PEERLESS HL4UN-002 Mode d’emploi

1 of 2 ISSUED: 06-03-11 SHEET #:120-9110-1

Insert two 1/4-20 x 1-3/4" carriage bolts (A)

into bottom of display base as shown in detail 1.

Model: HL4UN-002, HL4UN-002-Q10

Installation and Assembly:

Lock Down Hardware for Display Base Stands

BOTTOM OF BASE

FRONT

A B

DETAIL 1

MEASURE

DISTANCE

Measure distance between center lines of cut outs in

bottom of display base. Use measurement to mark

location of holes at point 1 and point 2, on table.

Drill two holes using a 9/32'' drill bit.

POINT 1

POINT 2

• drill

• 9/32" drill bit

• 5/8" open box wrench

E F G

HTOOLS NEEDED

HL4UN-002 HL4UN-002-Q10

Description Qty. Part # Qty. Part #

1/4-20 x 1 3/4" carriage bolt 2 520-1017 20 520-1017

BM4 x 16 mm phillips trilobe screw 2 520-2621 20 520-2621

CM4 x 16 mm socket pin screw 2 520-1087 20 520-1087

D1/4-20 sloped nut 3 530-0035 23 530-0035

EM4 x 12 mm socket pin screw 2520-1079 20 520-1079

F#8 flat washer 2540-1001 20 540-1001

Gplastic cap 2590-1294 20 590-1294

H4 mm allen wrench 1 560-9646 3 560-9646

Parts List

NOTE: Display and base may appear

different than illustrated

2 of 2 ISSUED: 06-03-11 SHEET #:120-9110-1

Hand tighten slope nut (D) through 1/4-20 x 1-3/4" carriage bolt (A) until snug against bottom of desktop surface.

Thread another slope nut (D) upside-down, about two turns from rst slope nut (D). Insert an open box wrench

between both slope nuts (D) and tighten. NOTE: Avoid jamming both slope nuts (D) together, doing so may make

it difcult to remove slope nut used for tightening rst slope nut (D) as shown in gure 3.1. After slope nut is secure

remove bottom slope nut as shown in gure 3.2. Repeat with remaining 1/4-20 x 1 3/4" carriage bolt (A).

Fasten two plastic caps (G).

TIGHTENING

SLOPE NUT

BOTTOM OF DESKTOP

FIGURE 3.1 FIGURE 3.2

NOTE: Do not overtighten slope nut (D)

plate may distort

FRONT

Thread two M4 x 16 phillips pan trilobe screws (B) to bottom display attachment holes as shown in g. 4.1.

Remove the two M4 x 16 phillips pan trilobe screws (B) and attach display screen to display base using two M4 x

16 mm socket pin screws (I) or M4 x 12 mm socket pin screws (E) with #8 at washers (F), as shown in gure 4.2.

Tighten with 4 mm security allen wrench (H). Use TV supplied screws for remaining holes.

g 4.1 g 4.2

DISPLAY SCREEN DISPLAY SCREEN

DISPLAY BASE

NOTE: Display and base may appear

different than illustrated

NOTE: Screws are installed using bottom

two display mounting locations.

Installation of Security Screws for Base/Screen Assembly

C or E

• If screws don’t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

All other brand and product names are trademarks or registered trademarks of their respective owners.

Ce manuel convient aux modèles suivants

Autres manuels PEERLESS Support et étagère

PEERLESS

PEERLESS DS415 Mode d’emploi

PEERLESS

PEERLESS Paramount PSP2 Mode d’emploi

PEERLESS

PEERLESS WSP820 Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PA730 Mode d’emploi

PEERLESS

PEERLESS SF 24D Mode d’emploi

PEERLESS

PEERLESS Solid-Point PLB 1 Mode d’emploi

PEERLESS

PEERLESS HCACC503 Manuel utilisateur

PEERLESS

PEERLESS SOLID POINT PLCM 1 Mode d’emploi

PEERLESS

PEERLESS SmartMount D-FPF-320 Mode d’emploi

PEERLESS

PEERLESS DS246 Mode d’emploi

PEERLESS

PEERLESS PLCM 3 Mode d’emploi

PEERLESS

PEERLESS SAL730P Mode d’emploi

PEERLESS

PEERLESS FPZ-600 Mode d’emploi

PEERLESS

PEERLESS RTPLA 50 Mode d’emploi

PEERLESS

PEERLESS DS495 Mode d’emploi

PEERLESS

PEERLESS SmartMount SP850-UNL Mode d’emploi

PEERLESS

PEERLESS Smartmount SWS310/BK Mode d’emploi

PEERLESS

PEERLESS AEC0609 Mode d’emploi

PEERLESS

PEERLESS IBA1 Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PP740 Manuel utilisateur

PEERLESS

PEERLESS ST 640 Mode d’emploi

PEERLESS

PEERLESS LCT-202 Mode d’emploi

PEERLESS

PEERLESS LCC 18 Mode d’emploi

PEERLESS

PEERLESS Perfect Mount PMF2X2 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur