PEERLESS PLA 60 and assembly Mode d’emploi

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06

Models: PLA 60, PLA 60-S,

PLAV 60, PLAV 60-S

Installation and Assembly - Articulating Swivel Arm for

37" - 60" Plasma Screens

Maximum UL Load Capacity:175 lb (79 kg)

This product is UL Listed. It must be

installed by a qualified professional

installer.

2 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06

Read instruction sheet before you start installation and assembly.

Installations:

To Wood Stud Walls ...................................................................................................... page 4

To Concrete Walls .......................................................................................................... page 5

IMPORTANT! Turn to the appropriate page for your wall installation.

• DonotbegintoinstallyourPeerless product until you haveread and understood the instructionsand warnings

containedin this Installation Sheet. Ifyou have any questions regardingany of the instructionsorwarnings, please

callPeerless customercareat 1-800-729-0307.

• Thisproduct should only beinstalled by aqualified professional.

• Makesurethat the supporting surface will safelysupport the combined load of theequipmentand all attached hard-

wareand components.

• Neverexceed the Maximum ULLoad Capacity of 175lb (79 kg).

• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal

studs (contact customer care). Metal stud installation is not UL evaluated.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgeto edge" stud finderis highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrews and nutsfirmly, but donot overtighten. Overtightening candamage the items,greatly reducing their

holdingpower.

WARNING

Tools Needed for Assembly

•studfinder("edge to edge" stud finder isrecommended)

•drill

•7/32" drill bit for wood studs

•5/16" masonry drill bit for concrete

•7/16"socket wrench with extension (recommended)

•level

•phillipsscrewdriver

Accessories

•External Wall Plate (WSP716, WSP716-S, WSP724, WSP724-S)

(MetalStudnot evaluated by UL)

WALLCONSTRUCTION ADDITIONAL HARDWARE REQUIRED

Wood Stud, Wood Beam none

Concrete none

Metal stud WSP716, WSP716-S, WSP724, or WSP724-S

Other or unsure? Contact Customer Care

IMPORTANT! Certain types of walls require additional mounting hardware...

3 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06

Before you start make sure all parts

listed are included with your product.

Parts List

Some parts may appear slightly different than illustrated.

PLA 60 PLA60-S PLAV 60 PLAV 60-S

DESCRIPTION QTY. PART# PART# PART# PART#

Awallplate 1 201-1040 201-4040 201-1040 201-4040

Btilt-roll assembly 1 201-1093 201-4093 201-1048 201-4048

Carmassembly 1 201-1072 201-4072 201-1049 201-4049

Dwallsupport arm axle 1 201-1041 201-1041 201-1041 201-1041

Evinyltrim 3 600-1012 600-1012 600-1012 600-1012

FM10 x 1.5 x 15 mm screw bolt 8 520-9262 520-9262 520-9262 520-9262

G.505 x .75 x .062" nylon washer 1 540-1074 540-1074 540-1074 540-1074

Htilt adjustment knob 1 560-0108 560-0108 560-0108 560-0108

Icarriage bolt 3/8"-16 x 3.25" 1 520-1315 520-1315 520-1315 520-1315

J1.525 x 2 x .062" delrin washer 2 540-1070 540-1070 540-1070 540-1070

K#8-32 x .375" socket head cap screw 1 520-1210 520-1210 520-1210 520-1210

Lplastic finishing cap 8 590-1123 590-1123 590-1123 590-1123

Mholdingpin 1 580-1166 580-1166 580-1166 580-1166

Nretainerplug 1 590-1007 590-1007 590-1007 590-1007

O5/16 x 3" wood screw 8 520-1243 520-1243 520-1243 520-1243

P.250 x 1 x .068" washer 8 540-1063 540-1063 540-1063 540-1063

Q9/64"allenwrench 1 560-9728 560-9728 560-9728 560-9728

Rcablemanagementclips 4 590-1166 590-1166 590-1166 590-1166

Scable tie 4 590-1168 590-1168 590-1168 590-1168

T36"polyestermeshsleeve 1 600-1015 600-1015 600-1015 600-1015

U6 mm allen wrench 1 560-9716 560-9716 560-9716 560-9716

V10mmallen wrench 1 n/a n/a 560-9727 560-9727

Wanchor 8 590-1025 590-1025 590-1025 590-1025

4 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06

• Installermust verify that thesupporting surface will safelysupport the combined loadof the equipment andall attached

hardwareandcomponents.

• Tightenwood screws so thatwall plate isfirmlyattached, but donot overtighten. Overtightening candamage the

screws,greatly reducingtheirholding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal

studs (contact customer care). Metal stud installation is not UL evaluated.

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovided is forattachment of mountthrough standard thickness drywallor plaster intowood studs. Installers

areresponsible toprovide hardware forother typesof mounting situations.

• Neverexceed the Maximum ULLoad Capacity of 175lb (79 kg).

WARNING

Installation to Wood Stud Wall

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the

studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line

down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be located .36"

above the desired screen center for PLA60 and PLA60-S and .43" below the desired screen center for PLAV 60

and PLAV 60-S. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting

holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level,

secure it using eight 5/16x 3"wood screws (O) and washers (P).

Skip to step 2 on page 6.

• Never mount this product to metal studs without the

requiredaccessory.

WARNING

5 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06

IMPORTANT!Concretemustbe2000psidensity

minimum.

Use wall plate (A), making sure that it is level, as a

template to mark holes. The top mounting slots should

be located .36" above the desired screen center for PLA

60 and PLA 60-S and .43" below the desired screen

center for PLAV 60 and PLAV 60-S. Use the masonry bit

to drill 5/16" (8 mm) dia. holes to a minimum depth of 3"

(76 mm). Insert anchors in holes flush with wall as shown

(right).Placewall plate(A)overanchors (W)and secure

with 5/16 x 3" wood screws (O) and washers (P).

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardwareandcomponents.

• Neverexceed the Maximum ULLoad Capacity of 175lb (79 kg).

• Never mount this product to metal studs.

WARNING

• Always attach concrete expansion anchors directly to

load-bearingconcrete.

• Neverattach concrete expansionanchors toconcrete

coveredwith plaster,drywall, orotherfinishing mate-

rial.If mounting toconcrete surfaces covered witha

finishingsurface isunavoidable, thefinishing surface

mustbe counterbored asshown below. If plaster/

drywall is thicker than 5/8", custom fasteners must be

suppliedby installer (Notevaluated by UL).

WARNING

• Tighten wood screws so that wall plate is firmly

attached,but donot overtighten.Overtightening can

damagescrews, greatlyreducing their holdingpower.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

Installation to Concrete Wall

concrete

surface

Drill hole(s) and insert anchor(s) (W)

mounting

plate

Place plate over anchor(s) (W) and secure with screw(s)(O)

Tighten all fasteners

CUTAWAYVIEW

INCORRECT CORRECT

mounting

plate

plaster/

drywall

concrete mounting

plate concrete

plaster/

drywall

6 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06

Snap four cable management clips(R)into top or bottom of arm assembly(C)as shown.Cable ties (S) are used

withclips for cordmanagement.

Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables.

3-1

DETAIL 3

Note: There are five mounting positions. The

center position is shown (right). Slidewasher (J)

over wall support arm axle (D). Next, insert plastic

cap (N) into axle. Then, insert holding pin (M) into

axle. See detail 1.

Note: Fit of axle (D) into wall plate (A) and arm

assembly (C) will be tight. Gently tap into place

with a hammer if necessary.

2-1

Insert socket cap screw (K) into hole at bottom of

wall support arm axle (D) as shown in detail 3.

Tightenscrew using 9/64"allen wrench (Q).

Place arm assembly (C) with washer (J) into wall

plate (A). Insert axle assembly shown in detail 1

throughwall plate (A),armassembly (C),and

washer (J). Lock axle in place by aligning holding

pin (M) with notches shown in detail 2.

2-2

DETAIL 1

NOTCH

DETAIL 2

• If you are uncertain that product is properly installed, call customer care.

WARNING

7 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06

GENERIC

ADAPTERBRACKET

Insert and tape carriage bolt (I) into top hole of pitch-roll assembly (B).Attach tilt-roll assembly to adapter

bracket with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).

Note: Adapter bracket (not UL evaluated, sold separately) will vary in size and style.

Note: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceeding

with step 5. If your adapter bracket has an aluminum race attached to it, remove before proceeding and discard race. It is

not used with this product.

• Donotovertightenscrews!Overtightening mayhinder

rolloption.

CAUTION

Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm

assembly(C).

4-1 Insertone finishing cap (L) intoeach unused hole of wallplate (A).

SWIVELBOX

8 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06

Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed

thread.

.25"

• Use an assistant or mechanical lifting equipment to safely lift and position the plasmaTV.

WARNING

• After tilt is adjusted, all fasteners must be tightened.

Failure to do so will result in damage to the mount.

CAUTION

6-1

6-2

fig 6.1 fig 6.2

SWIVELBOX

Hook tilt-roll assembly (B) onto M10 screws (F).

Insert carriage bolt (I) into slot of swivel box as

shown in figure 6.1. Install nylon washer (G) and tilt

adjustmentknob (H).

Install remaining two M10 screws (F) as shown in

figure6.2. HANDTIGHTEN all fourM10 screwsto

allowfor tiltadjustment. Remove tapefrom carriage

bolt (I). For tilt adjustment, push back on the top of

plasma to relieve pressure on knob.Adjust tilt to

desired position and tighten tilt adjustment knob (H),

then securely tighten all four M10 screws (F) using 6

mmallen wrench (U).

SWIVELBOX

9 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06

FOR PLAV 60 ONLY:

77-1

ARTICULATINGARM

PLASMA

Depending on the specific size & weight of the plasma,

articulatingswing arm maybe angled atdifferent

positions, causing plasma to appear to lean sideways

atdifferent articulating positions.Tilt-roll assembly (B)

allows plasma to be manually adjusted, so plasma can

be horizontal at all positions.To adjust, gently rotate

plasma by hand to desired position.

SOCKET

SCREW

Position of screen may be adjusted vertically up to

.79" in each direction by doing the following:

• To lower screen, turn socket screw shown in figure

8.1 clockwise with 10 mm allen wrench (V).

• Toraisescreen, turn socket screwshown in figure

8.1 counterclockwise with 10 mm allen wrench (V).

fig 8.1

If it is too difficult to adjust roll of plasma, loosen

screws shown in figure 7.1 using a phillips screw-

driver.

IMPORTANT! Do notloosenor tighten screws

morethan 1/8 turn.

ROLL

ADJUSTMENT

SCREWS

fig 7.1

Peerlessis aregistered trademarkof PeerlessIndustries, Inc.

Allother brand andproduct namesaretrademarks orregistered trademarks oftheir respectiveowners.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PEERLESS Support TV

PEERLESS

PEERLESS ACC324 Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PF640 and assembly Manuel utilisateur

PEERLESS

PEERLESS HAVE1 FPZ-655 Manuel utilisateur

PEERLESS

PEERLESS PARAMOUNT PT640 and assembly Mode d’emploi

PEERLESS

PEERLESS HP450-GB Mode d’emploi

PEERLESS

PEERLESS DS-VL-H024 Mode d’emploi

PEERLESS

PEERLESS SUF640P and assembly Mode d’emploi

PEERLESS

PEERLESS HX632-LG-RJP Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PP740 Mode d’emploi

PEERLESS

PEERLESS CMJ 470 Mode d’emploi

PEERLESS

PEERLESS Smartmount D-FPT-220 Mode d’emploi

PEERLESS

PEERLESS SlimLine SLWS210/BK Manuel utilisateur

PEERLESS

PEERLESS WSP 320 Manuel utilisateur

PEERLESS

PEERLESS PARAMOUNT PT630 and assembly Mode d’emploi

PEERLESS

PEERLESS Smartmount ST630P and assembly Mode d’emploi

PEERLESS

PEERLESS DS416 Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PT660 Mode d’emploi

PEERLESS

PEERLESS Smartmount ST650 and assembly Mode d’emploi

PEERLESS

PEERLESS PLP PION50 Mode d’emploi

PEERLESS

PEERLESS SUF660P and assembly Mode d’emploi

PEERLESS

PEERLESS ST 632P Mode d’emploi

PEERLESS

PEERLESS Smartmount ST630P and assembly Mode d’emploi

PEERLESS

PEERLESS ACC 908 Mode d’emploi

PEERLESS

PEERLESS Smartmount ST632 Manuel utilisateur

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur

Marquant

Marquant 929-083 Mode d'emploi