Pickering PXi 41-720 Manuel utilisateur

Page 1

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

Issue 6.7 July 2018

User Manual

Isolated Power Supply

Module

(Model No. 41-720)

pickeringtest.com pickering

Page ii

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page iii

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page iv

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page v

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

Technical Support and Warranty................................................iii

Product Safety .............................................................................iv

Contents (this page)....................................................................v

Warnings and Cautions ..............................................................vii

Section 2

Technical Description ........................................................ 2.1

Functional Description................................................. 2.1

Maximum Frequency of Operations at Full Load ...............2.1

Section 3

Installation........................................................................... 3.1

Hardware Installation ................................................... 3.1

Software Installation .................................................... 3.2

Soft Front Panel Installation........................................ 3.2

Section 4

Programming Guide........................................................... 4.1

Programming Options For Pickering PXI Cards........ 4.1

41-720 Module Architecture......................................... 4.2

Programming The 41-720 Module............................... 4.3

Using Pickering Drivers in LabVIEW .......................... 4.4

Using The Soft Front Panel ......................................... 4.5

Section 5

Connector Information....................................................... 5.1

Section 6

Trouble Shooting ................................................................ 6.1

Section 7

Maintenance Information................................................... 7.1

Software Update ........................................................... 7.1

Hardware Maintenance ................................................ 7.1

CONTENTS

Page vi

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

THIS PAGE INTENTIONALLY BLANK

Page vii

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

Page (VII)

REED RELAY MODULE 40-110/115/120/125

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the PXI/LXI chassis are populated with blanking plates to prevent access to user

I/O signals that may be present. Blanking panels are available to order from Pickering in a variety

of slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page viii

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

THIS PAGE INTENTIONALLY BLANK

SECTION 1 - TECHNICAL SPECIFICATION

Page 1.1

pickering

PXI ISOLATED POWER SUPPLY MODULE 41-720

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

The 41-720 Isolated Power Supply module provides

ﬁxed output voltage power supplies suitable for

powering devices under test that have a medium power

consumption. The module is ideal for providing ﬁxed

voltages to the device under test and can signiﬁcantly

reduce the space needed by the test system by

eliminating the bench power supply from the system.

The output voltages are fully isolated from the chassis

and can be used as ﬂoating outputs referenced to a DC

pedestal voltage.

The module can be supplied with a variety of voltage

options, each module having up to one isolated bipolar

output and two isolated single output voltages.

The bipolar output provides two output voltages, one

positive and one negative, referenced to a common

output terminal. The outputs can be used in series for

higher voltage applications. All single output voltages

can be used to provide a positive or a negative output

by simply using either the negative or the positive

output as the reference.

The voltage regulators use a switch mode pulse width

modulated regulator that can operate at up to 80%

efﬁciency

to preserve

the available

power from the

chassis.

CONTROL

PXI

INTERFACE

ISOLATED

BIPOLAR

POWER SUPPLY

ISOLATED

POWER SUPPLY

ISOLATED

POWER SUPPLY

V+

V-

COMMON

V+

COMMON

V+

COMMON

+5V PXI SUPPLY

41-720

Isolated Power Supply

●One Slot Module Provides up to 4 Regulated Output

Voltages

●Short Circuit and Thermally Protected

●Power On/Off Control for Each Regulated Output

●Output Voltages of 5V and 12V Available

●Bipolar Output can be Used to Provide 24V

●Output Isolated From The PXI Power Supply

●Fully Floating Operation

●Available With D-Type Plug or 1mm Sockets

●VISA Drivers Supplied for Windows

Plus Soft Front Panel

●2 Year Warranty

41-720 Soft Front Panel

41-720 Schematic Overview

ISSUE 7.0 OCT 2017

Page 1.2

SECTION 1 - TECHNICAL SPECIFICATION

PXI ISOLATED POWER SUPPLY MODULE 41-720

pickering

pickeringtest.com

Width and Dimensions

Occupies 1 slot of a 3U PXI chassis

Connectors

Power supply outputs are carried either on a 9-pin male

D-type connector or 1mm sockets, the allocation of pins to

supply rails is determined by the order number. The connector

type is speciﬁed by the part number sufﬁx.

PXI bus via 32 bit P1/J1 backplane connector.

Electrical Speciﬁcation

Each module is ﬁtted with up to one bipolar output and two

single output power supplies.

Isolation Voltage

The outputs are fully isolated, maximum common mode

output voltage of 500 Volts

Power Supply Control

Each regulator can be independently turned on or off.

Bipolar Output

One ﬁtted to each module, deﬁned by xx option

Product Order Codes

For each module select one bipolar output option and two

single output voltages. Order code is constructed as:

41-720-XX-YY-ZZ-D for 9-pin D-type output connector

41-720-XX-YY-ZZ-B for 1mm socket output connectors

where XX is the option number of the bipolar output

where YY is the option number for the ﬁrst single output

and ZZ is the option number of the second single output

Allowed XX options:

Option 00 Not ﬁtted

Option 02 ±12 Volts

Allowed YY and ZZ options:

Option 00 Not ﬁtted

Option 11 5 Volts

Option 12 12 Volts

Pricing for this part is based on how many of the optional

supplies are ﬁtted. If only two are ﬁtted the price is as the

“partial loaded” version, if all three are supplied it is as the

“fully loaded” part.

Mating Connectors & Cabling

For connection accessories for the 41-720 module please

refer to the 90-003D 9-pin D-type Connector Accessories

data sheet where a complete list and documentation can be

found for accessories.

Version Option

Output voltage

(referenced to common) ±12V

Maximum Output Current

(each output) 0.625A

Ripple Voltage (peak

to peak) at maximum

current (typical, no added

capacitive load)

130mV

Load Regulation

(at 10% minimum load) 1%

Version Option

Option

Output voltage

(referenced to common) 5V 12V

Maximum Output Current

(each output) 1.6A 0.665A

Ripple voltage (peak to peak) at

maximum current (typical, no

added load capacitor)

50mV 130mV

Load Regulation

(at 10% minimum load) 0.5%

Power Consumption

No current is taken from the PXI +3.3V supply or the ±12 Volt

supplies.

Current required from +5V PXI supply:

All regulators off: 100 mA

Additional current (each) at full load

Option 02 3.75 Amps

Option 11 & 12 2.1 Amps

Module current consumption should be limited to 6 Amps

for chassis meeting only the minimum requirements of PXI

speciﬁcation version 2.1.

Single Outputs

Any two options ﬁtted to each module, including two of the

same, deﬁned by yy and zz options.

Table des matières

Autres manuels Pickering Unité de contrôle

Pickering

Pickering 40-521 Manuel utilisateur

Pickering

Pickering 40-534 Manuel utilisateur

Pickering

Pickering Module Manuel utilisateur

Pickering

Pickering PXI 41-181 Manuel utilisateur

Pickering

Pickering 41-735 Manuel utilisateur

Pickering

Pickering 40-297A Manuel utilisateur

Pickering

Pickering SYSTEM 10 Manuel utilisateur

Pickering

Pickering 40-252 Manuel utilisateur

Pickering

Pickering 41-765 Manuel utilisateur

Pickering

Pickering SYSTEM 10 Manuel utilisateur

Pickering

Pickering 40-880 Manuel utilisateur

Pickering

Pickering SYSTEM 10 Manuel utilisateur

Pickering

Pickering 40-618A Manuel utilisateur

Pickering

Pickering 40-565A Manuel utilisateur

Pickering

Pickering PXI 40-664A Manuel utilisateur

Pickering

Pickering BRIC Series Manuel utilisateur

Pickering

Pickering 40-519A Manuel utilisateur

Pickering

Pickering 40-581 Manuel utilisateur

Pickering

Pickering PXI 40-785 Manuel utilisateur

Pickering

Pickering 4 890 Series Manuel utilisateur

Pickering

Pickering PXI 30 A Manuel utilisateur

Pickering

Pickering 4x-727A Manuel utilisateur

Pickering

Pickering 40-262 Manuel utilisateur

Pickering

Pickering PXI 40-597 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur