Endress+Hauser ITEMP TMT82 Caractéristiques techniques

Brief Operating Instructions

iTEMP® TMT82

Dual-Input Temperature Head Transmitter

These instructions are Brief Operating Instructions.

For detailed information, refer to the Operating Instructions and other

documentation on the CD-ROM provided or visit "www.endress.com/

deviceviewer".

These Brief Operating Instructions do not act as a substitute for the Operating

Instructions included in the scope of delivery.

The complete device documentation comprises:

• These Brief Operating Instructions

•A CD-ROM with PDF files of:

– Operating Instructions

– Approval and safety certificates

– Further device specific information.

KA01095T/09/EN/13.10

71124515

Table of contents iTEMP® TMT82

2 Endress+Hauser

Table of contents

1 Important document information ............................... 2

1.1 About this document ............................................ 2

1.2 Document conventions ........................................... 3

2 Basic safety instructions ...................................... 4

2.1 Requirements for the personnel ....................................... 4

2.2 Designated use ............................................... 4

2.3 Operational safety .............................................. 4

3 Identification ............................................. 5

3.1 Device designation ............................................. 5

3.2 Scope of delivery .............................................. 6

3.3 Certificates and approvals .......................................... 6

4 Installation instructions ...................................... 6

4.1 Incoming acceptance, transport, storage ................................... 6

4.2 Installation conditions ............................................ 7

4.3 Installation instructions ........................................... 7

4.4 Post-installation check ........................................... 10

5 Wiring ................................................. 10

5.1 Quick wiring guide ............................................. 11

5.2 Connecting the sensor cables ........................................ 12

5.3 Connecting the power supply and signal cables ............................... 13

5.4 Shielding and grounding .......................................... 14

5.5 Post-connection check ........................................... 15

6 Operating options ......................................... 16

6.1 Measured value display and operating elements ............................... 16

6.2 Configuration of the head transmitter via HART® protocol .......................... 18

7 Commissioning ........................................... 19

7.1 Function check .............................................. 19

7.2 Switching on the head transmitter ..................................... 19

7.3 Enabling configuration ........................................... 19

1 Important document information

1.1 About this document

1.1.1 Document function

These Brief Operating Instructions contain all the information that is required in various phases

of the life cycle of the device: from product identification, incoming acceptance and storage, to

mounting, connection and operation.

1.1.2 Safety Instructions (XA)

When using in hazardous areas, the national safety requirements must be met. Separate Ex

documentation is contained in these Operating Instructions for measurement systems that are

iTEMP® TMT82 Important document information

Endress+Hauser 3

to mounted in hazardous areas. Strict compliance with the installation instructions, ratings and

safety instructions as listed in this supplementary documentation is mandatory. Ensure you are

using the correct Ex documentation for the relevant Ex-approved device. The number of the

related Ex documentation (XA...) is indicated on the nameplate. You can use this Ex

documentation if the two numbers (i.e. in the Ex documentation and on the nameplate) are

identical.

1.2 Document conventions

1.2.1 Safety symbols

Symbol Meaning

DANGER

A0011189-EN

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will

result in serious or fatal injury.

CAUTION

A0011191-EN

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can

result in minor or medium injury.

NOTICE

A0011192-EN

NOTE!

This symbol contains information on procedures and other facts which do not result

in personal injury.

1.2.2 Symbols and notation for certain types of information

Symbol Meaning

A0011193

Tip

Indicates additional information.

A0011194

Reference to documentation

Refers to the corresponding device documentation.

A0011195

Reference to page

Refers to the corresponding page number.

A0011196

Reference to graphic

Refers to the corresponding graphic number and page number.

1., 2., 3. Series of steps

Basic safety instructions iTEMP® TMT82

4 Endress+Hauser

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill the

following requirements:

►Trained, qualified specialists must have a relevant qualification for this specific function and

task

►Are authorized by the plant owner/operator

►Are familiar with federal/national regulations

►Before beginning work, the specialist staff must have read and understood the instructions in

the Operating Instructions and supplementary documentation as well as in the certificates

(depending on the application)

►Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

►Being instructed and authorized according to the requirements of the task by the facility's

owner-operator

►Following the instructions in these Operating Instructions

2.2 Designated use

The device is a universal and user-configurable temperature head transmitter with either one or

two sensor inputs for a resistance thermometer (RTD), thermcouples (TC) or resistance and

voltage transmitters. The device is designed for mounting in a flat-face terminal head as per DIN

43729. Installation on a DIN rail with the optional available DIN rail clip is also possible.

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Operational safety

►Operate the device in proper technical condition and fail-safe condition only.

►The operator is responsible for interference-free operation of the device.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the hazardous

area (e.g. explosion protection):

►Based on the technical data on the nameplate, check whether the ordered device is permitted

for the intended use in the hazardous area. The nameplate can be found on the side of the

transmitter housing.

►Observe the specifications in the separate supplementary documentation that is an integral

part of these Instructions.

Electromagnetic compatibility

The measuring system complies with the general safety requirements in accordance with EN

61010, the EMC requirements of IEC/EN 61326 and NAMUR Recommendation NE 21 and

NE 89.

iTEMP® TMT82 Identification

Endress+Hauser 5

NOTICE

►The unit must only be powered by a power supply that operates using an IEC 61010-1

compliant energy limited circuit, "SELV or Class 2 circuit".

3 Identification

3.1 Device designation

The following options are available for identification of the device:

• Nameplate specifications

•Enter the serial number from the nameplate in W@M Device Viewer (www.endress.com/

deviceviewer): All information about the device and an overview of the technical

documentation supplied with the device is displayed.

3.1.1 Nameplate

The right device?

Compare and check the data on the nameplate of the device against the requirements of the

measuring point:

123

11-42V 012345678910

xx.yy.zz

TMT82- XXXXX/XX

iTEMP®

Made in Germany 2011

D-87484 Nesselwang

Ser.no.:

FW:

Input:

12345678ABCDEFGH

Current consum.: 23,6 mA Dev.Rev: 1

Ext. ord. cd.:

XXXXXXXXXXXXX#

II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C

II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C

EH 08.001X

Install per XA00102R/09/a3/xx.xx

0044

A0014561

å 1 Nameplate of the head transmitter (example, Ex version)

1 Power supply, current consumption and extended order code

2 Serial number, device revision and firmware version

3 Approvals with symbols

4 2 lines for the TAG name

5 Approval in hazardous area with number of the relevant Ex documentation (XA...)

6 Order code

Installation instructions iTEMP® TMT82

6 Endress+Hauser

3.2 Scope of delivery

The scope of delivery of the device comprises:

•Temperature Head Transmitter

• Securing material

• Hard copy of multi-language Brief Operating Instructions

• Operating Instructions and additional documentation on CD-ROM

• Additional documentation for devices which are suitable for use in the hazardous area (0

1), such as Safety Instructions (XA), Control or Installation Drawings (ZD).

3.3 Certificates and approvals

The device left the factory in a safe operating condition. The device complies with the standards

EN 61 010-1 "Protection Measures for Electrical Equipment for Measurement, Control,

Regulation and Laboratory Procedures" and with the EMC requirements of IEC/EN 61326.

3.3.1 CE mark, declaration of conformity

The device therefore meets the legal requirements of the EC guidelines. The manufacturer

confirms a positive completion of all tests by fitting the unit with a CE mark.

3.3.2 HART® protocol certification

The temperature transmitter is registered by HART® Communication. The device meets the

requirements of the HART Communication Protocol Specifications, April 2001, Revision 6.0.

4 Installation instructions

4.1 Incoming acceptance, transport, storage

4.1.1 Incoming acceptance

• Is the packaging or content damaged?

• Is the delivery complete and is anything missing? Check the scope of delivery against your

order.

4.1.2 Transport and storage

• Pack the device in such a way as to protect it reliably against impact for storage (and

transportation). The original packaging provides optimum protection.

• The permitted storage temperature is -40 to +100 °C (-40 to 212 °F).

iTEMP® TMT82 Installation instructions

Endress+Hauser 7

4.2 Installation conditions

4.2.1 Dimensions

24.1 (0.95”)

33 (1.3”)

Ø44 (1.73”)

Ø7 (0.28”)

Ø5 (0.2”)

A0007301

å 2 Version with screw terminals. Dimensions in mm (in)

A Spring travel L ≥ 5 mm (not for US - M4 securing screws)

B Securing elements for attachable measured value display

C Interface for measured value display contact

The same dimensions apply to the version with spring terminals apart from the housing

height H = 28.1 mm (1.11").

4.2.2 Installation point

• In the terminal head as per DIN 43 729, flat face, direct mounting on insert with cable entry,

middle hole 7 mm (0.28").

• Separate from the process in the field housing.

• With DIN rail clip on top-hat rail as per IEC 60715.

4.2.3 Important ambient conditions

Ambient temperature range: -40 to +85°C (-40 to +185 °F).

Condensation permitted as per IEC 60068-2-33; max. rel. humidity: 95%.

Climate class in accordance with IEC 60654-1, Class C.

IP 20 ingress protection, depends on the terminal head or field housing in its installed state.

NOTICE

►When using in the hazardous area, the limit values of the certificates and approvals must be

observed (see Safety Instructions XA or CD).

4.3 Installation instructions

A Phillips head screwdriver is required to mount the head transmitter.

Installation instructions iTEMP® TMT82

8 Endress+Hauser

NOTICE

Do not overtighten the mounting screws as this could damage the head transmitter.

►Maximum torque = 1 Nm (¾ pound-feet).

4.3.1 Mounting

1 2 3 4 5

Item A Item B

Item C

A0014269-EN

å 3 Head transmitter mounting (three versions)

Procedure mounting in a terminal head, item A:

1. Open the terminal head cover (8).

2. Guide the connection wires (4) of the insert (3) through the center hole in the head

transmitter (5).

3. Fit the mounting springs (6) on the mounting screws (7).

4. Guide the mounting screws (7) through the side boreholes of the head transmitter and the

insert (3). Then fix both mounting screws with the snap rings (2).

5. Then tighten the head transmitter (5) along with the insert (3) in the terminal head.

6. After wiring, (® ä 10) close the terminal head cover (8) back on tight.

Procedure mounting in a field housing, item B:

1. Open the cover (1) of the field housing (5).

iTEMP® TMT82 Installation instructions

Endress+Hauser 9

2. Fit the mounting springs on the mounting screws (2) and guide the screws through the

side boreholes of the head transmitter (3). Then fix both mounting screws with the snap

rings (4).

3. Screw the head transmitter to the field housing.

4. After wiring, (® ä 10) screw the field housing cover (1) back on.

Procedure mounting on top-hat rail, item C:

1. Press the DIN rail clip (4) onto the top-hat rail (5) until it engages with a click.

2. Fit the mounting springs on the mounting screws (1) and guide the screws through the

side boreholes of the head transmitter (2). Then fix both mounting screws with the snap

rings (3).

3. Screw the head transmitter (2) onto the DIN rail clip (4).

4.3.2 Mounting typical of North America

123 4 5

A0008520

å 4 Head transmitter mounting

Thermometer design with thermocouples or RTD sensors and head transmitter:

1. Fit the thermowell (1) on the process pipe or the container wall. Secure the thermowell

according to the instructions before the process pressure is applied.

2. Fit the necessary neck tube nipples and adapter (3) on the thermowell.

3. Make sure sealing rings are installed if such rings are needed for harsh environmental

conditions or special regulations.

4. Guide the mounting screws (6) through the lateral bores of the head transmitter (7).

5. Position the head transmitter (5) in the terminal head (4) in such a way that the bus cable

(terminals 1 and 2) point to the cable entry.

Wiring iTEMP® TMT82

10 Endress+Hauser

6. Using a screwdriver, screw down the head transmitter (5) in the terminal head (4).

7. Guide the connection wires of the insert (3) through the lower cable entry of the terminal

head (4) and through the middle hole in the head transmitter (5). Wire the connection

wires and transmitter (® ä 11) with one another.

8. Screw the terminal head (4), with the integrated and wired head transmitter, onto the

ready-mounted nipple and adapter (3).

NOTICE

The terminal head cover must be secured properly to meet the requirements for

explosion protection.

►After wiring, securely screw the terminal head cover back on.

4.4 Post-installation check

After installing the device, always run the following final checks:

Device condition and specifications Notes

Is the device undamaged (visual inspection)? -

Do the ambient conditions match the device specification (e.g. ambient temperature, measuring

range, etc.)?

(® ä 7)

5 Wiring

!CAUTION

►Switch off power supply before installing or connecting the device. Failure to observe this

may result in destruction of parts of the electronics.

►When installing Ex-approved devices in a hazardous area, please take special note of the

instructions and connection schematics in the respective Ex documentation added to these

Operating Instructions. The local Endress+Hauser representative is available for assistance if

required.

►Do not occupy the display connection. An incorrect connection can destroy the electronics.

For wiring a mounted head transmitter, proceed as follows:

1. Open the cable gland and the housing cover on the terminal head or the field housing.

2. Feed the cables through the opening in the cable gland.

3. Connect the cables as shown in (® ä 11). If the head transmitter is fitted with spring

terminals, pay particular attention to the information in the "Connecting to spring

terminals" section .

4. Retighten the cable gland and close the housing cover.

In order to avoid connection errors always take note of the hints given in the section connection

check!

Autres manuels pour iTEMP TMT82

Table des matières

Autres manuels Endress+Hauser Émetteur

Endress+Hauser

Endress+Hauser iTEMP TMT85 Caractéristiques techniques

Endress+Hauser

Endress+Hauser iTEMP TMT111 Manuel utilisateur

Endress+Hauser

Endress+Hauser Promag Series Manuel utilisateur

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Manuel

Endress+Hauser

Endress+Hauser FHX50 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT187 Manuel utilisateur

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys CUM 252 Manuel utilisateur

Endress+Hauser

Endress+Hauser L20221 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Liquisys M COM 223 F Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M CLM223F Manuel utilisateur

Endress+Hauser

Endress+Hauser RMA42 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar S FMD76 Manuel utilisateur

Endress+Hauser

Endress+Hauser Cerabar M Manuel utilisateur

Endress+Hauser

Endress+Hauser CM14 Manuel utilisateur

Endress+Hauser

Endress+Hauser CM14 Manuel utilisateur

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manuel utilisateur

Endress+Hauser

Endress+Hauser CM14-AAK Manuel utilisateur

Endress+Hauser

Endress+Hauser Prosonic S FMU95 Instructions d'utilisation et d'installation

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Instructions d'utilisation et d'installation

Endress+Hauser

Endress+Hauser Liquisys M CLM223F Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT80 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquisys M COM 223 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline 500 HART Caractéristiques techniques

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur

Endress+Hauser iTEMP TMT82 Caractéristiques techniques

Manuels Émetteur populaires d'autres marques