Kramer TP-590Txr Manuel utilisateur

TP-590TXR Quick Start (P/N: 2900-300864QS REV 2)

P/N:

2900- 300864QS

Rev:

Scan for full manual

TP-590TXR Quick Start Guide

This guide helps you install and use your TP-590TXR for the first time.

Go to www.kramerav.com/downloads/TP-590TXR to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

TP-590TXR HDMI Line Transmitter

4 Rubber feet

1 Bracket set

1 Power supply (48V DC)

1 Quick start guide

Step 2: Get to know your TP-590TXR

Feature

Function

USB Connector

Connect to the USB host, (for example, a laptop).

POE STATUS LED

Lights green when power is supplied over the HDBT link.

LINK LED

Lights green when the HDBT link is valid.

IN LED

Lights green when an HDMI active signal device is connected.

ON LED

Lights green when the device receives power.

Feature

Function

HDMI IN Connector

Connect to the HDMI source.

IR 3.5mm Mini Jack Connector

Connect to an external infrared transmitter or sensor.

RS-232 3-pin Terminal Block

Connect to an RS-232 controller, (for example, a PC to control the projector).

AUDIO IN 3.5mm Mini Jack

Connect to the stereo, analog audio source.

HDBT OUT RJ-45 Connector

Connect to the HDBT IN RJ-45 connector on the HDBT receiver.

SETUP 4-way DIP-switch

Sets the device behavior (see Step 4).

CONTROL

RS-232 3-pin

Terminal Block

Connect to the serial controllerto control this device.

ETHERNET

RJ-45 Connector

Connect to the Ethernet controller to control this device or to a LAN to transfer network traffic.

RESET Switch

Press and hold for 5 seconds to reset the device to factory default settings.

Press and immediately release to power-cycle the device (Reset).

PROG Mini USB Connector

Connect to a PC to perform firmware upgrades.

48V DC Power Connector

Connect to the power supply.

Step 3: Install TP-590TXR

Install TP-590TXR using one of the following methods:

•Attach the rubber feet and place the unit on a flat surface.

•Fasten a bracket (included) on each side of the unit and attach it to a flat surface.

For more information go to www.kramerav.com/downloads/TP-590TXR.

•Mount the unit in a rack using an optional RK-T2B rack adapter.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your TP-590TXR. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to TP-590TXR.

Setting the DIP Switches

Set the DIP-switches using the table on the right. The

ON/OFF positions are as follows:

•Switch down = ON

•Switch up = OFF

Note: Changes to the DIP-switches only take effect

on power-up.

Function

Status

Range mode

Off—Extended range (provides increased range

at a reduced bandwidth)

On—Normal range (factory default)

Audio source

priority

Off—Embedded audio (factory default)

On—Analog audio

EDID lock

Off—Automatic EDID acquisition (factory

default)

On—Lock (locks the current EDID so that

changes on the output do not result in changes

to the EDID)

Audio mode

selection

Off—Auto (factory default)

On—Manual

Step 5: Connect the power

Connect the 48V DC power supply to TP-590TXR and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power supply that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Operate TP-590TXR

Operate TP-590TXR via:

•Remotely, using Protocol 3000

commands via RS-232 or

Ethernet

•Embedded web pages via the

Ethernet

•Remotely, using an IR remote

control transmitter

Default Parameters

Parameter

Value

Name

KRAMER_

Model

TP-590TXR

IP Address

192.168.1.39

UDP Port

50000

TCP Port

5000

Network Mask

255.255.0.0

Gateway Address

192.168.0.1

RS-232 Baud Rate

115200

Audio delay input switching on newsignal

0 seconds

Audio delay input switching on signal loss (leave 5V on)

5 seconds

Audio delay input switching on cable unplug

0 seconds

Video delay power off 5V on signal loss

15 minutes

HDCP Mode

Followoutput

Protocol 3000 Commands

Command

Description

Command

Description

Protocol handshaking

LOCK-EDID?

Get EDID lock state

AUD-EMB?

Get audio in video embedding status

Set/get protocol permission

AUD-SIGNAL?

Get audio input signal status

LOGOUT

Cancel current permission level

AV-SW-MODE?

Get auto switch mode

MODEL?

Read device model

AV-SW-TIMEOUT

Set/get video auto-switch timeout

NAME

Set/get machine (DNS) name

BUILD-DATE?

Read device build date

NAME-RST

Reset machine name to factory default

(DNS)

CPEDID

Copy EDID data from the output to the input

NET-DHCP

Set/get DHCP mode

DIR

List files in device

NET-GATE

Set/get gateway IP

DISPLAY?

Valid / Invalid output

NET-IP

Set/get IP address

ETH-PORT

Set/get Ethernet port protocol

NET-MAC?

Get MAC address

FACTORY

Resets the device to factory default

NET-MASK

Set/get subnet mask

FS-FREE?

Get file system free space

PASS

Set/get Password

GEDID

Read EDID data

PRIORITY?

Get priority for all channels

GET

Get file

PROT-VER?

Get device protocol version

HDCP-MOD

Set/get HDCP mode

RESET

Reset device

HDCP-STAT?

Get HDCP signal status

SECUR

Start / Stop Security

HELP

Get command list or help for specific

command

SIGNAL?

Get input signal lock status

LDEDID

Write EDID data to input

SN?

Read device serial number

LDFW

Load new firmware

UPGRADE

Perform firmware upgrade

LOAD

Load new firmware

VERSION?

Read device firmware version

Using the Embedded Web Pages

The TP-590TXR can be operated remotely using the

embedded web pages. Access the web pages from the

control computer using a web browser and an Ethernet

connection.

Before attempting to connect:

•Ensure that your browser is supported.

•Ensure that JavaScript is enabled.

Note: In the event that a Web page does not update

correctly, clear your Web browser’s cache.

Note: Only one instance of the web pages can be open at a

time.

To browse the TP-590TXR web pages:

1. Open your Internet browser.

2. Type the IP number of the device (default =

192.168.1.39) in your browser.

If authentication is enabled, the following window

appears.

3. Enter the valid username and password to access the

web pages.

Following a successful logon, the Default page

appears.

Item

Description

Video & Audio

Settings

Viewthe current video and audio

settings.

Reveal Button

Click to reveal the Page Selection

panel.

4. Click the Reveal button to open the left hand side

page panel.

5. Select the required page from the Page Selection

Panel to configure the device:

Video & Audio Settings Page: Modify the video and

timeout parameters.

Device Settings Page:

•View some of the device characteristics (for example,

model and web version)

•Edit IP settings

•Load and save configurations

•Reset the device to factory default settings

EDID Management Page:

•Copy EDID data to either or both of the inputs

•Lock the EDID on each input independently

Note: Do not power up the display before locking the EDID.

Firmware Upgrade Page:

•View the current firmware version

•Upgrade the firmware

Authentication Page: Assign or change logon

authentication details.

About Page: View the Web page version and Kramer

Electronics Ltd company details.

Autres manuels Kramer Émetteur

Kramer

Kramer TP-121EDID Manuel utilisateur

Kramer

Kramer VP-200XLTHD Manuel utilisateur

Kramer

Kramer TP-45EDID Manuel utilisateur

Kramer

Kramer 691 Manuel utilisateur

Kramer

Kramer TP-752T Manuel utilisateur

Kramer

Kramer TOOLS TP-104 Manuel utilisateur

Kramer

Kramer PT-571 Manuel utilisateur

Kramer

Kramer PT-572HDCP+ Manuel utilisateur

Kramer

Kramer 691 Manuel utilisateur

Kramer

Kramer TP-780T Manuel utilisateur

Kramer

Kramer 622T Manuel utilisateur

Kramer

Kramer SID-X3N Manuel d'installation et d'exploitation

Kramer

Kramer 650T Manuel utilisateur

Kramer

Kramer VP-428H2 Manuel utilisateur

Kramer

Kramer TOOLS TP-104 Manuel utilisateur

Kramer

Kramer TP-410 Manuel utilisateur

Kramer

Kramer SID-X1N Manuel utilisateur

Kramer

Kramer DigiTOOLS KW-11T Manuel utilisateur

Kramer

Kramer TP-210 Manuel utilisateur

Kramer

Kramer F-110 Manuel utilisateur

Kramer

Kramer WP-110 Manuel utilisateur

Kramer

Kramer VP-5R Manuel utilisateur

Kramer

Kramer SID-X1 Manuel utilisateur

Kramer

Kramer TP-581T Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur