal to which alternating voltage (sine-wave) is applied or through which alternating

current flows.

iTEMP TMT82 Important document information

Endress+Hauser 5

Symbol Meaning

A0011200

Ground connection

A grounded terminal which, as far as the operator is concerned, is grounded via a grounding

system.

A0011199

Protective ground connection

A terminal which must be connected to ground prior to establishing any other connections.

A0011201

Equipotential connection

A connection that has to be connected to the plant grounding system: This may be a potential

equalization line or a star grounding system depending on national or company codes of practice.

1.2.3 Symbols and notation for certain types of information

Symbol Meaning

A0011182

Allowed

Indicates procedures, processes or actions that are allowed.

A0011183

Preferred

Indicates procedures, processes or actions that are preferred.

A0011184

Forbidden

Indicates procedures, processes or actions that are forbidden.

A0011193

Tip

Indicates additional information.

A0011194

Reference to documentation

Refers to the corresponding device documentation.

A0011195

Reference to page

Refers to the corresponding page number.

A0011196

Reference to graphic

Refers to the corresponding graphic number and page number.

1., 2., 3. Series of steps

Result of a sequence of actions

1.2.4 Symbols and notation in graphics

Symbol Meaning

1,2,3 ... Item numbers

A, B, C, ... Views

A-A, B-B, C-C, ... Sections

A0011187

Hazardous area

Indicates a hazardous area.

A0011188

Safe area (non-hazardous area)

Indicates the non-hazardous area.

Important document information iTEMP TMT82

6 Endress+Hauser

1.3 Tool symbols

Symbol Meaning

A0011220

Flat blade screwdriver

A0011219

Crosstip screwdriver

A0011221

Allen key

A0011222

Open-ended wrench

A0013442

Torx screwdriver

1.4 Further standard device documentation

Document Purpose and content of the document

Technical Information

TI01010T/09/en

Planning aid for your device

The document contains all the technical data on the device and provides

an overview of the accessories and other products that can be ordered for

the device.

Brief Operating Instructions

KA01095T/09/en

Guide that takes you quickly to the 1st measured value

The Brief Operating Instructions contain all the essential information

from incoming acceptance to initial commissioning.

The document types listed are available:

In the Download Area of the Endress+Hauser Internet site: www.endress.com →

Download

1.5 Registered trademarks

HART®

Registered trademark of the HART® FieldComm Group

iTEMP TMT82 Basic safety instructions

Endress+Hauser 7

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill

the following requirements:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Before beginning work, the specialist staff must have read and understood the

instructions in the Operating Instructions and supplementary documentation as well as

in the certificates (depending on the application)

‣Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

‣Being instructed and authorized according to the requirements of the task by the

facility's owner-operator

‣Following the instructions in these Operating Instructions

2.2 Designated use

The device is a universal and user-configurable temperature transmitter with either one or

two sensor inputs for a resistance thermometer (RTD), thermocouples (TC), resistance and

voltage transmitters. The head transmitter version of the device is intended for mounting

in a flat-face terminal head as per DIN EN 50446. It is also possible to mount the device on

a DIN rail using the optional DIN rail clip. The device is also optionally available in a

version suitable for DIN rail mounting as per IEC 60715 (TH35).

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Operational safety

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the

hazardous area (e.g. explosion protection or safety equipment):

‣Based on the technical data on the nameplate, check whether the ordered device is

permitted for the intended use in the hazardous area. The nameplate can be found on

the side of the transmitter housing.

‣Observe the specifications in the separate supplementary documentation that is an

integral part of these Instructions.

Electromagnetic compatibility

The measuring system complies with the general safety requirements as per EN 61010-1,

the EMC requirements as per the IEC/EN 61326 series and the NAMUR recommendations

NE 21 and NE 89.

NOTICE

‣The unit must only be powered by a power supply that operates using an energy-

limited electric circuit that is compliant with IEC 61010-1, "SELV or Class 2 circuit".

Identification iTEMP TMT82

8 Endress+Hauser

3 Identification

3.1 Device designation

The following options are available for identification of the device:

• Nameplate specifications

• Enter the serial number from the nameplate in the W@M Device Viewer

(www.endress.com/deviceviewer): All data relating to the device and an overview of

the Technical Documentation supplied with the device are displayed.

3.1.1 Nameplate

The right device?

Compare and check the data on the nameplate of the device against the requirements of

the measuring point:

12 3

11-42V 012345678910

xx.yy.zz

TMT82- XXXXX/XX

iTEMP

Made in Germany 2016

D-87484 Nesselwang

Ser.no.:

FW:

Input:

12345678ABCDEFGH

Current consum.: 23,6 mA Dev.Rev: x

Ext. ord. cd.:

XXXXXXXXXXXXX#

EH 08.001X

II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C

II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C

Install per XA00102R/09/a3/xx.xx

0044

A0014561

 1 Nameplate of the head transmitter (example, Ex version)

1 Power supply, current consumption and extended order code

2 Serial number, device revision and firmware version

3 Data Matrix 2D code

4 2 lines for the TAG name

5 Approval in hazardous area with number of the relevant Ex documentation (XA...)

6 Approvals with symbols

7 Order code and manufacturer ID

iTEMP TMT82 Identification

Endress+Hauser 9

0044

iTEMP®TMT82

Made in Germany 2012 D-87484 Nesselwang

TAGXXXXXXXXXXX

FW: XX.XX.XX Dev. Rev.: X

Order code: TMT82-xxx/xx

Ext. ord. cd.: XXXXXXXXXXX

Ser. no.: XXXXXXXXX

Input: 12-42 V

Current cunsum.: 23,0 mA

II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C

II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C

EH 08.001X

Install per XA0xxxxT/09/a3/xx.xx

A0017924

 2 Nameplate of DIN rail transmitter (example, Ex version)

1 Product description and manufacturer ID

2 Order code, extended order code and serial number

3 Power supply and current consumption

4 Approval in hazardous area with number of the relevant Ex documentation (XA...)

5 Firmware version and device version

6 Approval logos

7 2 lines for the TAG name

3.2 Scope of delivery

The scope of delivery of the device comprises:

• Temperature transmitter

• Mounting material (head transmitter)

• Hard copy of multi-language Brief Operating Instructions

• Functional Safety Manual (SIL mode)

• Additional documentation for devices which are suitable for use in the hazardous area

(0 1), such as Safety Instructions (XA), Control or Installation Drawings (ZD).

3.3 Certificates and approvals

The device left the factory in a safe operating condition. The device complies with the

requirements of the standards EN 61 010-1 "Safety Requirements for Electrical Equipment

for Measurement, Control, and Laboratory Use" and with the EMC requirements as per the

IEC/EN 61326 series.

3.3.1 CE/EAC mark, declaration of conformity

The device meets the legal requirements of the EU/EEU guidelines. The manufacturer

confirms that the device is compliant with the relevant guidelines by applying the CE/EAC

mark.

3.3.2 HART® protocol certification

The temperature transmitter is registered by the HART® FieldComm Group. The device

meets the requirements of the HART Communication Protocol Specifications, Revision 7

(HCF 7.4).

Identification iTEMP TMT82

10 Endress+Hauser

3.3.3 Functional safety

The two device versions (head transmitter/DIN rail device) are optionally available for use

in safety systems as per IEC 61508.

• SIL 2: Hardware version

• SIL 3: Software version

Autres manuels pour iTEMP TMT82

Table des matières

Autres manuels Endress+Hauser Émetteur

Endress+Hauser

Endress+Hauser Levelflex FMP 232 Fiche technique

Endress+Hauser

Endress+Hauser cerabar S PROFIBUS-PA Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CXM 223 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT71 Manuel utilisateur

Endress+Hauser

Endress+Hauser Mycom CLM 152 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT71 Instructions d'installation

Endress+Hauser

Endress+Hauser Liquisys M CLM223F Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquiline CM442R Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CUM223 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT162 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT71 Manuel utilisateur

Endress+Hauser

Endress+Hauser FHX50 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CLM223F Manuel utilisateur

Endress+Hauser

Endress+Hauser Nivotester FTR525 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT85 Manuel utilisateur

Endress+Hauser

Endress+Hauser PROline promag 53 Instructions d'installation

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Manuel utilisateur

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT84 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT111 Manuel utilisateur

Endress+Hauser

Endress+Hauser CM14-AAK Manuel utilisateur

Endress+Hauser

Endress+Hauser AT5000 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CCM223 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Endress+Hauser iTEMP TMT82 Manuel utilisateur

Manuels Émetteur populaires d'autres marques