Targus Wireless RF Mouse Manuel utilisateur

BRUSSELS HANNOVER BARCELONA TOKYO MILANO AMSTERDAM SINGAPORE LONDON PARIS NEW YORK LOS ANGELES TORONTO HONG KONG SYDNEY

Wireless RF Mouse

USER’S GUIDE

Making Your Mobile Life Easier.

Visit our Web site at: www.targus.com

400-0120-001B

TARGUS WIRELESS RF

MOUSE

Introduction

Congratulations on your purchase of a Targus Wireless RF

Mouse. This ergonomically designed mouse uses a radio

frequency (RF) link that enables you to use the mouse

anywhere within three feet of its receiver. No line-of-sight

between the mouse and its receiver is required.

This user’s guide describes how to connect the mouse receiver

to your computer, install default software drivers and set up the

radio link.

System Requirements

To use the RF mouse, your computer must meet the following

hardware requirements and run one of the operating systems

listed below.

Hardware

•PCwithanIntel

®Pentium®processor or equivalent and a

hard disk drive

• USB interface

Operating System

• Windows®98/Me/2000/XP

NOTE: The third button and the scrolling wheel only work with

the operating systems listed above. If you use the RF mouse

with a different operating system, it will lose its enhanced

features and function as a standard, two-button mouse.

Targus Wireless RF Mouse

Installing the Batteries

1 Remove the battery cover from the top of the mouse by

pressing the battery cover hinge, located on the bottom of

the mouse, and sliding it off.

Removing the battery cover

2 Insert the supplied batteries, making sure that the positive

(+) and negative (-) ends of each battery match the polarity

indicators inside the battery housing.

WARNINGS: When replacing the batteries, you may use

alkaline or other heavy-duty NiMH batteries. Never combine

an alkaline with a NiMH battery in a device.

Avoid mixing new and used batteries in a device.

3 Slide the battery cover back into position until it “clicks”

firmly into place.

Battery cover hinge

Battery cover

Targus Wireless RF Mouse

Using the Charger Base

For best results, you should charge the RF mouse for at least

four hours before using the mouse.

NOTE: Using the charger base is optional. If you are using the

mouse without the charger base, you may use disposable

batteries.

CAUTION: If you are using the mouse with the charger base,

you must use rechargeable batteries, such as the ones

supplied, to avoid possible damage to the mouse and charger.

To set up the charger base and charge your mouse:

1 Make sure that batteries in the RF mouse are properly

installed.

2 Attach the power adapter to the power jack on the charger

base and plug the power adapter into a power strip or wall

outlet.

3 Place the RF mouse into the charger base.

The status light on the charger base glows while it charges

the mouse’s batteries.

Connecting the Mouse Receiver

To connect the mouse receiver:

1 Turn off your computer.

2 Plug the USB receiver into an available USB port on your

computer.

Targus Wireless RF Mouse

Installing the Device Drivers

Windows®98/Me Operating Systems

1 Turn on your computer.

The Add New Hardware Wizard appears.

If it does not, the operating system has installed the default

driver automatically. No other steps are necessary.

2ClickNext.

The locate driver screen appears.

3SelectSearch for the best driver for your device.

(Recommended) and then click Next.

The wizard searches for the appropriate device driver.

4ClickNext, then Finish to complete the driver installation.

You are now ready to set the radio frequency channel and

establish a communications link between the mouse and its

receiver. See “Establishing a Communications Link” on page 6

Windows®2000/XP Operating Systems

1 Turn on your computer.

The Found New Hardware Wizard appears.

If it does not, the operating system has installed the default

driver automatically. No other steps are necessary.

2ClickNext.

The wizard searches for the appropriate device driver.

3ClickNext, then Finish to complete the driver installation

Targus Wireless RF Mouse

You are now ready to set the radio frequency channel and

establish a communications link between the mouse and its

receiver. See “Establishing a Communications Link” on page 6

Establishing a Communications

Link

After your computer detects the USB receiver and the driver

software is installed, you must establish a communications link

between the mouse and its receiver BEFORE you can use the

mouse. To establish this link, you need to set the identification

code so that the mouse works properly.

Setting the Identification Code

Make sure that your computer is turned on and has detected the

USB receiver before you establish a communications link.

1 Press and release the link button on the receiver.

Sample receiver

The receiver’s status light glows when the receiver is

activated.

2 Press and release the reset button, located on the bottom of

the mouse.

Link button

Targus Wireless RF Mouse

CAUTION: Pressing and holding the reset button longer than

1.5 seconds may cause the mouse to enter power off mode.

See “Mouse Power Management” on page 7.

Sample mouse bottom

The mouse’s red light emitter diode (LED) stops glowing

when you press the reset button and resumes glowing when

the button is released.

You are now ready to use the RF mouse.

Mouse Power Management

To power the mouse off, wake the mouse (if it’s in sleep

mode), press and hold the reset button for at least two seconds.

Then, release the reset button when the red LED flashes one

time.

To power the mouse on, press and release the reset button so

that the red LED glows.

Reset button

Targus Wireless RF Mouse

Operating Hints

For optimal performance and RF reception:

• Place the receiver at least 8 inches (20 cm) away from all

electrical devices, such as your monitor, speakers or external

storage devices.

If necessary, use a three-inch extension cable to place the

receiver away from the computer. Plug the receiver into the

extension cable, and the extension cable to the computer.

• Avoid using the RF mouse on a metal surface. Metals, such

as iron, aluminum or copper, shield the radio frequency

transmission and may slow down the mouse’s response time

or cause the mouse to fail temporarily.

• The RF mouse will enter a suspend mode at the same time

your computer does. To activate the mouse, press any button.

• If your computer has a metal case that contains aluminum or

magnesium, use the RF mouse to the side. The display panel

may interfere with the radio frequency signal if you use the

mouse directly in front of the computer.

• Never use the RF mouse on a glass or mirrored surface as

these surfaces will cause the mouse to fail temporarily.

• To maximize battery life, use the RF mouse on a white, or

light colored surface. Dark surfaces cause the mouse’s light

emitter diode (LED) light to glow brighter, which causes the

battery to discharge more rapidly.

Targus Wireless RF Mouse

Comfortable Usage

Research suggests that physical discomfort and injury to

nerves, tendons, and muscles may be related to repetitive

motion, an improperly set up work area, incorrect body posture

or poor work habits.

To reduce the risk of injury, follow these precautions:

• Stand, stretch, and move around several times every hour.

• Switch hands while performing tasks. Use shortcut keys to

avoid repetitive or awkward mouse movements.

• Relax your shoulders and keep your elbows at your sides.

Adjust the keyboard’s position so that you don’t have to

stretch to reach it.

• Adjust your position so that you don’t have to bend your

wrists to type; avoid placing your wrists on a sharp edge.

If you feel discomfort or numbness in your hands, wrists, arms,

shoulders, neck, or back while typing, consult a qualified

medical professional.

Things to Remember

Batteries

General

• You must establish a communications link every time you

change the batteries.

• To extend the life of your batteries, turn off the mouse by

holding the reset button, located on the bottom of the mouse,

Targus Wireless RF Mouse

for two seconds. See “Mouse Power Management” on

page 7.

• Always synchronize the mouse and its receiver after

changing the batteries.

Sleep Mode

• The mouse’s sleep mode feature activates after 20 minutes of

non-operation.

• The mouse enters sleep mode every time the batteries are

changed.

• To wake the mouse from sleep mode, press any button.

Specifications

Button Count 3 with scrolling wheel

ID Selections 256

Electromagnetic

Characteristics (EMC)

CE - Type acceptance: ETS 300

220 short range devices

Distance Between

Mouse and Receiver up to 3 feet (1 m)

Mouse Carrier Frequency 27 MHz

Dimensions Mouse:

3.86 x 2.32 x 1.5 inches

(98 x 59 x 38 mm)

Receiver:

1.96 x 0.86 x 0.59 inches

(50 x 22 x 15 mm)

Autres manuels pour Wireless RF Mouse

Table des matières

Autres manuels Targus Souris

Targus

Targus AMU76EU Manuel utilisateur

Targus

Targus AMW05CA Manuel utilisateur

Targus

Targus Wireless Mouse Manuel utilisateur

Targus

Targus AMW14EU Manuel utilisateur

Targus

Targus AMB09US Manuel utilisateur

Targus

Targus AMW3001EU Manuel utilisateur

Targus

Targus Stow-N-Go Notebook Mouse Manuel utilisateur

Targus

Targus AMU14EU Manuel utilisateur

Targus

Targus Optical Bluetooth Mouse Manuel utilisateur

Targus

Targus Kaleidoscope AMU0503US Manuel utilisateur

Targus

Targus Wi-Fi mouse Manuel utilisateur

Targus

Targus Stow-N-Go Notebook Mouse Manuel utilisateur

Targus

Targus Wireless Laser Mouse Manuel utilisateur

Targus

Targus AMBS44 Manuel utilisateur

Targus

Targus AMU25 Manuel utilisateur

Targus

Targus AMW05US Manuel utilisateur

Targus

Targus AMU34EU Manuel utilisateur

Targus

Targus AMB581 Manuel utilisateur

Targus

Targus AMW43EU Manuel utilisateur

Targus

Targus Stow-N-Go Notebook Mouse Manuel utilisateur

Targus

Targus AMW839 Manuel utilisateur

Targus

Targus AMW14US Manuel utilisateur

Targus

Targus Stow-N-Go Notebook Mouse Manuel utilisateur

Targus

Targus COMPACT LAPTOP CHARGER Manuel utilisateur

Manuels Souris populaires d'autres marques

Sven

Sven RX-G720 Manuel utilisateur

3DConnexion

3DConnexion CadMouse Pro Manuel utilisateur

Canyon

Canyon Puncher GM-20 Manuel utilisateur

Sharkoon

Sharkoon Light2 180 Manuel utilisateur

Cherry

Cherry MW 8C ERGO Manuel utilisateur

NGS

NGS HIT RB Manuel utilisateur

Sharkoon

Sharkoon FireGlider Manuel utilisateur

Lenovo

Lenovo Wireless Mouse N3902 Manuel utilisateur

BASETech

BASETech BN-S11 Manuel utilisateur

Dell

Dell WM326 Manuel utilisateur

Areson

Areson B213 Manuel utilisateur

HP M17587-371 Manuel utilisateur

Chatpen

Chatpen CHA-30 Manuel utilisateur

GAMDIAS

GAMDIAS DEMETER GMS5000 Manuel utilisateur

HP KJ453AA - Wireless Laser Mouse Manuel utilisateur

Trust

Trust GRAPHIN GXT 960 Manuel utilisateur

Lenovo

Lenovo SD-9082 Manuel utilisateur

Alienware

Alienware AW320M Manuel utilisateur