LINSHANG LS191 Manuel utilisateur

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 1 of 16

Gloss Meter

User Manual V3.1

Please read the manual carefully before you use.

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 2 of 16

Instruction for use

Thank you for choosing and using LS191/LS192 gloss meter. In order

to better use the product, please read the manual carefully before you

use.

The "gloss meter" mentioned herein refers to specular gloss

meter. It is also called as "gloss gauge".

The "standard" mentioned herein refers to the working

calibration standard plate which forms a complete set with the

meter and is used for meter calibration.

The working temperature of the meter should fall between

10℃- 40℃, and the relative humidity should be less than 85%,

without congealed hoarfrost.

The storage temperature of the meter should fall between

-10℃- 60℃. The meter should be kept away from heat sources

and corrosive agents and stored in a dry place.

The meter should be used without strong electromagnetic

interference.

The meter provides one-year warranty. As for meter's failure

resulted from normal use during the warranty, the company is

responsible to maintain such failure without any charge. As for

failure resulted from improper use or disassembly at random, the

users will be liable for it by their own.

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 3 of 16

Table of Contents

I: About the meter.................................................................................4

II: Structure...........................................................................................6

III: Technical parameters ......................................................................6

IV: Operation ........................................................................................7

1．Powering on ........................................................................................................................7

2．Auto Calibration..................................................................................................................9

3．Measurement.....................................................................................................................12

4．Powering off......................................................................................................................13

V: Maintenance ..................................................................................14

VI: Factory list ....................................................................................15

VII: Service.........................................................................................16

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 4 of 16

I: About the meter

LS191/LS192 accords with the following standards:

ISO2813, ISO7668, ASTM D523, ASTM D2457, DIN 67530,

GB/T9754, GB/T13891, GB/T7706, GB/T8807

All indexes of the meter meet the requirements of JJG 696-2002

Verification Regulation of 《Specular Gloss Meters and Gloss

Plates 》for class one working meters.

Table 1 Verification performance of the gloss meter

LS191/LS192 features:

To provide real time measurement and put-and-measure

services without pressing buttons. It displays the measurement

data on a real time basis

Equipped with intelligent statistics function. The number of

measurements, the maximum value, the minimum value, the

average value and the standard deviation are directly shown in

the display interface

To have environmental temperature compensation function

and provide the ability of numerical stability.

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 5 of 16

Unique is the intelligent auto diagnosis of the gloss meter

which guarantees long-term stable calibration

To support USB transmission and has PC operating software.

It can be on-line operated with the computer to complete the

test report

Aviation aluminum housing and Calibration Holder, with

super good quality; small design, and being easy to carry

Built in rechargeable lithium battery, with Ultra low power

consumption

LS191/LS192 is widely used for:

Gloss measurement of materials and products in the fields of

paint coatings, decorative materials, building materials, plastic

materials, ceramic products, stone products, wood products,

leather products, film-coated paper towel, printing ink, car

maintenance, molding tool, metal coating, etc.

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 6 of 16

II: Structure

III: Technical parameters

Technical

parameters

Unit LS191 gloss meter LS192 gloss meter

Angle Degree 60 60

Measuring Area mm 9*15 9*15

Measurement

range GU 0-200 0-1000

Resolution GU 0.1 0.1

Repeatability GU 0-100: ±0.2

100-200: ±0.2%

0-100: ±0.2

100-1000: ±0.2%

Reproducibility GU 0-100: ±0.5

100-200: ±0.5%

0-100: ±0.5

100-1000: ±0.5%

Zero error GU 0.1 0.1

Error of

indication GU 0-100: ±1.5

100-200: ±1.5%

0-100: ±1.5

100-1000: ±1.5%

Working

temperature ℃10℃～40℃10℃～40℃

Storage

temperature ℃-10℃～60℃-10℃～60℃

Relative humidity Less than 85％, no dew Less than 85％, no dew

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 7 of 16

Power supply Lithium rechargeable

battery

Lithium rechargeable

battery

Meter size mm 104(L) * 35(W) * 60(H) 104(L) * 35(W) * 60(H)

Meter weight g 332 332

IV: Operation

1．Powering on

Under the status of powering off, press the button of "Power" to power

on the meter. Normally, the meter will successively enter into start

interface, warm-up interface, autodiagnosis interface, auto calibration

interface and measurement interface. The whole process will last

about 10 seconds. After entering into the measurement interface, the

users can make the measurement.

Start interface

Warm-up interface, warm-up process will last 5 seconds

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 8 of 16

Autodiagnosis interface. The meter must be power on in the

“Calibration Holder”, running autodiagnosis to timely find out the

system errors, improper operation and environmental changes.

Once the autodiagnosis result is normal, the system will display

"OK", with the meter entering into the auto calibration interface.

Autodiagnosis function to check whether the “calibration standard”

is clean. If the standard value of the “calibration standard” falls out

of qualified range, the meter will display “Please clean standard”.

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 9 of 16

Then, the followings should be carried out:

1.If the standard is not clean, please clean the standard with

special lens cloth, before placing the meter into the Calibration

Holder.

2.If the meter is not clung to the Calibration Holder, please re-place

into the Calibration Holder.

3.If a great change happens to the environmental temperature,

restart the meter for measurement, after confirming that the meter

temperature tends to be equal to the environmental temperature

and that lens in the measuring port and the standard on the

Calibration Holder are free from congealed hoarfrost.

After ruling out the above problems, place again the meter into the

Calibration Holder and the meter will run again the autodiagnosis. If

the troubles are removed, the meter will display “OK” and enter into

the auto calibration mode .

If the meter display “Please clean standard”. Also can enter into the

auto calibration mode manually by short press “Power “key.

Shenzhen Linshang Technology Co.,Ltd.

1-4-2019 Page 10 of 16

2．Auto Calibration

If the meter starts in the Calibration Holder, it will enter into

calibration mode after autodiagnosis .If the autodiagonosis process

is still unfinished,short press “Power” key and the meter will enter

into auto calibration mode.

Before the number reaches 0, short press "Power" Key and

the meter will run auto calibration. After calibration, it will enter

into measurement mode,and the measuring value is the same

as that shown by the label on the right side of the meter.

If the no key pressed before the number reaches 0, the

meter will directly enter into the measuring status without

calibration operation.

If the system displays “Please call service” after calibration,the

reasons may include:

1) The standard is not clean. Please clean the standard before

calibrating.

2) The meter is not clung to the Calibration Holder. Please place

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LINSHANG Instrument de mesure

LINSHANG

LINSHANG LS236 Manuel utilisateur

LINSHANG

LINSHANG LS212 Manuel utilisateur

LINSHANG

LINSHANG LS110A Manuel technique

LINSHANG

LINSHANG LS160A Manuel utilisateur

LINSHANG

LINSHANG LS108H Manuel utilisateur

LINSHANG

LINSHANG LS171 Manuel utilisateur

LINSHANG

LINSHANG LS137 Manuel utilisateur

LINSHANG

LINSHANG LS193 Manuel utilisateur

LINSHANG

LINSHANG LS125 Manuel utilisateur

LINSHANG

LINSHANG LS126C Manuel utilisateur

LINSHANG

LINSHANG LS192 Manuel utilisateur

LINSHANG

LINSHANG LS120 Manuel utilisateur

LINSHANG

LINSHANG LS163 Manuel utilisateur

LINSHANG

LINSHANG LS232 Manuel utilisateur

LINSHANG

LINSHANG LS108 Manuel utilisateur

LINSHANG

LINSHANG LS301 Manuel utilisateur

LINSHANG

LINSHANG LS213 Manuel utilisateur

LINSHANG

LINSHANG LS133 Manuel utilisateur

LINSHANG

LINSHANG LS123 Manuel utilisateur

LINSHANG

LINSHANG LS162A Manuel utilisateur

LINSHANG

LINSHANG LS195 Manuel utilisateur

LINSHANG

LINSHANG LS130 Manuel utilisateur

LINSHANG

LINSHANG LS201 Manuel utilisateur

LINSHANG

LINSHANG LS126A Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur