Kohler K-10673 Manuel d'utilisation

Maintenance Guide

Electronic Valve

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-10673, K-10674, K-10677

1108709-5-C

Table of Contents

EC Declaration of Conformity ............................. 3

Important Information ................................... 4

Your Kohler Electronic Valve .............................. 4

Control Stop Valve Operation ............................. 6

Remove the DC Sensor ................................. 7

Replace the Battery .................................... 8

Reinstall the DC Sensor ................................. 9

Remove the Solenoid .................................. 10

Install the Solenoid .................................... 11

Clean the Screen/Replace the Piston ...................... 12

Clean/Replace the Diaphragm ........................... 14

Replace the Vacuum Breaker ............................ 16

Replace the Flush Button Assembly ....................... 17

Warranty ........................................... 17

Troubleshooting ...................................... 19

Service Parts ........................................ 24

1108709-5-C 2 Kohler Co.

EC Declaration of Conformity

declare under our sole responsibility that our products, ELECTRONIC FLUSH VALVES, models:

We,

Kohler Company

444 Highland Drive, Kohler, WI 53044

Phone 920-457-4441

EC DECLARATION OF CONFORMITY

K-10673

to which this declaration relates, are in conformity with the following standards:

Electromagnetic Compatibility Directive 89/336/EEC of 3 May 1989 as Amended by

92/31/EEC of 28 April 1992 and 93/68/EEC, Article 5 of 22 July 1993, based on:

• IEC 61000/ IEC 61000-3-:

"Electromagnetic Compatibility (EMC)";

Part 3: "Limits".

Section 2. "Limits for harmonic current emissions (equipment input current up to and including

16A per phase" (2000).

Section 3. "Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage

supply systems, for equipment with rated current <16 A per phase and not subjected to

conditional connection" (1995 + A1:2001).

• EN 61000-6-2/ EN 61000-6-2:

"Electromagnetic Compatibility (EMC) – Part 6-2: Generic standards – Immunity for industrial

environments" (2001).

• EN 55022 Class B:

"Information technology equipment – Radio disturbance characteristics – Limits and methods of

measurements" (1998 A1:2000 + A2:2003).

Low Voltage Directive 73/23/EEC of 19 February 1973 as Amended by 93/68/EEC, Article 13 of

22 July 1993, based on:

• EN 60730/1:

"Specification for Automatic Electrical Controls for Household and Similar Use. General

Requirements".

• EN 60730/2/8:

"Specification for Automatic Electrical Controls for Household and Similar Use. Particular

Requirements for Electrically Operated Water Valves, Including Mechanical Requirements".

Timothy J. Stessman

Codes & Standards Dept.

Kohler Company

November 18, 2008

DateSignature

November 18, 2008 08

K-10677

K-10674

K-10678

K-10675

K-10679

K-10676

Kohler Co. 3 1108709-5-C

Important Information

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures.

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•Consult the dealer or an experienced radio/television technician

for help.

Modiﬁcations: Any modiﬁcations made to this device that are not

approved by Kohler Co. may void the authority granted to the user by

the FCC to operate this equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Your Kohler Electronic Valve

Design Features

The valve is designed speciﬁcally for use with 1-1/2″(1.9 cm) top spud

toilets as offered by Kohler Company and others.

The valve is supplied with factory preset timing values. No

programming or adjustment is required.

1108709-5-C 4 Kohler Co.

Your Kohler Electronic Valve (cont.)

Depending upon use, the ″AA″alkaline batteries can be expected to

last for two to three years before replacement is required.

Flush Operations

The exposed electronic valve provides the following ﬂushing

operations:

A wave activated main ﬂush operation: Shortly after the

individual departs the ﬁxture, the valve provides a main ﬂush

that lasts for several seconds.

An automatic 24-hour ﬂush operation: After 24-hours of non-use,

the valve produces a full ﬂush.

Low Battery Indication

The 1.5 volt ″AA″alkaline batteries can be expected to last for two to

three years before replacement is required. When the battery reaches a

certain point in its lifetime, the valve announces the low battery

condition by continuously ﬂashing an LED whenever a user is in

range. The batteries are easily replaced as described in the section

″Replace the Batteries″in this guide.

Seasonal Use

The exposed electronic valve is not designed for operation in freezing

conditions. If freezing conditions are expected, isolate and drain the

valve along with whatever other winterization steps are taken for the

facility.

Mobile Use

The exposed electronic valve is not designed for use in moving

environments such as boats.

Kohler Co. 5 1108709-5-C

Control Stop Valve Operation

NOTICE: Refer to this section throughout the Maintenance Guide

when instructed to close and open the control stop valve.

NOTE: A strap wrench must be used to remove the stop cap and

adjust the valve position.

Using a strap wrench, remove the vandal-resistant stop cap from

the control stop.

To close the stop valve: Turn the valve screw clockwise as far as

it can go.

To open the stop valve: Turn the valve screw counterclockwise as

far as it can go.

When done, place the stop cap on the control stop, then retighten

with a strap wrench.

Wall Flange

Wall Tube

Control Stop

Stop Cap

1108709-5-C 6 Kohler Co.

Remove the DC Sensor

Close the control stop valve.

Using a 3/32″hex wrench, remove the setscrew from the cap.

Carefully lift the cap from the valve body.

Grasp each side of the connector pair, then pull apart the DC

sensor connector from the solenoid. Do not separate the

connector pair by pulling on the wires.

Position the cap on its side.

Using a 3/32″hex wrench, loosen the screw of the wedge lock

system (not shown) that holds the DC sensor in place inside the

cap.

Turn the cap over and slide the sensor into your hand.

NOTE: The batteries inside the sensor may be considered hazardous

waste. Discard the old sensor and/or batteries in accordance with

any applicable codes.

If replacing the DC sensor, discard the old DC sensor and

batteries.

Cap

Setscrew

DC Sensor with Clip

DC Sensor

Connector

Kohler Co. 7 1108709-5-C

Replace the Battery

NOTE: It is not necessary to remove the sensor from the cap to

replace the batteries.

Using a 3/32″hex wrench, remove the two screws from the

bottom of the DC sensor.

Remove the battery cover and pull out the battery holder.

NOTE: The batteries may be considered hazardous waste. Discard

the old batteries in accordance with any applicable codes.

Remove and discard the old batteries. If necessary, use a small

ﬂat-blade screwdriver to pry the batteries from the battery holder.

Align the metal poles on the new battery to contact the metal

electrodes in the battery holder. Take care to properly position

each battery, as shown on the battery holder.

Insert four new 1.5 volt ″AA″alkaline batteries into the battery

holder.

NOTICE: Do not overtighten the screws. The plastic threads can be

easily damaged.

Reinstall the battery holder and battery cover. Retighten the

screws on the battery holder.

DC Sensor

Batteries

Screws

Battery Cover

Battery Holder

1108709-5-C 8 Kohler Co.

Reinstall the DC Sensor

NOTE: The DC sensor must be installed as shown in the

illustration.

Hold the cap horizontally with the sensing holes down and align

the DC sensor with the cap.

Slide the DC sensor into the cap until the sensor eyes align with

the holes in the cap.

Using a 3/32″hex wrench, tighten the screw on the wedge lock

system (not shown) that holds the DC sensor in place in the cap.

Connect the DC sensor connector to the solenoid connector on the

valve. Ensure that the connector pair is fully seated.

Locate the connector assembly adjacent to the sensor body to

prevent pinching when cap is reinstalled on the valve.

Place the cap on the valve body.

Align the sensor eyes toward the user.

NOTICE: Do not overtighten the setscrew. The plastic threads can be

easily damaged.

Secure the cap with the setscrew.

Open the control stop, reinstall the cap, then tighten ﬁrmly with a

strap wrench.

Verify the valve functions.

Cap

Setscrew

DC Sensor with Clip

DC Sensor

Connector

Kohler Co. 9 1108709-5-C

Remove the Solenoid

Close the control stop valve.

NOTE: If the unit has not ﬂushed since the stop valve was closed,

the inlet arm may still be pressurized. Use the manual ﬂush button

to release pressure.

Using a 3/32″hex wrench, remove the setscrew from the cap.

Remove the cap by lifting from the valve body.

Pull the two connectors apart to disconnect the DC sensor

connector from the solenoid connector.

Temporarily store the cap and DC sensor assembly in a safe

place.

Using an adjustable wrench, turn the solenoid assembly

counterclockwise to remove the solenoid assembly from the valve

body.

Valve Body

Diaphragm

Cap

Setscrew

O-Ring

Piston

Retaining Nut

Spring

DC Sensor

Connector

Solenoid

Connector

Solenoid

Assembly

Piston

Cover

1108709-5-C 10 Kohler Co.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Kohler Unité de contrôle

Kohler

Kohler K-13516X Instructions de montage

Kohler

Kohler K-728 Instructions de montage

Kohler

Kohler 880A Manuel utilisateur

Kohler

Kohler K-408 Instructions de montage

Kohler

Kohler K301 Manuel utilisateur

Kohler

Kohler rada VZ1 10 Manuel utilisateur

Kohler

Kohler K-10959 Manuel utilisateur

Kohler

Kohler 5-10EKD Manuel utilisateur

Kohler

Kohler K-407 Manuel utilisateur

Kohler

Kohler TOUCHLESS K-13686 Manuel utilisateur

Kohler

Kohler K-175 Manuel utilisateur

Kohler

Kohler K-2977 Instructions de montage

Kohler

Kohler K-400 Manuel utilisateur

Kohler

Kohler K-402 Instructions de montage

Kohler

Kohler K-2976-KS Instructions de montage

Kohler

Kohler K-528-K1 Instructions de montage

Kohler

Kohler K-2971 Instructions de montage

Kohler

Kohler K-10956 Manuel d'utilisation

Kohler

Kohler ENGLEFIELD K-98095X Instructions de montage

Kohler

Kohler K-5557 Instructions de montage

Kohler

Kohler 28139T-DR Manuel utilisateur

Kohler

Kohler K-14677 Instructions de montage

Kohler

Kohler K-T10669 Instructions de montage

Kohler

Kohler K-76746GL-NA Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur