PEERLESS DSX200 Mode d’emploi
1 of 5 ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
Installation and Assembly:
Shelf Bracket for Media Device
Secure two adjustment brackets (D) to shelf (A) using four 1/4-20 x 1/2 round phillips screws (G).
Model: DSX200
C D
A
E F G
High Shelf Position Low Shelf Position
G
G
AA
D
D
1
B
H
Description Qty. Part #
A
shelf 1 124-1941
Bright vertical support 1 124-1944
Cleft vertical support 1 124-1943
Dadjustment bracket 2 124-1945
EM5 x 16 phillips screw 8 520-1189
FM5 x 25 mm phillips screw 2 520-9543
G1/4-20 x 1/2 round phillips screw 4 510-9108
Hsafety belt 1 170-8039-1
Parts List
USE BACK MOUNTING HOLES USE BACK MOUNTING HOLES
2 of 5 ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
Attaching to Wall Plate
Hook right and left vertical supports (Band C) onto wall plate (not supplied) and secure using two
M5 x 25 mm phillips screws (F).
NOTE: Don’t fully tighten M5 x 25 mm phillips screws (F) until after Step 3
2
F
C
B
Wall Plate
(Not supplied)
High Shelf Position Low Shelf Position
E
C
C
Wall Plate
(Not supplied)
Wall Plate
(Not supplied)
B
B
Secure adjustment brackets (D) to right and left vertical supports (Band C) using eight M5 x 16 mm phillips screws (E).
Position right and left vertical supports (Band C) in desired location then tighten M5 x 25 mm phillips screws (F).
3
D
D
E
F
F
3 of 5 ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
Attaching Safety Belt
Select slot in tray as shown in g 4.1.
Remove backing and attach one clear strip through slot and around edge of tray as shown in g. 4.2.
Repeat for other slot on other side of tray.
NOTE: This material prevents fraying or cutting of the belt.
4
Fig. 4.1 Fig. 4.2
SLOT
FRONT LIP CLEAR STRIPS
Take one belt and hold it so that the tri-bar belt clip is facing as illustrated. Feed belt up through the slot you have chosen.
Remember, belt only goes through outside slot. Now feed belt through belt clip as shown.
Repeat on other side of tray using other belt.
123
5
AH
Continue by sliding on one belt guide and tri-bar clip on each side of the buckle. Refer to drawing below.
6
TOP
BOTTOM NOTE: Teeth face down
TRI-BAR BELT CLIP
4 of 5 ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
BELT GUIDE BELT GUIDE
Pull end of safety belt (H) out of bottom buckle slot and back down through top buckle slot.
NOTE: Do not tighten safety belt (H).
45
Bottom buckle slot Top buckle slot
Tighten safety belt (H) by pulling on loose end of safety belt.
H
6
NOTE: To attach screen to wall plate, spacers may be needed. Refer to wall mount instructions for use of spacers.
5 of 5 ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
Make sure that attachment brackets (not included) are at
desired tilt before installing to wall plate (not included).
Measure display hole pattern before securing display to
wall plate (not included).
If display mounting pattern is larger than distance between vertical
supports of shelf mount brackets, position attachment brackets on
outside with ratchet handles facing outward as shown in Fig 7.1.
If display mounting holes are smaller than distance between vertical
supports of shelf mount brackets, position attachment brackets on
inside with ratchet handles facing inward as shown in Fig 7.2.
NOTE: Shelf will be offset to the right or left in this orientation.
If display mounting holes are equal to distance between vertical
supports of shelf mount brackets, position attachment brackets on
right or left side of shelf mount brackets with ratchet handles facing
outward as shown in Fig 7.3.
NOTE: Vertical brackets can be mounted on right or left side of shelf
as shown in light gray.
Fig. 7.1
Fig. 7.2
Fig. 7.3
7
Vertical brackets Outside
Vertical brackets inside
Vertical brackets inside and Outside
Large Mounting Hole Pattern
18.65"
18.65"
ATTACHMENT BRACKETS
VERTICAL BRACKETS
ATTACHMENT BRACKETS
VERTICAL BRACKETS
ATTACHMENT BRACKETS
VERTICAL BRACKETS
RATCHET HANDLE
RATCHET HANDLE
RATCHET HANDLE
Small Mounting Hole Pattern
Same Mounting Hole Pattern
© 2010, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or
registered trademarks of their respective owners.
Table des matières
Autres manuels PEERLESS Support TV
PEERLESS
PEERLESS SmartMount SF680 and assembly Mode d’emploi
PEERLESS
PEERLESS PARAMOUNT PT632 and assembly Mode d’emploi
PEERLESS
PEERLESS PLA 60 and assembly Mode d’emploi
PEERLESS
PEERLESS HLG452-002 Mode d’emploi
PEERLESS
PEERLESS ACC 908 Mode d’emploi
PEERLESS
PEERLESS SS550P and assembly Mode d’emploi
PEERLESS
PEERLESS SUA746PU Mode d’emploi
PEERLESS
PEERLESS HP450 Manuel utilisateur
PEERLESS
PEERLESS PARAMOUNT PF630 and assembly Mode d’emploi
PEERLESS
PEERLESS SUT645P Mode d’emploi
PEERLESS
PEERLESS WSP816 Mode d’emploi
PEERLESS
PEERLESS Smartmount ST632 Manuel utilisateur
PEERLESS
PEERLESS HP450-GB Mode d’emploi
PEERLESS
PEERLESS Smartmount ST640 Manuel utilisateur
PEERLESS
PEERLESS PM 13 and assembly Mode d’emploi
PEERLESS
PEERLESS SmartMount SF670 and assembly Mode d’emploi
PEERLESS
PEERLESS MIS374A Mode d’emploi
PEERLESS
PEERLESS Smartmount ST632P Mode d’emploi
PEERLESS
PEERLESS PARAMOUNT PT640 and assembly Mode d’emploi
PEERLESS
PEERLESS DS508 and assembly Mode d’emploi
