LINSHANG LS230 Manuel utilisateur

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 1 of 8

LS230

Coating Thickness Gauge

User Manual V2.0

Please read this manual carefully before using and reserve it for reference.

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 2 of 8

I. Product introduction

Coating thickness gauge is used for measuring the thickness of

automobile paint. The automotive body shell consist of metal materials

such as iron and aluminum and other non-metallic materials such as

carbon fiber and plastic. This coating thickness gauge can measure the

thickness of car paint on iron and aluminum materials. Moreover, it can

identify not only non-metal car bodies, but also the ferrous putty layer as

well as the galvanized iron. This coating thickness gauge uses low

temperature resistant OLED as the display interface to ensure that the

display is still normal in the low temperature environment of -40℃.

Standards for the product:

 DIN EN ISO 2808 Paints and Varnishes-Determination of Film

Thickness

 JJG-818-2005 Verification Regulation of Magnetic and Eddy

Current Measuring Instrument for Coating Thickness

 GB/T 4956-2003 Non-magnetic Coatings on Magnetic Substrates-Measurement of Coating

Thickness-Magnetic Method

 GB/T 4957-2003 Non-conductive Coatings on Non-magnetic Basis Metals-Measurement of

Coating Thickness-Eddy Current

II. Technical parameters

Probe tip Ruby

Measuring principle Fe: Hall Effect / NFe: Eddy Current

Probe type Built-in integrated probe

Measuring range 0.0-2000μm

Resolution

0.1μm:(0μm - 99.9μm)

1μm:(100μm - 999μm)

0.01mm:(1.00mm - 2.00mm)

Accuracy ≤±(3% reading+2μm)

Unit μm / mil

Measuring interval 0.5s

Minimum measuring area Ø = 25mm

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 3 of 8

Minimum curvature Convex:5mm / Concave:25mm

Minimum substrate thickness Fe:0.2mm / NFe:0.05mm

Display 128 * 64 dot matrix OLED

Power supply 2pcs of 1.5V AAA alkaline battery

Range of operation temperature -40℃ - 50℃

Storage temperature range -50℃ - 60℃

Gauge size 101*62*28 mm

Weight(with battery) 79g

III. Product advantages

1. No calibration, just zero adjustment.

2. One hand operation, only one button.

3. Fast measurement, 0.5s measuring interval.

4. Use OLED display, the gauge displays normally in -40℃ low temperature environment.

5. Wear-proof ruby probe tip for long-term use.

6. The device can identify the ferrous putty as well as the galvanized iron substrate.

7. The gauge automatically identify the substrate and switch measurement mode rapidly.

8. "Fe", "NFe", "Fe/NFe" three measurement modes can be set.

9. Measuring non-magnetic coatings on steel or iron and measure non-conductive coatings on non-

magnetic metal substrates in one gauge.

10. Thanks to the use of the most-advanced digital probe technology, these sensors are unsusceptible to

interference and provide an excellent measuring accuracy. Even variations in temperature will not

affect measurement and readings remain stable to ensure a very good reproducibility over the

complete measuring range.

IV. Operation

1. Power on/off

Power on:

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 4 of 8

Short press the power button to turn on the gauge. Display the version number and serial number, then

the recorded data of last measurement are displayed after the gauge is turned on.

Power off:

Long press the button to shut down the gauge, or the gauge will automatically shut down in 3 minutes

without any operation.

2. Device setting

In the off state, long press the button for 3 s to enter the setting interface. After entering the setting interface,

if there is no operation for more than 20 s, the instrument will automatically Shortly press the button can

select the settings; Long press the button for 3 s and less than 5 s to confirm the settings; Long press the

button for 5 s, the instrument exits the setting and shuts down and the setting is invalid.

Language settings

The instrument is available in Chinese, English, Russian, Turkish.

Setting method: In the main setting interface, short press power button to select "Language" option, long

press the button for 3 seconds to confirm the selection, short press the button again to select the desired

language, long press the button for 3 seconds to confirm the selection, and return to the main setting

interface.

Setting interface Language selection

Measurement modes selection

There are three measurement modes: Ferrous substrate measurement (Fe), Aluminum substrate

measurement (Al), and Auto identification (Fe/Al). Under normal circumstances, it is enough to use Fe/Al

auto identification mode. This mode features identification of the ferrous putty and galvanized iron

substrate. When the measurement substrate is settled, you can select Fe or Al as the fixed

measurement mode.

Setting method: In the main setting interface, select "mode" option by short pressing power button, and

long press the button for 3 seconds to confirm the selection. Shortly press the button to select the

measurement mode. And long press the button for 3s to confirm the selection and back to the main

setting interface.

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 5 of 8

Unit setting

The device can be set to the metric or imperial unit, and the factory default is metric.

Setting method: In the main setting interface, shortly press the button to select “Unit”. Long press the

button for 3s to confirm and then enter the unit selection interface. Shortly press the button to select your

unit and long press the button for 3s to confirm and back to the main setting interface.

Main setting interface Unit selection interface

Exit

In the main setting interface, short press power button to select "Exit", long press the button for 3

seconds to confirm and enter the measurement interface

3. Zero adjustment

A zero-adjustment is required when using the gauge for the first time, after inserting new batteries, working

with different materials or ambient temperature changes. Using iron-base and aluminum - base adjustment

plates respectively to carry out zero adjustment. We strictly recommend carrying out the reference check

on the uncoated original substrate, due to the difference of magnetic and conductive properties of the

material, some measurement deviation will be caused. If this is not possible, please use the zero reference

plates supplied by Linshang technology, there are Fe plate and NFe plate, please choose correctly

according to the measuring materials.

3.1 Measuring the plate or uncoated original substrate, a measured value will be displayed on the gauge,

please make sure the probe tip is placed perpendicularly and evenly on the surface.

3.2 Hold the probe still, long press the button for 3s, the gauge will display “zero reference place probe”

(as shown in below picture).

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 6 of 8

3.3 After hearing a buzzer sound, the gauge will display “Lift off probe at least 15 cm” (as shown in below

picture), release the button and lift the probe away from the plate (substrate) for at least 15 cm.

3.4 The zero adjustment completed when there is the buzzer sound again, and the LCD screen displays

0.0.

3.5 After the zero adjustment is completed, place the standard film on the plate (substrate), if the

measurement value is stable and deviation from standard value within ±3μm, the gauge can be used

normally.

Note: After the zero adjustment completed，when repeating measurement on the same spot, the

reading may not always be 0μm, since surface roughness, dirt, scratches etc. It might cause

variances. The operation of the gauge should be correct and proficient; otherwise, it will lead to

instability of the measured values.

4. Measurement

1) Use fingers to hold gauge where there is non-slip groove.

2) Press the gauge vertically on the surface of the object to be measured. Keep the gauge steady and

do not tilt or shake it. The result will be shown on the screen, and there will be a buzzer.

3) To continue measuring, lift the gauge away from the object. Repeat the operation of step 2).

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 7 of 8

4) When the device identifies the ferrous putty, the buzzer alerts for two times. And the interface of the

device will prompt: “Ferrous putty”. When the device identifies the galvanized iron, it will turn on the

green backlight. The substrate is displayed as “FeZn”.

5. Check measurement records

In measurement mode, short press the button to check historical data. The gauge stores 9 sets of data.

When more than 9 sets of data are stored, the earliest recorded value is automatically deleted, and No.1

is the last test data. Recorded data will not loss after powering off.

V. Attentions

1. The device must be zero adjusted respectively with the iron-base and aluminum-base zero adjustment

plates. Otherwise, there may be abnormal identifications of the ferrous putty and galvanized iron

substrate.

2. Do not slide the probe on the automotive surface, which will result in damage to the paint and the

gauge.

3. Please keep the automotive paint surface clean, the dust and dirt on the paint surface will affect the

measurement accuracy.

4. When the gauge displays low battery, the battery needs to be replaced.

VI. Packing list

No. Description Quantity Unit

1 Coating thickness gauge 1 Set

2 Fe zero-adjustment plate 1 pcs

3 NFe zero-adjustment plate 1 pcs

4 Standard film 1 pcs

5 User manual 1 pcs

6 Drawstring bag 1 pcs

7 Certificate / Warranty card 1 pcs

8 1.5V AAA alkaline battery 2 pcs

Shenzhen Linshang Technology Co., Ltd

7-29-2020 Page 8 of 8

VII. Service

1. The gauge has one-year warranty. If the gauge works abnormally, please send the whole gauge to

our company for maintenance.

2. Provide users with spare parts and lifelong maintenance services.

3. Provide the users with the gauge calibration service.

4. Free technical support for long term.

Manufacturer: Shenzhen Linshang Technology Co., Ltd.

Website: www.linshangtech.com

Service hotline: +86-755-86263411

Email: sales21@linshangtech.com

Table des matières

Autres manuels LINSHANG Instrument de mesure

LINSHANG

LINSHANG LS131 Manuel utilisateur

LINSHANG

LINSHANG LS220 Manuel utilisateur

LINSHANG

LINSHANG LS212 Manuel utilisateur

LINSHANG

LINSHANG LS220B Manuel utilisateur

LINSHANG

LINSHANG LS137 Manuel utilisateur

LINSHANG

LINSHANG LS110A Manuel technique

LINSHANG

LINSHANG LS125 Manuel utilisateur

LINSHANG

LINSHANG LS108A Manuel utilisateur

LINSHANG

LINSHANG LS108 Manuel utilisateur

LINSHANG

LINSHANG LS196 Manuel utilisateur

LINSHANG

LINSHANG LS171 Manuel utilisateur

LINSHANG

LINSHANG LS160A Manuel utilisateur

LINSHANG

LINSHANG LS110H Manuel technique

LINSHANG

LINSHANG LS136 Manuel utilisateur

LINSHANG

LINSHANG LS108A Manuel utilisateur

LINSHANG

LINSHANG LS252DL Manuel utilisateur

LINSHANG

LINSHANG LS132 Manuel utilisateur

LINSHANG

LINSHANG LS236 Manuel utilisateur

LINSHANG

LINSHANG LS301 Manuel utilisateur

LINSHANG

LINSHANG LS182 Manuel utilisateur

LINSHANG

LINSHANG LS200 Manuel utilisateur

LINSHANG

LINSHANG LS120 Manuel utilisateur

LINSHANG

LINSHANG LS123 Manuel utilisateur

LINSHANG

LINSHANG LS133 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur