PEERLESS PARAMOUNT PRTLU Manuel utilisateur

ISSUED: 11-03-09 SHEET #: 202-9395-1

Paramount™ Universal Tilt Wall Mount

for 37" - 60" Flat Panel Screens

Max UL Load Capacity: 200 lb (90 kg)

Model: PRTLU

Installation Guide

USC

This product was designed to be installed on wood stud walls and solid concrete (2000 psi

density minimum) or cinder block walls. Before installing make sure the supporting surface will

support the combined load of the equipment and hardware. Screws must be tightly secured. Do

not overtighten screws or damage can occur or product may fail. Never exceed the Maximum UL

Load Capacity. This product is intended for indoor use only. Use of this product outdoors could

lead to product failure or personal injury. For support please call customer care at 1-800-865-2112.

WARNING

2 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1

A(1)

S(4)

M4 x 12 mm

D(4)

E(4)

F(4)

M4 x 25 mm

G(4)

M5 x 12 mm

H(4)

M5 x 25 mm

I(4)

M6 x 12 mm

J(4)

M6 x 20 mm K(4)

M6 x 25 mm

L(4)

M6 x 30 mm

M(6)

M8 x 16 mm N(4)

M8 x 25 mm

O(4)

M8 x 40 mm

P(4)

ID .22" (5.6 mm)

Q(4)

ID .34" (8.7 mm) R(6)

B(1)C(1)

Tools Needed for Assembly

• studnder("edgetoedge"stud

 nderisrecommended)

•phillips screwdriver

•drill

• 5/32"(4mm)bitforwoodstudwall

• 5/16"(8mm)bitforconcreteand

cinder block

• level

• hammer (optional)

3 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1

Installation to Double Wood Stud Wall

Use wall plate (A) as a template, make sure it is level, and mark four mounting holes along the center

linesofthewoodstuds.Drillfour5/32"(4mm)dia.holes2.5"(64mm)deep.Levelwallplate(A) and

attach to wall with four wood screws (D)intostudcenter.Useofanedgetoedgestudnderishighly

recommended.Tightenscrewsrmly,butdonotovertighten.

Do not over tighten screws, or

damage may occur.

TOP CUTAWAY VIEW

Wood screws must

center in stud.

STUD

WARNING WARNING

4 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1

Installing to Solid Concrete or Cinder Block

Level wall plate (A)anduseasatemplatetomarkfourmountingholes.Drillfour5/16"(8mm)dia.

holes to a minimum depth of 2.5" (64 mm). Insert four anchors (E) into holes and secure wall plate (A)

with four screws (D).Tightenscrewsrmly,butdonotovertighten.

SOLID CONCRETE

CINDER BLOCK

5 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1

concrete

Place plate (A) over anchors (E). Secure with screws (D). Tighten screws.

Drill holes and insert anchors (E).

• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimum

of1-3/8"(35mm)ofactualconcretethicknessintheholetobeusedfortheconcrete

anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, gener-

ally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90

specications.Itissuggestedthatastandardelectricdrillonslowsettingisusedtodrillthe

hole instead of a hammer drill to avoid breaking out the back of the hole when entering a

void or cavity.

• Alwaysattachconcreteanchorsdirectly to load-bearing concrete.

WARNING

CUTAWAY VIEW

INCORRECT

CORRECT

plaster/

drywall

concrete

plaster/

drywall

wall plate

CORRECT

WARNING

concrete

6 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1

Topreventscratchingthescreen,setaclothonaat,levelsurfacethatwillsupportthe

weight of the screen. Place screen face side down. Refer to screen manufacturers instruc-

tions or customer service, for removing any knobs, base, cover, or screw(s) on the back of

the screen to prepare mounting. These need to be removed to allow the adapter brackets to

beattached.Selectthesmall,medium,largeorextralargescrewsfromthebafedfastener

packthenattachtiltbracketstoscreenfollowinggure2.1or2.2.

NOTE: Be sure to attach tilt brackets with handles facing outward as shown below.

NOTE: Top and bottom mounting holes must be used for attaching brackets. Middle holes

should also be used where the fasteners and screens allow. Verify that all holes are properly

aligned, and then tighten screws using a phillips screwdriver.

CENTER BRACKETS VERTICALLY

ON BACK OF SCREEN

HANDLES FACE OUT

Notes:

• Thenumberoffastenersused

will vary, depending upon the

type of screen.

• Multi-washersandspacersmay

not be used, depending upon

the type of screen.

• Usethecorrespondingholein

the multi-washer that matches

your screw size.

MEDIUM HOLE

FOR M5 SCREWS

SMALL HOLE

FOR M4 SCREWS

LARGE HOLE

FOR M6 SCREWS

MULTI-WASHER

NOTE: "X" dimensions should be equal.

Installing Adapter Brackets

7 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1

g.2.1

SCREW

MULTI-WASHER

ADAPTER

BRACKET

(Bor C)

SCREEN

For Bump-out or Recessed Back Screen

2-2 Refer to screen compatibility chart to determine the proper fastener to use. Visit

www.peerlessmounts.com/2for a full screen compatibility chart for this mount.

Begin with longer length screw, hand thread through multi-washer, adapter bracket and

spacer in that order into screen as shown below. Screw must make at least three full turns

intothemountingholeandtsnugintoplace.Donotovertighten.Ifscrewcannotmake

threefullturnsintothescreen,selectalongerlengthscrewfromthebafedfastenerpack.

Repeat for remaining mounting holes, level brackets and tighten screws.

2-1 Refer to screen compatibility chart to determine the proper fastener to use. Visit

www.peerlessmounts.com/2for a full screen compatibility chart for this mount.

Begin with the shortest length screw, hand thread through multi-washer and adapter bracket

into screen as shown below. Screw must make at least three full turns into the mounting hole

andtsnugintoplace.Donotovertighten.Ifscrewcannotmakethreefullturnsintothe

screen,selectalongerlengthscrewfromthebafedfastenerpack.Repeatforremaining

mounting holes, level brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

For Flat Back Screen

If you have any questions, please call Peerless customer care at 1-800-865-2112.

• Ifscrewsdon'tgetthreecompleteturnsinthescreeninsertsorifscrewsbottomoutand

bracket is still not tightly secured, damage may occur to screen or product may fail.

WARNING

SCREW

SCREEN

SPACER

MULTI-WASHER

ADAPTER

BRACKET

(Bor C)

g.2.2

8 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1

Mounting and Removing Flat Panel Screen

Tension Adjustment of Ratchet Handle: Adjust tension in tilt brackets (B & C) by rotating ratchet

handle. NOTE: If obstruction prevents ratchet handle from rotating, pull handle out while turning will

allow handle to reposition without tightening. Release and turn handle to tighten or loosen.

Mounting Screen: Ratchet handle must be in the up or down position or interference will occur while

hooking tilt brackets to wall plate (A). Slowly hook tilt brackets (B & C) onto wall plate (A) and swing

screendownasshowning.3.1.Tiltbrackethooksmustfullyengagewallplateasshownindetail1.

Alwaysuseanassistanttosafelyliftandpositiontheatpanelscreen.Usingaphillipsscrewdriver,turn

safety screws on tilt brackets (B & C) clockwise till screw tip securely contacts wall plate as shown in cross

section.

Removing Screen: To remove screen from mount, loosen safety screws, swing screen away from

mount, and lift screen off of mount.

Failure to lock brackets (B &C) with safety

screws can cause sceen to come off mount

if hit accidentally.

WARNING

g3.1

RATCHET

HANDLE

SAFETY

SCREW

DETAIL 1

CROSS SECTION

B & C

9 of 32 ISSUED: 11-03-09 SHEET #: 202-9395-1

g.3.2

Screen Adjustment: Screen can be adjusted horizontally by loosening safety screws on tilt

brackets (B & C)threefullturnswithaphillipsscrewdriver.Adjustscreenasshowningure

3.2. Tighten safety screws on tilt brackets till screw tip securely contacts wall plate as shown

in cross section.

Adjusting the Tilt Angle of the Flat Panel Screen

For preset tilt angles use Increlok™ and for custom tilt angle use ratchet handle.

INCRELOK™:The screen can be locked into a pre-set tilt position of -5°, 0°, 5°, 10°or 15°. Use

locatorholetondtiltpositionholeandtiltscreentoalignholes.TightenIncreLok™tiltlocking

screws on both tilt brackets to lock tilt as shown in detail 2.

Ratchet Handle: Loosen ratchet handle (refer to step 3 for tension adjustment of handle). Push or

pullfromtoporbottomofscreentoadjusttiltasshowningure4.1.Thetiltcanbeadjustedtoa

maximum of 15° forward or 5° backward.

DETAIL 2

g4.1

IncreLok™ TILT

LOCKING SCREW

LOCATOR

HOLE

RATCHET

HANDLE

TILT

POSITION

HOLES

3-1

Table des matières

Langues :

Autres manuels PEERLESS Support TV

PEERLESS

PEERLESS ST 632P Mode d’emploi

PEERLESS

PEERLESS Smartmount ST650 and assembly Mode d’emploi

PEERLESS

PEERLESS WSP816 Mode d’emploi

PEERLESS

PEERLESS SUF650P and assembly Mode d’emploi

PEERLESS

PEERLESS SUT645P Mode d’emploi

PEERLESS

PEERLESS WSP824 Mode d’emploi

PEERLESS

PEERLESS IM740P Mode d’emploi

PEERLESS

PEERLESS Smartmount D-FPT-220 Mode d’emploi

PEERLESS

PEERLESS HAVE1 FPZ-655 Manuel utilisateur

PEERLESS

PEERLESS Designer Series Mode d’emploi

PEERLESS

PEERLESS Smartmount ST630P and assembly Mode d’emploi

PEERLESS

PEERLESS LWS210/BK Mode d’emploi

PEERLESS

PEERLESS Smartmount ST670 Manuel utilisateur

PEERLESS

PEERLESS PLA 50-S Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PT660 Manuel utilisateur

PEERLESS

PEERLESS SS550P and assembly Mode d’emploi

PEERLESS

PEERLESS Jumbo 2000 JM 2630 Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PRFLU Manuel utilisateur

PEERLESS

PEERLESS PARAMOUNT PF640 and assembly Mode d’emploi

PEERLESS

PEERLESS SMARTMOUNT SF 635P Mode d’emploi

PEERLESS

PEERLESS SUAC9000 and assembly Mode d’emploi

PEERLESS

PEERLESS Paramount PP730 and assembly Mode d’emploi

PEERLESS

PEERLESS SmartMount SF680 and assembly Mode d’emploi

PEERLESS

PEERLESS ACC324 Mode d’emploi

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur

Marquant

Marquant 929-083 Mode d'emploi