Kohler K-10956 Manuel d'utilisation
Maintenance Guide
Exposed Electronic Valve
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-10956, K-10957, K-10962
1058866-5-D
Table of Contents
EC Declaration of Conformity ............................. 3
Important Information ................................... 4
Thank You For Choosing Kohler Company ................... 4
Your Kohler Electronic Valve .............................. 5
Care and Cleaning ..................................... 6
Control Stop Valve Operation ............................. 7
Remove the DC Sensor ................................. 8
Replace the Batteries ................................... 9
Install the DC Sensor .................................. 10
Remove the Solenoid .................................. 11
Install the Solenoid .................................... 12
Clean the Screen/Replace the Piston ...................... 13
Clean/Replace the Diaphragm ........................... 15
Replace the Vacuum Breaker ............................ 17
Replace the Flush Button Assembly ....................... 18
One-Year Limited Warranty .............................. 18
Troubleshooting ...................................... 19
Service Parts ........................................ 24
1058866-5-D 2 Kohler Co.
EC Declaration of Conformity
Kohler Company
! "# $%$&
' ( ( ) )*)+,- ,, ( *(',) ./ 00/ 1)2
$& "34 $& "% $& "5 $& ""
$& "3 4 $& "3& $& "3# $& "3
$& "3 $& "3 $& "33
, 6' ,) ', ,) '71,- 6, , 76 ),)2
Electromagnetic Compatibility Directive 89/336/EEC
7 - &"5" ) 1 +-
92/31/EEC
7 #5 * &""#
93/68/EEC
,' 7 ## 8(- &"" +) 2
9
IEC 61000/ IEC 61000-3-:
:',1,' 1*,+,- ;<:=
!, 2 :1,):>
/', #> :1,) 7 1' '(, 1))) ;?(*1, *(, '(, (* , '(
&3 * *): ;# <>
/', > :1,, 7 , ') , 7(',(,) 7'@ *(+' 6$,
)(**- )-),1) 7 ?(*1, 6, , '(, A&3 * *) , )(+B', ,
', '',: ;&"" C &2# &<>
9
E 61000-6-2/ E 61000-6-2:
:',1,' 1*,+,- ;< D !, 3$#2 E' ),) D 11(,- 7 (),
1,): ;# &<>
9
E 55022 Class B:
:71, ,'- ?(*1, D ),(+' '',),') D 1,) 1,) 7
1)(1,): ;&""5 &2# C #2# <>
Low Voltage Directive 73/23/EEC
7 &" +(- &"% ) 1 +-
93/68/EEC
,' & 7
## 8(- &"" +) 2
9
E 60730/1:
:/*'7', 7 (,1,' ',' ,) 7 () /1 .)> E
?(1,):>
9
E 60730/2/8:
:/*'7', 7 (,1,' ',' ,) 7 () /1 .)> !,'(
?(1,) 7 ','- *, , 0) '( '' ?(1,):>
1,- 8> /,))1
) F /,) *,>
Kohler Company
444444
44444 ((), #" # 3
/,(4444 ,
((), #" # 3 3
Kohler Co. 3 1058866-5-D
Important Information
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures.
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/television technician
for help.
Modifications: Any modifications made to this device that are not
approved by Kohler Co. may void the authority granted to the user by
the FCC to operate this equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Thank You For Choosing Kohler Company
Thank you for choosing Kohler Company. Your Kohler Company
product reflects the true passion for design, craftsmanship, artistry, and
innovation Kohler Company stands for. We are confident its
dependability and beauty will surpass your highest expectations,
satisfying you for years to come.
All information in this guide is based upon the latest product
1058866-5-D 4 Kohler Co.
Thank You For Choosing Kohler Company (cont.)
information available at the time of publication. At Kohler Company,
we strive to fulfill our mission of improving the level of gracious living
for each person who is touched by our products and services. We
reserve the right to make changes in product characteristics, packaging,
or availability at any time without notice.
Please take a few minutes to review this guide. Pay special attention to
the care and cleaning instructions.
Your Kohler Electronic Valve
Design Features
The valve is designed specifically for use with 1-1/2″(1.9 cm) top spud
toilets as offered by Kohler Company and others.
The valve is supplied with factory preset timing values. No
programming or adjustment is required.
Depending upon use, the ″AA″alkaline batteries can be expected to
last for two to three years before replacement is required.
Flush Operations
The exposed electronic valve provides the following flushing
operations:
An automatic main flush operation: Shortly after the individual
departs the fixture, the valve provides a main flush that lasts for
several seconds.
An automatic 24-hour flush operation: After 24-hours of non-use,
the valve produces a full flush.
Low Battery Indication
The ″AA″alkaline batteries can be expected to last for two to three
years before replacement is required. When the battery reaches a
certain point in its lifetime, the valve announces the low battery
condition by continuously flashing an LED whenever a user is in
range. The batteries are easily replaced as described in the section
″Replace the Batteries″in this guide.
Replacement batteries can be purchased from drugstores or other stores
stocking batteries. The batteries are standard 1.5 volt ″AA″alkaline
cells (four required).
Seasonal Use
Kohler Co. 5 1058866-5-D
Your Kohler Electronic Valve (cont.)
The exposed electronic valve is not designed for operation in freezing
conditions. If freezing conditions are expected, isolate and drain the
valve along with whatever other winterization steps are taken for the
facility.
Mobile Use
The exposed electronic valve is not designed for use in moving
environments such as boats.
Care and Cleaning
For best results, keep the following in mind when caring for your
KOHLER product:
•Use a mild detergent such as liquid dishwashing soap and warm
water for cleaning. Do not use abrasive cleaners that may scratch
or dull the surface.
•Carefully read the cleaner product label to ensure the cleaner is
safe for use on the material.
•Always test your cleaning solution on an inconspicuous area
before applying to the entire surface.
•Do not allow cleaners to sit or soak on the surface.
•Wipe surfaces clean and rinse completely with water immediately
after cleaner application. Rinse and dry any overspray that lands
on nearby surfaces.
•Use a soft, dampened sponge or cloth. Never use an abrasive
material such as a brush or scouring pad to clean surfaces.
For detailed cleaning information and products to consider, visit
www.kohler.com/clean. To order Care & Cleaning information, call
1-800-456-4537 and press 1 for Kohler Products and then 3 for
Literature.
1058866-5-D 6 Kohler Co.
Control Stop Valve Operation
Use a strap wrench to remove the vandal resistant cap from the
control stop valve.
Close the stop valve by turning the valve screw clockwise as far
as it can go.
Open the stop valve by turning the valve screw counterclockwise
as far as it can go.
When done, place the stop cap on the control stop valve and
tighten using a strap wrench.
Wall Flange
Wall Tube
Control Stop
Stop Cap
Kohler Co. 7 1058866-5-D
Remove the DC Sensor
Close the control stop valve (refer to the ″Control Stop Valve
Operation″section).
Using a 3/32″hex head wrench, remove the setscrew from the
valve cap.
Remove the cap by carefully lifting from the valve body.
Disconnect the DC sensor connector to the solenoid by grasping
each side of the connector pair and pulling apart. Do not separate
the connector pair by pulling on the wires.
Position the cap on its side and look inside.
Remove the wedge clip that holds the DC sensor in place inside
the cap.
Turn the cap over and slide the sensor into your hand.
NOTE: The batteries inside the sensor may be considered hazardous
waste. Discard the old sensor and/or batteries in accordance with
any applicable codes.
If replacing the DC sensor, discard the old DC sensor and
batteries.
Cap
Setscrew
DC Sensor
DC Sensor
Connector
Wedge Clip
1058866-5-D 8 Kohler Co.
Replace the Batteries
NOTICE: Do not over tighten the screws. The plastic threads on the
screws can be easily damaged.
NOTE: When purchasing replacement batteries, select four 1.5 volt
AA alkaline batteries.
NOTE: If replacing the sensor, install a battery in the new sensor
unit before installing the sensor.
NOTE: It is not necessary to remove the sensor from the cap to
replace the batteries.
Using a 3/32″hex wrench, remove the two screws from the
bottom of the DC sensor.
Remove the battery holder from the DC sensor.
Using small flat-blade screwdriver (if necessary), carefully pry the
batteries from the battery holder.
NOTE: The batteries may be considered hazardous waste. Discard
the old batteries in accordance with any applicable codes.
Remove and discard the old batteries.
NOTE: Note the polarity stamped on the battery holder for proper
battery placement.
Insert the new batteries into the battery holder.
Reinstall the battery holder into the DC sensor.
DC Sensor
Batteries
Screws
Battery Holder
Kohler Co. 9 1058866-5-D
Install the DC Sensor
NOTICE: Do not pinch or kink the wires between the cap and the
valve body. If the wires are damaged, the unit may not operate.
Hold the cap horizontally with the sensing holes down and align
the DC sensor with the cap.
Slide the DC sensor into the cap until the sensor eyes align with
the holes in the cap. Ensure the sensor wires are not pinched and
the DC sensor connector hangs free.
Slide the wedge clip between the DC sensor and the cap until
snug.
Connect the DC sensor connector to the solenoid connector on the
valve. Ensure that the connector pair is fully seated.
Locate the connector assembly adjacent to the sensor body to
prevent pinching when cap is reinstalled on the valve.
Place the cap on the valve body.
Align the sensor eyes toward the user.
Secure the cap with the setscrew.
Open the control stop valve (refer to the ″Control Stop Valve
Operation″section).
Reinstall the stop cap onto the control stop and tighten firmly
with a strap wrench.
Verify that the valve functions.
Cap
Setscrew
DC Sensor
DC Sensor
Connector
Wedge Clip
1058866-5-D 10 Kohler Co.
Ce manuel convient aux modèles suivants
5
Table des matières
Langues :
Autres manuels Kohler Unité de contrôle
Kohler
Kohler K-10949 Manuel utilisateur
Kohler
Kohler DTV+ Instructions de montage
Kohler
Kohler K-687 Instructions de montage
Kohler
Kohler K-2977 Instructions de montage
Kohler
Kohler K-175 Manuel utilisateur
Kohler
Kohler K-402 Instructions de montage
Kohler
Kohler K-2971 Instructions de montage
Kohler
Kohler K-10959 Manuel utilisateur
Kohler
Kohler K-728 Instructions de montage
Kohler
Kohler K-307 Manuel utilisateur
Kohler
Kohler DTV+ Konnect K-97999-NA Manuel utilisateur
Kohler
Kohler Rite-Temp K-8300-PX Manuel utilisateur
Kohler
Kohler K-10668 Instructions de montage
Kohler
Kohler K-407 Manuel utilisateur
Kohler
Kohler K-2975 Manuel utilisateur
Kohler
Kohler Mastershower K-406 Manuel utilisateur
Kohler
Kohler GM77177-KP1-QS Manuel utilisateur
Kohler
Kohler K-305 Instructions de montage
Kohler
Kohler K-10675 Manuel d'utilisation
Kohler
Kohler K-10666 Manuel d'utilisation
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
