SIIG Low Profile POS 2000RJ Manuel utilisateur

Low Profile POS 2000RJ

Quick Installation Guide

04-0241A

Introducing the

Low Profile POS

2000RJ

TheLow Profile POS 2000RJis a high-speed plug-n-play PCI bus serial

I/O card that provides 5V or 12V DC output.

Features and Benefits

•Provides two RJ45 high-speed serial ports which can be

individually configured as standard RS232 serial ports or RS232

serial ports with 5V/12V DC output

• Supports both 8-pin and 10-pin RJ45 cable for device connections

•Conforms to PCI v2.2 Plug and Play

•Full support for DOS and Windows based applications

•Improves I/O access speed up to 8 times faster than existing

ISA-bus serial ports. Reduces CPU load and improves system

performance dramatically

•IRQ sharing feature eliminates IRQ conflicts

•Works with 56K V.90 external modems, ISDN terminal adapters,

PDAs, digital cameras, label printers and other serial port devices

•Built-in 16-byte (32-byte for 16650 model, 128-byte for 16850

model) FIFO buffers dramatically increase data transmit/receive

speed, especially under Windows multitasking environment

System Requirements

•Pentium or equivalent computer with an available 32-bit PCI slot

•DOS/Windows 3.1x, Windows 95/98/98 SE/ME/NT 4.0/2000/

Package Contents

• One Low Profile POS 2000RJ board

• One Driver Installation diskette

• One 5-year warranty card

• This quick installation guide

Hardware Installation

General instructions for installing the card are provided below,

since the design of computer cases and motherboards vary. Refer

to your computer’s reference manual for further information, if

needed.

Caution: Static Electricity Discharge may permanently damage

your system. To avoid possible static electricity discharge during

the installation, please follow the guidelines below:

•Dischargeanystaticelectricitybuildupinyourbodyby

touchingalargegroundedmetalsurfaceorthecomputer’scase

(ifpluggedin), forafewseconds.

•During the installation, avoid any contact with internal parts.

Handle cards only by their external edges.

1. Turn OFF the power to your computer and any other

connected peripheral devices.

2. Unplug the power cord from the back of the computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. To install the card, carefully align the card's bus connector

with the selected PCI slot on the motherboard. Push the board

down firmly, but gently, until it is well seated.

6. Replace the slot bracket's holding screw to secure the card.

7. Replace the computer cover and reconnect the power cord.

Pin Definition, Jumper Settings and Layout

RJ45 10-Pin Pin Definition

Pin#12345678910

Signal RI or

5/12V

DC DSR RTS CD or

5/12V

DC TX RX Signal

GND CTS DTR Case

GND

RJ45 8-Pin Pin Definition

Pin#12345678

Signal DSR RTS CD or

5/12V

DC TX RX Signal

GND CTS DTR

Standard RS-232 DB9 pin Definition

Pin#123456789

Signal CD RX TX DTR GND DSR RTS CTS RI

RI Pin Jumper Settings

Key: O=Open, S= Short, -=N/A

Port Mode JP1 JP2 JP3 JP4 JP5

Port1RI-O---

Port 2 RI - - O - -

Port 1 5V 1-2 S S - - -

Port 2 5V 1-2 S - S - -

Port 1 12V 2-3 S S - - -

Port 2 12V 2-3 S - S - -

CD Pin Jumper Settings

Key: O=Open, S=Short, -=N/A

Note: Only one voltage output can be selected at a

time. Thereisnosupportformixedvoltageoutput in

thiscard. Forexample,selectingPort1DC5VandPort

2 DC12V is not supported.

Board Layout

JP2

JP1 JP3

JP5

JP4

Port Mode JP1 JP2 JP3 JP4 JP5

Port1CD---O-

Port2CD----O

Port 1 5V 1-2 S - - S -

Port 2 5V 1-2 S - - - S

Port 1 12V 2-3 S - - S -

Port 2 12V 2-3 S - - - S

Jumper Description

•JP1: Select 5V/12V when voltage output is selected

• JP2: Select RI/voltage output for Port1

• JP3: Select RI/voltage output for Port2

•JP4: Select CD/voltage output for Port1

•JP5: Select CD/voltage output for Port2

Software Installation

This section provides information on how to install the

Low Profile POS 2000RJ drivers for the following operating systems:

Windows 95b/98/98 SE/ME

Windows NT 4.0

Windows 2000

Windows XP

DOS/Windows 3.1x

Windows 95b Driver Installation

1. At the Update Device Driver Wizard window, click Next.

2. Insert the Driver Installation diskette in the floppy drive, and

click Other Locations. Type in a:\Win95, click OK, then

Finish.

3. From the Insert Disk window, click OK. When the Copying

Files dialog box appears, type in a:\Win95, then click OK.

4. Remove the diskette and select Yes to restart the computer for

the setup to take effect.

Windows 98/98 SE Driver Installation

1. At the Add New Hardware Wizard window, click Next.

2. Select Search for the best driver for your device

(Recommend), then click Next.

3. Select Specify a location, insert the Driver Installation diskette

and type in a:\Win98, then click Next.

4. Click Next, then Finish.

5. Remove the diskette and click Yes to restart your system.

Windows ME Driver Installation

1. At the Add New Hardware Wizard screen, choose Specify the

location of the driver (Advanced), then click Next.

2. Check Specify a location, insert the Driver Installation diskette

into your floppy drive, type in A:\Win98, then click Next.

3. Click Next, and Finish to complete driver installation.

4. Remove the driver diskette and click Yes to restart Windows.

To verify successful installation in Windows 95/98/98 SE/ME:

1. From the main desktop, double click My Computer, Control

Panel,System,then click Device Manager.

2. Double click Ports (COM & LPT) and new Cyber PCI ports

should be displayed. Also, double click SIIG Cyber PCI

option and SIIG ... PCI Board should be displayed.

The board is ready to connect new devices.

Windows NT 4.0 Driver Installation

1. From the desktop click Start, then Run.

2. Insert the Driver Installation diskette, type in A:\NT4\setup,

then click OK.

3. Click Next when the Welcome window appears.

4. From Choose Destination Location window, click Next.

5. Remove the Driver Installation diskette, select Yes to restart

Windows and click Finish.

To verify successful installation in Windows NT 4.0:

1. Go to Start / Setting / Control Panel,double click SIIG Cyber

PCI 20X device icon.

2. New COM port address and LPT number will be assigned for

the ports when successfully installed. The board is ready to

connect devices.

To change the I/O address in Windows NT 4.0:

1. Double click Start, Settings, Control Panel,then SIIG Cyber

PCI 20X device icon.

2. Highlight the LPT or COM address and click Settings.

3. Select or type in an I/O address supported by the device you

would like to configure and click OK. Make sure the selected

I/O address does not conflict with other device in your system.

4. Select Restart Now for the new setup to take effect.

Windows 2000 Driver Installation

1. At the New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device

(recommended) and click Next.

3. Select Specify a location, uncheck the other options and click

Next.

4. Insert the Driver Installation diskette, type in A:\Win2K and

click OK.

5. Click Next and Finish to complete driver installation.

Windows XP Driver Installation

1. At the Found New Hardware Wizard select Install from a list

or specific location (Advanced), then click Next.

2. Insert the Driver Installation diskette, check Include this

location in the search, type in A:\Win2K and click Next.

3. Click Continue Anyway and Finish.

4. Repeat steps 1-3 two more times.

5. Restart the computer to complete the installation.

To verify successful installation in Windows 2000/XP:

1. Double click My Computer, Control Panel, System, Hardware,

and click Device Manager.

2. Click on the + (plus sign) in front of Ports (Com & LPT).

3. New Cyber port(s) should be listed.

DOS/Windows 3.1x Driver Installation

1. Insert the Driver Installation diskette, from the C: prompt, type

in copy a:\dos\*.*,then press <Enter>.

2. Type in edit autoexec.bat, then press <Enter>.

3. Add C:\CB20XPC.exe at the bottom of the autoexec.bat file.

4. Go to File, save the changes and exit.

5. Remove the diskette and restart the system for the new setup to

take effect.

Technical Support

QUESTIONS? SIIG’s Online Support has the answers! Simply

visitourweb site at

www.siig.com

and click onSupport/Drivers.

Our online support database is updated daily with new drivers

and solutions. The answers to your problems could be just a few

clicks away.

Return Merchandise Authorization (RMA)

SIIGwarrantstotheoriginalbuyeroftheproductthatthehardware

isfree ofdefectsinmaterialsandworkmanshipforaperiodofone,

twoorfiveyearsfromthe date of purchase. Ifyourproductfailsto

be in good working order during the warranty period, you may

return it to SIIG for repair or replacement at SIIG's option.

To return the product, you need to follow these steps.

Step 1: Contact SIIG's RMA Department

ToobtainanRMAnumber,SIIG'sRMADepartmentcanbereached

by phone at (510)413-5333 or fax at (510)657-5962 or email at

[email protected]. In order to issue an RMA number, the product

serialnumber isrequired. Thisnumbercanbefoundonthesideof

the box and on the back of the product.

Step 2: Complete the RMA form

• FilloutyourReturnMerchandiseAuthorization(RMA)form,and

include it in the package with the product.

• Properlypacktheproductforshipping. Allsoftware,cable(s)and

other accessories that came with the original package must be

included.

• ClearlywriteyourRMAnumberonthetopofthereturnedpackage

and on the accompanying RMA form.

SIIGwillrefusetoacceptanyshipping package, and willnot

beresponsibleforaproductreturnedwithoutanRMAnumber

posted on the outside of the shipping carton.

Step 3: Ship the Product

You are responsible for the cost of shipping back to SIIG at the

following address:

SIIG, Inc. RMA#_______________

6078 Stewart Ave.

Fremont, CA 94538

SIIGwillshiptherepaired or replaced productviaUPSGroundor

US Mail at no cost to you.

PRODUCTNAME MODEL NUMBER

Low Profile POS 2000RJ LP0433

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B

OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a

ClassB digitaldevice,pursuant topart15 oftheFCC Rules.These limitsare

designed to provide reasonable protection against harmful interference in a

residentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio

frequency energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However,thereisnoguaranteethatinterference willnotoccurinaparticular

installation. If this equipment does cause harmful interference to radio and

television reception, which can be determined by turning the equipment off

andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormore

of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio or TV technician for help

Caution:

Any changes or modifications not expressly approved by the party

responsibleforcompliancecouldvoid theuser'sauthoritytooperate

this equipment

THE PARTY RESPONSIBLE FOR

PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

Low Profile POS 2000RJ is a trademark of SIIG, Inc.

SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows

NT are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of

Intel Corporation. Other names used in publication are for identification only and may be

trademarks of their respective companies.

Table des matières

Autres manuels SIIG Matériel informatique

SIIG

SIIG FireWire 800 + Hi-Speed USB Combo Manuel utilisateur

SIIG

SIIG ExpressCard/54 CF R/W Manuel utilisateur

SIIG

SIIG JJ-PCM012-S2 Manuel utilisateur

SIIG

SIIG SC-SE6412 Manuel utilisateur

SIIG

SIIG CE-H23J11-S1 Manuel utilisateur

SIIG

SIIG NN-PC8312-S2 Manuel utilisateur

SIIG

SIIG 1 FireWire 800 CardBus DV-Ki Manuel utilisateur

SIIG

SIIG UltraATA 100 Pro Manuel utilisateur

SIIG

SIIG JU-P40311-S1 Manuel utilisateur

SIIG

SIIG Cyber I/O PCI Manuel utilisateur

SIIG

SIIG 104-0487A Manuel utilisateur

SIIG

SIIG UltraATA 133 PCI Manuel utilisateur

SIIG

SIIG Parallel PCI 1P Manuel utilisateur

SIIG

SIIG UltraATA 133 PCI Manuel utilisateur

SIIG

SIIG ExpressCard 11-in-1 Reader/Writer Manuel utilisateur

SIIG

SIIG NN-PCMM12-S3 Manuel utilisateur

SIIG

SIIG JU-P40412-S1 Manuel utilisateur

SIIG

SIIG ExpressCard/54 CF R/W Manuel utilisateur

SIIG

SIIG AV-GM0AK3-S1 Manuel utilisateur

SIIG

SIIG US2273 Manuel utilisateur

SIIG

SIIG I/O Expander 2S Manuel utilisateur

SIIG

SIIG CyberParallel ExpressCard Manuel utilisateur

SIIG

SIIG JU-EP0012-S1 Manuel utilisateur

SIIG

SIIG DP FireWire 800 PCIe Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur