Endress+Hauser Mycom S CLM 153 Manuel utilisateur

BA234C/07/en/12.02

51503794

Software version 1.20 or later

Mycom S

CLM 153

Conductivity Transmitter

Operating Instructions

MYCOM S CLM 153

ENDRESS+HAUSER

MEAS CAL

DIAG PARAM

Wahl

3.52

µS/cm

PS1

Select

Measure

First commissioning page 23 Mycom S CLM 153

2Endress+Hauser

First commissioning .................................... page 23

Using the menu "Quick Setup" in the chapter "First commissioning" you can configure

the transmitter with the most important parameters quickly and easily. Important basic

functions such as language, measured variable, temperature compensation and

current outputs are configured directly with the help of the on-site display.

You carry out further configuration in the corresponding menus as required.

Brief operating instructions

"PARAM": Parameter entry menu

"PARAM" allows you to return to the previous "return field" from any point in the menu.

"DIAG": brings you to the instrument diagnosis menu.

Help page: Press "DIAG" and "PARAM" together

"MEAS": Measuring mode

Press "MEAS" to exit any of the menus ("PARAM", "DIAG", "CAL") without having

completed the settings / calibration.

"CAL": Calibration

"E": (Enter): Continue in menu / confirm your selection

LED: "green" = everything OK. "red" = error.

Arrow keys:

• Scroll through items and highlight a selection or

• increment/decrement numbers by one step with "+" / "-".

Next digit: using the "right arrow" (editor type 1) or

• "Activate" with the "right arrow" and scroll through the selection with "+" / "-"

(editor type 2).

Mycom S CLM 153

Endress+Hauser 3

Table of Contents

1 Safety instructions . . . . . . . . . . . . . . . . . 4

1.1 Notes on safety conventions and icons . . . . . 4

1.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Installation, Commissioning, Operation . . . . . . 5

1.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . 5

1.5 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Identification . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Device designation . . . . . . . . . . . . . . . . . . . . . 7

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Certificates and approvals . . . . . . . . . . . . . . . 8

3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Incoming acceptance, transport, storage . . . 9

3.2 Installation conditions . . . . . . . . . . . . . . . . . . . 9

3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4 Post-installation check . . . . . . . . . . . . . . . . . . 11

4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . 12

4.2 Connecting the measuring system . . . . . . . . 14

4.3 Post-connection check . . . . . . . . . . . . . . . . . 17

5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.1 Display and operating elements . . . . . . . . . . 18

5.2 Replaceable memory . . . . . . . . . . . . . . . . . . 22

6 Commissioning . . . . . . . . . . . . . . . . . . . 23

6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . 23

6.2 Switching on the measuring device . . . . . . . 23

6.3 Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.4 Description of functions . . . . . . . . . . . . . . . . . 30

7 Maintenance . . . . . . . . . . . . . . . . . . . . . . 83

7.1 Maintaining the measuring system . . . . . . . . . 83

8 Troubleshooting . . . . . . . . . . . . . . . . . 87

8.1 Troubleshooting instructions . . . . . . . . . . . . . 87

8.2 Response of outputs to errors . . . . . . . . . . . . 94

8.3 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . 94

8.4 Installation and removal of parts . . . . . . . . . . 96

8.5 Replacing the device fuses . . . . . . . . . . . . . . 97

8.6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

9 Accessories . . . . . . . . . . . . . . . . . . . . . . . 98

10 Technical data . . . . . . . . . . . . . . . . . . . 101

10.1 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

10.2 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

10.3 Performance characteristics . . . . . . . . . . . . . 103

10.4 Environment . . . . . . . . . . . . . . . . . . . . . . . . . 104

10.5 Mechanical construction . . . . . . . . . . . . . . . 104

11 Appendix . . . . . . . . . . . . . . . . . . . . . . . . 105

11.1 Operating matrix . . . . . . . . . . . . . . . . . . . . . 105

1 Safety instructions Mycom S CLM 153

4Endress+Hauser

1 Safety instructions

1.1 Notes on safety conventions and icons

General safety instructions

Electrical symbols

Warning!

This symbol alerts you to hazards which could cause serious injuries as well as damage to the instrument if

ignored.

Caution!

This symbol alerts you to possible faults which could arise from incorrect operation. They could cause

damage to the instrument if ignored.

Note!

This symbol indicates important items of information.

DC voltage

A terminal at which DC voltage is applied or through which DC flows.

AC voltage

A terminal at which (sine-form) AC voltage is applied or through which AC flows.

)

Ground connection

A grounded terminal, which, from the user’s point of view, is already grounded using a ground system.

Protective earth terminal

A terminal which must be grounded before other connections may be set up.

Equipotential connection

A connection which must be connected to the grounding system of the equipment. This can be, for example,

a potential matching line of a star-shaped grounding system, depending on national or company practice.

Double insulation

The equipment is protected with double insulation.

Alarm relay

Input

Output

Mycom S CLM 153 1 Safety instructions

Endress+Hauser 5

1.2 Designated use

The transmitter Mycom S CLM 153 is a device for measuring conductivity. The

transmitter is designed for measuring or control tasks in applications in the following

industries:

•Chemical process systems

•Pharmaceuticals

•Foodstuff industry

•Water treatment and monitoring

The Ex-version of the Mycom S CLM 153 makes operation in hazardous atmospheres

also possible (see "Certificates" in the product structure on page 7).

Any other use than the one described here compromises the safety of persons and the

entire measuring system and is, therefore, not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

1.3 Installation, Commissioning, Operation

Please note the following items:

•Installation, electrical connection, commissioning, operation and maintenance of the

measuring system must only be carried out by trained technical personnel.

The technical personnel must be authorised for the specified activities by the system

operator.

•Technical personnel must have read and understood theses Operating Instructions

and must adhere to them.

•Before commissioning the entire measuring point, check all the connections for

correctness. Ensure that electrical cables and hose connections are not damaged.

•Do not operate damaged products and secure them against unintentional

commissioning.

•Measuring point faults may only be rectified by authorised and specially trained

personnel.

•If faults can not be rectified, the products must be moved from service and secured

against unintentional commissioning.

•Repairs not described in these Operating Instructions may only be carried out at the

manufacturer’s or by the Endress+Hauser service organisation.

1.4 Operational safety

Warning!

If the device is used for any application other than those described in these Operating

Instructions, it may lead to unsafe and improper functioning of the measuring system

and is therefore not permitted.

The instrument has been designed and tested according to the state of the art and left

the factory in perfect functioning order. The instrument meets all the prevailing

regulations and EC directives - see "Technical data".

However, always pay attention to the following points:

•Measuring systems used in Ex areas have a separate document (XA 233C/07/a3)

which forms a component part of these Operating Instructions. Always follow the

installation regulations and the - partly deviating - connection data of the Ex documen-

tation as well. You can find the following symbols on the front page of the additional

1 Safety instructions Mycom S CLM 153

6Endress+Hauser

Ex documentation (according to approval and test centre

(

Europe,

USA,

Canada).

•The measuring device complies with the general safety requirements in accordance

with EN 61010, the EMC requirements of EN 61326, and NAMUR Recommendation

NE 21, 1998.

•The manufacturer reserves the right to change the technical data in line with technical

progress at any time. You can obtain information on the current version of these

Operating Instructions and possible additions from your E+H sales centre.

1.4.1 Immunity to interference

This instrument has been tested for electromagnetic compatibility in industrial use

according to applicable European standards. It is protected against electromagnetic

interference by the following design measures:

•cable screening

•interference suppression filter

•interference suppression capacitors

Warning!

Protection against interference as specified above is valid only for an instrument

connected according to the instructions in these Operating Instructions.

1.5 Return

If the transmitter has to be repaired, please return it cleaned to the E+H sales centre

responsible. You can find the address on the last page of these instructions. For returns

please use the original packaging.

With the instrument, please enclose a completed copy of the "Declaration of

Contamination" form. You can find this at the end of these Operating Instructions.

Mycom S CLM 153 2 Identification

Endress+Hauser 7

2 Identification

2.1 Device designation

2.1.1 Product structure

Conductivity transmitter in aluminium housing for wall mounting with one alarm and two

output contacts for NAMUR, ChemoClean and controller functions as well as three

binary inputs, logbooks, data loggers, USP limit functions. Plain text operation.

247x167x111 mm (HxWxD). Degree of protection IP 65.

Certificates

A Basic equipment: non-Ex

G With Atex approval, Atex II (1) 2G EEx em ib[ia] IIC T4

O With FM approval; NI Cl. I, Div. 2, Sensor IS Cl. I, Div. 1

P With FM approval; NI Cl. I, Div. 2

S With CSA approval; NI Cl. I, Div. 2, Sensor IS Cl. I, Div. 1

T With TIIS approval

Measuring input

1 1 measuring circuit for conductive sensors, conductivity/resistance and temperature

2 1 measuring circuit for inductive sensors, conductivity/resistance and temperature

3 2 measuring circuits for conductive sensors, conductivity/resistance and temperature

4 2 measuring circuits for inductive sensors, conductivity/resistance and temperature

Measuring output

A 2 current outputs 0/4 ... 20 mA, passive (Ex and non-Ex)

B 2 current outputs 0/4 ... 20 mA, active (non-Ex)

C HART with 2 current outputs 0/4 ... 20 mA, passive (Ex and non-Ex)

D HART with 2 current outputs 0/4 ... 20 mA, active (non-Ex)

E PROFIBUS-PA, without current outputs

Contacts, current input

0 Without additional contacts

1 3 additional contacts

2 2 additional contacts, 1 passive current input (Ex and non-Ex)

3 2 additional contacts, 1 resistance input (non-Ex)

4 1 additional contact, 2 passive current inputs (Ex and non-Ex)

5 1 additional contact, 1 passive current input, 1 active resistance input (non-Ex)

Power supply

0 100 ... 230 V AC

8 24 V AC / DC

Language versions

A E / D

B E / F

C E / I

D E / ES

E E / NL

F E / J

Cable connection

0 Cable glands M 20 x 1.5

1 Adapter for cable gland NPT ½"

2 Adapter for cable gland G ½

Additional equipment

0 Without additional equipment

1 Additional equipment: DAT module

Configuration

0 Factory settings

CLM 153- Complete order code

2 Identification Mycom S CLM 153

8Endress+Hauser

2.1.2 Nameplate

2.2 Scope of delivery

The scope of delivery comprises:

•Instrument type and version acc. to the nameplate (s. chap. 2.1.2)

•Operating Instructions BA 234C/07/en (for Ex-system also the XA 233C/07/a3)

2.3 Certificates and approvals

Declaration of conformity

The product meets the legal requirements of the harmonised European standards.

Endress+Hauser confirms compliance with the standards by affixing the

symbol.

Fig. 1: Example of a nameplate for the transmitter Mycom S CLM 153.

Mycom S CLM 153 3 Installation

Endress+Hauser 9

3Installation

3.1 Incoming acceptance, transport, storage

•Make sure the packaging is undamaged!

Inform the deliverer about damage to the packaging.

Keep the damaged packaging until the matter has been clarified.

•Make sure the contents are undamaged!

Inform the deliverer about damage to the delivery contents.

Keep the damaged products until the matter has been clarified.

•Use the delivery papers and your order to check that the scope of delivery is

complete.

•For storage and transport purposes, pack the instrument so that it is protected against

impacts and humidity. The original packaging offers the best protection. Also, keep to

the approved ambient conditions (see "Technical data").

•If you have any questions, please contact your supplier or your nearest

Endress+Hauser sales centre, (see the back page of these Operating Instructions).

3.2 Installation conditions

3.2.1 Dimensions

You can find the dimensions and lengths of the transmitter in the Technical data on

page 101 ff.

3.3 Installation

3.3.1 Installation instructions

•The standard use of the Mycom S CLM 153 transmitter is as a field instrument.

•The Mycom S CLM 153 transmitter can be fixed to vertical or horizontal pipes using

the round post fixture available from Endress+Hauser (see Accessories). When

installing the instrument outdoors, you also require the weather protection cover

CYY 101. This cover is compatible with all field instrument installations options.

•Always install the transmitter so that the cable entries point downwards.

•The transmitter can be installed as a panel-mounted unit as well.

3.3.2 Wall mounting

Caution!

•Check that the temperature does not exceed the maximum permitted ambient

temperature (–20°... +60°C). Install the instrument in a shady location. Avoid direct

sunlight.

•Mount the wall mounting housing so that the cable entries always point downwards.

3 Installation Mycom S CLM 153

10 Endress+Hauser

Fig. 2: Dimensions for wall mounting: Fixing screw: dia. 6 mm

Wall plug: dia. 8 mm

1: Fixing drillholes

2: Plastic cover caps

For the wall mounting of the transmitter proceed as follows:

1. Prepare drill holes acc. to fig. 2

2. Push the two fixing screws from the front through the appropriate fixing bores ➀.

–Fixing screws (M6): max. dia. 6.5 mm

–Screw head: max. dia. 10.5 mm

3. Mount the transmitter housing on the wall as shown.

4. Cover the drill holes with the plastic cover caps ➁.

3.3.3 Post mounting and panel mounting

Mount the parts of the mounting kit (see

accompanying figure) at the back of the

housing as depicted in fig. 4.

Required mounting cutout for panel

mounting: 161 x 241 mm

Installation depth: 134 mm

Pipe diameter: max. 70 mm.

Fig. 3: Mounting kit Mycom S CLM 153

154

100

247

142

167

∅8

C07-CPM153xx-11-00-08-xx-001.EPS

Table des matières

Autres manuels Endress+Hauser Émetteur

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CPM223 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT80 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT82 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT162 Manuel utilisateur

Endress+Hauser

Endress+Hauser Cerabar S PMP71 Manuel utilisateur

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT71 Manuel utilisateur

Endress+Hauser

Endress+Hauser HART Proline 400 Caractéristiques techniques

Endress+Hauser

Endress+Hauser iTEMP TMT85 Manuel utilisateur

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Manuel

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manuel utilisateur

Endress+Hauser

Endress+Hauser Flowmeter Proline 300 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Liquisys M CCM223 Manuel utilisateur

Endress+Hauser

Endress+Hauser RMA42 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Flowmeter Proline 300 Caractéristiques techniques

Endress+Hauser

Endress+Hauser iTEMP TMT84 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Liquiline CM42 Caractéristiques techniques

Endress+Hauser

Endress+Hauser CUM 740 Manuel utilisateur

Endress+Hauser

Endress+Hauser HART iTEMP TMT182B Manuel utilisateur

Endress+Hauser

Endress+Hauser AT1000 AT1 Manuel utilisateur

Endress+Hauser

Endress+Hauser FHX50 Manuel utilisateur

Endress+Hauser

Endress+Hauser Mycom CLM 152 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur