Pickering 40-582A Manuel utilisateur

pickeringtest.com

Issue 1.2 March 2021

40-582A User Manual

PXI 2 A 2-Pole High Density Matrix Module

Page (II) 2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) 2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description..........................................................2.1

Section 3

Installation....................................................................................3.1

Pre Operation Checks...........................................................3.1

Hardware Installation ............................................................3.2

Software Installation .............................................................3.2

Testing Operation ..................................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options for PXI Modules ..............................4.1

Programming The Matrix ......................................................4.2

Using IVI Driver, Direct I/O Driver or VISA Driver ...............4.3

Section 5

Connector Information................................................................5.1

Section 6

Troubleshooting ..........................................................................6.1

Section 7

Maintenance Information............................................................7.1

Switching System Test Tools ...............................................7.1

Relay Look-Up Tables ...........................................................7.1

CONTENTS

Page (VI) 2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering

Page (VII)

2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O

signals that may be present. Blanking panels are available to order from Pickering in a variety of

slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.

This module must not be used for the switching of Mains Circuits. For the switching of voltages up

to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must

be fully isolated from the Mains Circuit and the safety earth.

The host chassis must be correctly installed and be connected to mains or factory safety ground,

please refer to your chassis installation manual.

Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT

For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage

Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved

by a transformer in which the primary windings are separated from the secondary windings by

reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

PXI Switching

Module

Device

Under Test

Power

Supply

Power

Supply

Host Chassis

Secondary Circuit

Mains

Circuit

Mains

Circuit

Mains/Factory

Safety Ground

Page (VIII) 2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering

Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page 1.1

2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

PXI 2-Pole High Density Matrix Module 40-582A

ISSUE 1.1 MAR 2021

yHigh Density Single-Slot 3U PXI 2-Pole Matrix With

256 Crosspoints

y16x16 Matrix Conﬁguration

yMaximum Current 2 A Hot or Cold Switching

ySwitch up to 270 VDC/225 VAC and up to 60W Max

Power

yUses Gold-Plated Contact Electro-mechanical

2-Pole Relays

yVISA, IVI & Kernel Drivers Supplied for Windows

ySupported by PXI or LXI Chassis

ySupported by

BIRST

™ and

eBIRST

™ Test Tools

y3 Year Warranty

The 40-582A is 256 crosspoint PXI matrix with dual pole

switching. The matrix conﬁguration is 16x16 using 2-pole

electro-mechanical relays with 2 A current handling.

The module is designed for switching medium voltage

and power signals, typical applications include signal

routing in ATE and data acquisition systems. The user

signal connections are via a 78-pin D-type connector that is

fully supported by our wide range of cable and connector

accessories.

Built-In Relay Self-Test -

BIRST

The BIRST facility provides a quick and simple way of

ﬁnding relay failures. No test equipment is required, simply

disconnect the UUT from the module’s connectors, launch

the BIRST application and the tool will run a diagnostic test

that will ﬁnd all relays with faulty contacts.

For more information go to: pickeringtest.com/birst

Supported by

eBIRST

In addition to BIRST, these modules are also supported

by our eBIRST test tools. These tools simplify switching

system fault-ﬁnding by quickly testing the system and

graphically identifying the faulty relay.

For more information go to: pickeringtest.com/ebirst

X10

X12

X16

X11

X13

X14

X15

Y10

Y12

Y16

Y11

Y13

Y14

Y15

2-POLE

CROSSPOINT

40-582A-001 2-Pole 16x16 Matrix

Pickering’s Range of 256 Crosspoint 2 A PXI Matrices

Matrix Size Poles Max Current Model No.

64x4 22 A 40-583-001

32x8 40-580-001

16x16 2 2 A 40-582A-001

128x2

12 A

40-584-001

64x4 40-585A-001

32x8 40-586B-001

16x16 40-587A-001

Page 1.2 2 AMP 2-POLE HIGH DENSITY MATRIX MODULE 40-582A

pickering

SECTION 1 - TECHNICAL SPECIFICATION

2-Pole High Density Matrix, 40-582A

pickeringtest.com

Speciﬁcations

Switching Speciﬁcation

Switch Type: Electro-mechanical

Contact Type: Palladium-Ruthenium,

Gold plated, bifurcated

Max Switch Voltage: 270 VDC/225 VAC*

Max Power:

Max Switch Current:

Max Continuous Carry Current:

Max Pulsed Carry Current Example

(for a single switch path):

60 W/62.5 VA

2 A

6 A for 100 ms

(up to 10 % duty cycle)

Initial On Path Resistance:

Off Path Resistance:

Differential Thermal Offset:

<0.5 Ω

>109 Ω

<10 µV

Max Number of Simultaneously

Closed Crosspoints:

100

Typical Operate Time: 3 ms

Expected Life (Operations)

Very low power load:

Low power load:

Medium power load:

Full power load:

>1x108

>1.5x107 (0.1 A 20 VDC)

>5x106 (1 A 30 VDC)

>1x105 (2 A 30 VDC)

* For full voltage rating, signal sources to be switched

must be fully isolated from mains supply and safety earth.

RF Speciﬁcation

Bandwidth (-3 dB):

Bandwidth (VSWR 1.5:1):

24 MHz (typical)

5 MHz (typical)

Crosstalk (typical): 10 kHz:

100 kHz:

1 MHz:

10 MHz:

-80 dB

-60 dB

-40 dB

-20 dB

Isolation (typical): 10 kHz:

100 kHz:

1 MHz:

10 MHz:

90 dB

80 dB

60 dB

40 dB

Power Requirements

+3.3 V +5 V +12 V -12 V

400 mA 1.1 A 65 mA 0

Operating/Storage Conditions

Operating Conditions

Operating Temperature:

Humidity:

Altitude:

0 °C to +55 °C

Up to 90 % non-condensing

5000 m

Storage and Transport Conditions

Storage Temperature:

Humidity:

Altitude:

-20 °C to +75 °C

Up to 90 % non-condensing

15000 m

PXI & CompactPCI Compliance

The module is compliant with the PXI Speciﬁcation 2.2.

Local Bus, Trigger Bus & Star Trigger are not implemented.

Uses a 33 MHz 32-bit backplane interface.

Safety & CE Compliance

All modules are fully CE compliant and meet

applicable EU directives: Low-voltage safety EN61010-

1:2010, EMC Immunity EN61326-1:2013, Emissions

EN55011:2009+A1:2010.

Mechanical Characteristics

Single slot 3U PXI (CompactPCI card).

Module weight: 410 g.

3D models for all versions in a variety of popular ﬁle

formats are available on request.

Connectors

PXI bus via 32-bit P1/J1 backplane connector.

Front panel signals via 78-pin male D-type connector

For pin outs please refer to the operating manual.

Table des matières

Autres manuels Pickering Unité de contrôle

Pickering

Pickering 40-331 Manuel utilisateur

Pickering

Pickering PXI BRIC 40-569 Manuel utilisateur

Pickering

Pickering 40-581 Manuel utilisateur

Pickering

Pickering BRIC Series Manuel utilisateur

Pickering

Pickering PXi 41-720 Manuel utilisateur

Pickering

Pickering 40-670 Manuel utilisateur

Pickering

Pickering PXI BRIC 40-595A Manuel utilisateur

Pickering

Pickering 40-520 Manuel utilisateur

Pickering

Pickering PXI BRIC 40-562A Manuel utilisateur

Pickering

Pickering 40-252 Manuel utilisateur

Pickering

Pickering 40-574 Manuel utilisateur

Pickering

Pickering 4 785C Series Manuel utilisateur

Pickering

Pickering 45-541 Manuel utilisateur

Pickering

Pickering PXI 40-535 Manuel utilisateur

Pickering

Pickering 4x-585A Manuel utilisateur

Pickering

Pickering 40-727 Manuel utilisateur

Pickering

Pickering 40-582 Manuel utilisateur

Pickering

Pickering 40-191B Manuel utilisateur

Pickering

Pickering 40-534 Manuel utilisateur

Pickering

Pickering 40-592A Manuel utilisateur

Pickering

Pickering 40-519B Manuel utilisateur

Pickering

Pickering Pxi 41-182A Manuel utilisateur

Pickering

Pickering PXI 40-664A Manuel utilisateur

Pickering

Pickering 41-180 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur