SIIG SIIG 2-Port Serial 950-Value Manuel utilisateur
1
SIIG 2-Port Serial 950-Value
Quick Installation Guide
04-0354C
Introducing the SIIG 2-Port Serial 950-Value
The SIIG 2-Port Serial 950-Value high-speed serial I/O
card provides two additional 9-pin serial ports.
Features and Benefits
•Conforms to PCI v2.2 Plug and Play
•Can be installed in 32-/64-bit, 3.3v/5v PCI and
PCI-X slots
•Reduces CPU load and improves system
performance dramatically
•Built-in FIFO buffers dramatically increase data
transmit/receive speed, especially under Windows
multitasking environment
•High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial
devices
System Requirements
•Pentium or equivalent PC with an available PCI slot
•Windows®7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000
/ ME / NT4.0 / 98SE / 98 / 95
PackageContents
•SIIG 2-Port Serial 950-Value board
• Driver CD
• Quick installation guide
2
Layout
Figure 1. Layout
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove the computer cover.
4. Remove the slot bracket from an available PCI slot.
5. Carefully align the card's bus connector with the
selected PCI slot on the motherboard. Push the
board down firmly, but gently, until it is well seated.
Serial Port 2
Serial Port 1
3
6. Replace the slot bracket holding screw to secure the
card.
7. Replace thecomputercoverandreconnect thepower
cord.
Software Installation
This section provides information on how to install the
SIIG 2-Port Serial 950-Value drivers.
Windows 7 (32-/64-bit)
1. Right click Computer, click Manage, click Device
Manager.
2. Insert the driver CD. Right click PCI Serial Port,
click Update Driver Software.
3. Click Browse my computer for driver software.
4. Type D:, then click Next. (Change D: to match your
CD/DVD-ROM drive letter)
5. At Windows has successfully updated your driver
software, click Close.
6 Right click Other PCI Bridge Device, click Update
Driver Software.
7. Repeat steps 3-5.
8. Right click CyberSerial Communication Port, click
Update Driver Software.
9. Click Browse my computer for driver software.
10. Type D:, click Next. (Change D: to match your CD/
DVD-ROM drive letter)
11. At Windows has successfully updated your driver
software, click Close.
12. Repeat steps 8-11 to complete the installation.
4
Windows Vista (32-/64-bit)
1. At the Found New Hardware window, insert the
driver CD, click Locate and install driver software
(recommended), click Continue.
2. Click Don't Search Online, Next, then click Close.
3. Repeat step 2to complete the driver installation.
Windows XP (32-/64-bit) / Server 2003 (32-/64-bit)
1. At the Found New Hardware Wizard, insert the
driver CD.
2. Select No, not this time, click Next. (Skip this step
if not prompted)
3. Select Install the software automatically
(Recommended),then click Next.
4. Click Finish.
5. Repeat steps 1-4 two more times.
6. Restart Windows to complete the installation.
Windows Server 2008 (32-/64-bit)
1. At the Found New Hardware Wizard, click Locate
and install driver software (recommended).
2. Insert the driver CD.
3. Click Don't search online.
4. Click I don't have the disc. Show me other options.
5. Click Browse my computer for driver software
(advanced).
6. Type D:, then click Next. (Change D: to match your
CD/DVD-ROM drive letter)
7. AtThe sofware for this device has been sucessfully
installed, click Close.
8. Repeat steps 3-7 to complete the installation.
5
To Verify Windows 7 / Vista / XP / Server 2003 &
2008 Installation
1. Check in Device Manager to verify installation.
For Windows 7: Right click Computer, click Manage,
then click Device Manager.
For Windows Vista: Right click Computer, click
Manage,clickContinue, thenclick Device Manager.
For Windows XP / Server 2003: Right click My
Computer, click Manage, then click Device
Manager.
For Windows Server 2008: Right click Computer, click
Manage,doubleclick Diagnostics,then clickDevice
Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial 950 16Cxxx... should be
displayed two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S board should be displayed.
Windows 2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), then click Next.
3. Check Specify a location, uncheck the other boxes,
then click Next.
4. Insert the driver CD, type in D:\2000, then click OK.
(Change D: to match your CD-ROM drive letter)
5. Click Next and Finish.
6. Repeat steps 1-5 two more times.
7. Restart Windows to complete the installation.
6
To Verify Windows 2000 Installation
1. Right click My Computer, click Manage, then click
Device Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial 950 16Cxxx... should be
displayed two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S board should be displayed.
Windows ME
1. At the Add New Hardware Wizard, select Specify
the location of the driver (Advanced),then click
Next.
2. Insert the driver CD, check Specify a location,
uncheck the other box, type in D:\ME,then click
Next.(Change D: to match your CD/DVD-ROM
drive letter)
3. Click Next, then Finish.
4. Repeat steps 1& 2.
5. Click Next, Next, then Finish.
6. Restart Windows to complete the installation.
Windows 98SE / 98
1. At the Add New Hardware Wizard, click Next.
2. Select Search for the best driver for your device
(Recommend), then click Next.
3. Insert the driver CD, check Specify a location,
uncheck the other boxes, type in D:\9x, then click
Next. (Change D: to match your CD/DVD-ROM
drive letter)
4. Click Next, then Finish.
7
5. Repeat steps 1-4.
6. Restart Windows to complete the installation.
Windows 95
1. At the Update Device Driver Wizard, click Next.
2. Insert the driver CD, click Other Locations.
3. Type in D:\9x, click OK, then click Finish. (Change
D: to match your CD/DVD-ROM drive letter)
4. At the Insert Disk window, click OK. At Copying
Files dialog box, type in D:\9x,then click OK.
(Change D: to match your CD/DVD-ROM drive
letter)
5. Restart Windows to complete the installation.
To Verify Windows ME / 98SE / 98 / 95 Installation
1. Right click My Computer, click Properties,then
click Device Manager.
2. Double click Ports (COM & LPT), CyberSerial 950
16Cxxx... should be displayed two times.
3. Double click Multi-function adapters, SIIG
CyberPro 2S board and PCI Function should be
displayed.
Windows NT 4.0
1. From the desktop click Start, then Run.
2. Insert the driver CD, type in
D:\NT4\Install_serial.exe, then click OK.
(Change D: to match your CD/DVD-ROM drive
letter)
3. At Welcome window, click Next .
4. Select Install, then click Next.
8
5. Click Yes, then click Exit.
6. Restart Windows to complete the installation.
To Verify Windows NT 4.0 Installation
1. Click Start, Settings, Control Panel.Double click
Ports device icon.
2. Two new COM ports will be assigned when
successfully installed.
9
Changing COM Port Address
Some serial devices need a specific COM port in order to
work. If your serial device works properly, do not
change this setting.
Windows 7 / Vista / XP / Server 2003 & 2008 / 2000
1. From the Device Manager window, double click
Ports (COM & LPT), then double click the
CyberSerial serial port you want to change.
2. Click Settings tab, then click Advanced.
3. Click the down arrow that is next to the COM Port
number box and select a COM port that is not in use.
Click OK.
4. Click OK again, then close Device Manager to save
your changes.
Windows ME / 98SE / 98 / 95
1. From the Device Manager window double click
Ports (COM & LPT), then double click the
CyberSerial serial port you want to change.
2. Click Settings tab, click the down arrow that is next
to the Port Name box and select a COM port that is
not in use.
3. Click OK, then close Device Manager to save your
changes.
10
Blank Page
Table des matières
Autres manuels SIIG Matériel informatique
SIIG
SIIG NN-000032-S1 Manuel utilisateur
SIIG
SIIG Dual Profile Hi-Speed USB 4-Port PCI Manuel utilisateur
SIIG
SIIG DP PCI-to-PS/2 Manuel utilisateur
SIIG
SIIG SC-SAE612-S1 Manuel utilisateur
SIIG
SIIG DP PCI-to-PS/2 Manuel utilisateur
SIIG
SIIG NN-8CB212-S1 Manuel utilisateur
SIIG
SIIG FireWire 800 2-Port ExpressCard/34 Manuel utilisateur
SIIG
SIIG JJ-E01111-S1 Manuel utilisateur
SIIG
SIIG DP SoundWave 4 Channel PCI Manuel utilisateur
SIIG
SIIG USB 2.0 5-Port PCI Manuel utilisateur
SIIG
SIIG Serial ATA PCI Manuel utilisateur
SIIG
SIIG JJ-EC2011-S1 Manuel utilisateur
SIIG
SIIG Single-Serial PC Card Manuel utilisateur
SIIG
SIIG CyberParallel Dual Manuel utilisateur
SIIG
SIIG USB 2.0+1394 DV Kit Manuel utilisateur
SIIG
SIIG Parallel Pro Manuel utilisateur
SIIG
SIIG Low Profile USB Adapter Manuel utilisateur
SIIG
SIIG UltraATA 100 Pro Manuel utilisateur
SIIG
SIIG JJ-EC1012-S1 Manuel utilisateur
SIIG
SIIG UltraATA 133 PCI Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
