Kohler K-175 Manuel utilisateur

JOBNAME: No Job Name PAGE: 1 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

Installation Guide

Bath Media Module

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(Ej. K-12345M)

Français, page ″Français-1″

Español, página ″Español-1″

K-175

1093174-2-C

JOBNAME: No Job Name PAGE: 2 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

IMPORTANT INSTRUCTIONS

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

DANGER: Risk of electric shock. Connect only to circuits protected by a Ground-Fault

Circuit-Interrupter (GFCI) or Residual Current Device (RCD). Grounding is required. The unit

should be installed and grounded by a qualiﬁed service representative.

WARNING: Risk of electric shock. A licensed electrician should route all electrical wiring.

WARNING: Risk of electric shock. Disconnect power before servicing.

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before

beginning installation.

CAUTION: Risk of electric shock or product damage. Make sure the power cord is unplugged

before removing the access covers.

CAUTION: Risk of product damage. The media module is rated to operate in temperatures up to

104°F (40°C). Do not install in any location where the temperature may exceed 104°F (40°C).

NOTICE: Follow all plumbing, electrical, and building codes.

NOTICE: Provide generous, unrestricted service access to the media module. Provide access for

servicing. This access must be located immediately next to the media module. Refer to the roughing in

information.

FCC and IC Compliance

The term ″IC:″before the certiﬁcation/registration number only signiﬁes that the Industry Canada

technical speciﬁcations were met.

Contains:

Kohler Company

Model #: 1070734

IC: 4554A-KOHLER044

FCC ID: N82-KOHLER004

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

NOTE:

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC and IC Radiation Exposure Statement for Mobile Devices

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled

1093174-2-C 2 Kohler Co.

JOBNAME: No Job Name PAGE: 3 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

FCC and IC Compliance (cont.)

environment. This equipment should be installed and operated with a minimum distance of 7-7/8″(20 cm)

between the radiator and your body. The transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

Kohler Co. 3 1093174-2-C

JOBNAME: No Job Name PAGE: 4 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

Speciﬁcations

Interface

Ambient Temperature Max 125°F (52°C)

Maximum Relative Humidity 100% condensing (External surface only)

Digital Interface Cable Length (supplied

with digital interface) 30 ft (9.14 m)

Media Module

Ambient Temperature Max 104°F (40°C)

Maximum Relative Humidity 95% non-condensing

Electrical Service 100-240 V, 50/60 Hz, 2.0-0.83 A

Media Module 100-240 V, 50/60 Hz, 2.0-0.83 A

Valve Cable Length (supplied) 30 ft (9.14 m)

Line-in Cable Length 5.6 ft (1.71 m)

Ethernet Cable Length 30 ft (9.14 m)

Tools and Materials

Level Pencil Measuring

Tape

Screwdrivers HammerDrill

• 1" Hole Saw

Plus:

1093174-2-C 4 Kohler Co.

JOBNAME: No Job Name PAGE: 5 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

Roughing-In

Before You Begin

Observe all local plumbing, building, and electrical codes.

Read these instructions and determine all required components along with their installation

locations before beginning this installation.

This manual covers horizontal installation under the bath surround. An access panel must be

provided for servicing.

The media module may also be mounted horizontally under the ﬂoor joists. If mounting under the

ﬂoor, the unit must not be enclosed.

A licensed electrician should install a 15 A 120 V GFCI electrical outlet, within the stud framing, in

close proximity to the media module.

If possible, install the electrical outlet prior to installing the media box.

This media module complies with UL, CSA, and FCC.

To play your personal music ﬁles, you must have one of the following music servers on your

personal computer: Microsoft

Windows

Media Connect, iTunes

, RhapsodyTM, Yahoo!,

Musicmatch

Jukebox, or Fireﬂy Media Server. For information regarding conﬁguring your music

server, refer to the User Interface User Manual.

For best internet music performance, your computer must have a high speed internet connection.

Kohler Co. reserves the right to make revisions in the design of our products without notice, as

speciﬁed in the Price Book.

2-3/4"

(7 cm)

7/16"

(1.1 cm)

2-5/16"

(5.9 cm)

21-5/8" (54.9 cm)

20-1/2"

(52.1 cm) 11/16"

(1.7 cm)

19-3/16"

(48.7 cm)

13" (33 cm) to

19" (48.3 cm)

36-1/4"

(92.1 cm)

10-11/16"

(27.1 cm)

30' (9.1 m)

Valve Cable

(Included)

30' (9.1 m)

5' 7" (1.7 m)

Ethernet Cable

Line In Cable

K-10609-D Accessory Cable Kit

Available Separately

Kohler Co. 5 1093174-2-C

JOBNAME: No Job Name PAGE: 6 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

Installation Overview

For best results, follow the recommended installation sequence below. Refer to content in this guide as well

as the Installation Guides packed with each component of your bathing system.

NOTE: Illustration above shows a typical installation with the preferred installation locations for the

digital interface, media module and the digital mixing valve (optional).

Recommended Installation Sequence

Determine the installation location for the media module, and digital mixing valve (if used).

Frame the island for the bath. Provide a properly dimensioned stud pocket for the media module

(required) and the digital mixing valve (optional).

Determine the location for the access panels (required) for servicing the bath transducers, media

module, and digital mixing valve (if used). Plan the island construction accordingly.

Install the island deck. Use the cut-out templates supplied with the bath when preparing the deck.

Frame the false wall for the digital interface.

Route all plumbing to include: supply lines (spout and handshower), drain line, and valve (if

applicable).

Install the electrical outlet(s) in close proximity to the media module and valve (optional)

installation location(s).

Route the Ethernet cable to a router, if applicable.

Route the digital interface cable to the media module.

Finish the false wall.

Install the digital interface and media module. Follow the installation instructions packed with each

product.

Install the bath and drain.

Connect all cables.

Finish the island walls and install the front and rear access panels.

Rear Access

Panel

Overflow Location (LH Shown)

Front Access Panel

24" (61 cm) Min

36" (91.4 cm) Max

3/4" (1.9cm)

10"

(25.4 cm)

4" (10.2 cm)

Digital Interface

Media Module

34" (86.4 cm)

to Knob

34" (86.4 cm)

to Knob

Outlet

Fill Spout

Digital Mixing Valve

False Wall

Transducers

1093174-2-C 6 Kohler Co.

JOBNAME: No Job Name PAGE: 7 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

1. Determine Components

The media module controls the digital mixing valve, transducers, ″Smart Fill″level sensor, chroma lighting,

and music via the digital interface.

Cables are available for connecting audio (line in) and Ethernet to the media module.

Note: Wireless Ethernet is an option with the media module. However, a wired Ethernet connection is

recommended.

Determine all required components along with their installation locations before beginning the

media module installation.

Refer to the installation guides packed with each product for speciﬁc installation needs.

AC Power

Media Module

Router

Computer Internet

Audio

Source

Ethernet Cable

Line In Cable

AC Power

Below Water

Transducer Cables

Above Water

Transducer Cable

Level Sensor

Cable

Chromatherapy

Lighting Cables

Bath

Digital

Interface

Digital Mixing Valve

(Optional)

Kohler Co. 7 1093174-2-C

JOBNAME: No Job Name PAGE: 8 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

2. Prepare the Site

CAUTION: Risk of product damage. The media module is rated to operate in temperatures up to

104°F (40°C). Do not install in any location where the temperature may exceed 104°F (40°C).

The media module is designed to ﬁt within a 13” (33 cm) to 19” (48.3 cm) wide 2x4 stud cavity. The

cavity should be free of cross bracing and insulation.

Brackets should be positioned 20-1/2″(52.1 cm) apart. Allow enough room to one side of the media

module to accommodate the electrical outlet installation and power cord connection.

Measure 2-5/8″(6.7 cm) to 2-7/8″(7.3 cm) in from the stud face to determine the bracket placement.

Mark the bracket locations with a pencil.

Install a 15 A 120 V GFCI electrical outlet within the stud framing, in close proximity to the media

module.

If used, run the Ethernet cable to the media module installation site.

Outlet

Drip Loop

20-1/2"

(52.1 cm)

13" (33 cm) to

19" (48.3 cm)

Pencil

Media Module

(not installed)

2-5/8" (6.7 cm) to

2-7/8" (7.3 cm)

1093174-2-C 8 Kohler Co.

JOBNAME: No Job Name PAGE: 9 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

3. Install the Mounting Brackets

Align the point of the bracket with the marked locations on the studs.

Hammer one end of the bracket into the stud until the point is embedded.

Level the bracket horizontally and repeat the steps to secure the other end of the bracket to the

opposite stud.

Secure the ends of the bracket using the supplied screws.

Repeat steps to install the second bracket in the stud cavity.

20-1/2" (52.1 cm)

Align the brackets

with the pencil mark.

Pencil

Mark

Pencil

Mark

Kohler Co. 9 1093174-2-C

JOBNAME: No Job Name PAGE: 10 SESS: 17 OUTPUT: Thu Jul 17 13:54:19 2008

4. Install the Media Module

Orient the media module horizontally with the connection ports facing down.

Hook the end of the media module with the bent ﬂange onto the right bracket.

Slide the media module to the top of the stud cavity to allow access for the cable connections below.

Secure the module to the right and left brackets with the screws.

Cable

Connections

Slide up.

Screw

Right Bracket

Secure

with screw.

1093174-2-C 10 Kohler Co.

Autres manuels pour K-175

Table des matières

Autres manuels Kohler Unité de contrôle

Kohler

Kohler K-308 Manuel utilisateur

Kohler

Kohler K-10666 Manuel d'utilisation

Kohler

Kohler K-307 Manuel utilisateur

Kohler

Kohler DTV+ Instructions de montage

Kohler

Kohler ENGLEFIELD K-98095X Instructions de montage

Kohler

Kohler K-682 Manuel utilisateur

Kohler

Kohler Rite-Temp K-8300-PX Manuel utilisateur

Kohler

Kohler 28138T Manuel utilisateur

Kohler

Kohler 1190330-NA Manuel utilisateur

Kohler

Kohler 880A Manuel utilisateur

Kohler

Kohler K-408 Instructions de montage

Kohler

Kohler K-13516X Instructions de montage

Kohler

Kohler TAUT 73193T-4CD Manuel utilisateur

Kohler

Kohler K-10668 Instructions de montage

Kohler

Kohler 5-10EKD Manuel utilisateur

Kohler

Kohler K-402 Instructions de montage

Kohler

Kohler 28209W-NA Manuel utilisateur

Kohler

Kohler K-5557 Instructions de montage

Kohler

Kohler K-10675 Manuel utilisateur

Kohler

Kohler TOUCHLESS K-13686 Manuel utilisateur

Kohler

Kohler DTV+ Konnect K-97999-NA Manuel utilisateur

Kohler

Kohler K-10970 Instructions de montage

Kohler

Kohler Mastershower K-406 Manuel utilisateur

Kohler

Kohler K-528-K1 Instructions de montage

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur