Keysight Technologies i7090 Manuel utilisateur
Keysight i7090 Board Test
System
System Installation
Notices
© Keysight Technologies 2021
No part of this manual may be
reproduced in any form or by any
means (including electronic storage
and retrieval or translation into a
foreign language) without prior
agreement and written consent from
Keysight Technologies as governed by
United States and international
copyright laws.
Manual Part Number
Q3000-96001
Edition
Edition 1, January 2021
Printed in Malaysia
Published by:
Keysight Technologies
1400 Fountaingrove Parkway
Santa Rosa, CA 95403-1738
United States
Warranty
THE MATERIAL CONTAINED IN THIS
DOCUMENT IS PROVIDED "AS IS,"
AND IS SUBJECT TO BEING
CHANGED, WITHOUT NOTICE, IN
FUTURE EDITIONS. FURTHER, TO THE
MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, KEYSIGHT
DISCLAIMS ALL WARRANTIES, EITHER
EXPRESS OR IMPLIED WITH REGARD
TO THIS MANUAL AND ANY
INFORMATION CONTAINED HEREIN,
INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. KEYSIGHT
SHALL NOT BE LIABLE FOR ERRORS
OR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES IN
CONNECTION WITH THE
FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT
OR ANY INFORMATION CONTAINED
HEREIN. SHOULD KEYSIGHT AND THE
USER HAVE A SEPARATE WRITTEN
AGREEMENT WITH WARRANTY
TERMS COVERING THE MATERIAL IN
THIS DOCUMENT THAT CONFLICT
WITH THESE TERMS, THE WARRANTY
TERMS IN THE SEPARATE
AGREEMENT WILL CONTROL.
Technology Licenses
The hardware and/or software
described in this document are
furnished under a license and may be
used or copied only in accordance with
the terms of such license.
U.S. Government Rights
The Software is "commercial computer
software," as defined by Federal
Acquisition Regulation ("FAR") 2.101.
Pursuant to FAR 12.212 and 27.405-3
and Department of Defense FAR
Supplement ("DFARS") 227.7202, the
U.S. government acquires commercial
computer software under the same
terms by which the software is
customarily provided to the public.
Accordingly, Keysight provides the
Software to U.S. government
customers under its standard
commercial license, which is embodied
in its End User License Agreement
(EULA), a copy of which can be found at
http://www.keysight.com/find/sweula.
The license set forth in the EULA
represents the exclusive authority by
which the U.S. government may use,
modify, distribute, or disclose the
Software. The EULA and the license set
forth therein, does not require or
permit, among other things, that
Keysight: (1) furnish technical
information related to commercial
computer software or commercial
computer software documentation that
is not customarily provided to the
public; or (2) relinquish to, or otherwise
provide, the government rights in
excess of these rights customarily
provided to the public to use, modify,
reproduce, release, perform, display, or
disclose commercial computer software
or commercial computer software
documentation. No additional
government requirements beyond
those set forth in the EULA shall apply,
except to the extent that those terms,
rights, or licenses are explicitly required
from all providers of commercial
computer software pursuant to the FAR
and the DFARS and are set forth
specifically in writing elsewhere in the
EULA. Keysight shall be under no
obligation to update, revise or
otherwise modify the Software.
Safety Notices
A WARNING notice denotes a hazard.
It calls attention to an operating
procedure, practice, or the like that, if
not correctly performed or adhered to,
could result in personal injury or death.
Do not proceed beyond a WARNING
notice until the indicated conditions are
fully understood and met.
A CAUTION notice denotes a hazard.
It calls attention to an operating
procedure, practice, or the like that, if
not correctly performed or adhered to,
could result in damage to the product
or loss of important data. Do not
proceed beyond a CAUTION notice until
the indicated conditions are fully
understood and met.
i7090 System Installation 3
System Installation
Safety Notices 4
Before Installation 5
Install Monitor, Mouse and Keyboard 5
Release Press Safety Brackets 6
Install Tower Light 7
Connect Air Supply and SMEMA Cables 9
Connect to Network 10
Open Shutters for Board Access 11
Adjust Conveyor Height and Alignment 12
Power Up the System 13
This guide describes the installation of the Keysight i7090 board test system.
These tools are needed in addition to the tools supplied with the system shipment:
•Allen wrench set (metric)
•12” adjustable wrench
•Ladder
4i7090 System Installation
Safety Notices
Safety Notices
The following general safety instructions must be followed when using,
maintaining, and repairing this equipment. If these instructions are not strictly
followed, the user may be exposed to hazards, or equipment damage may occur.
Keysight Technologies assumes no liability for injury or damage if these instructions
are not followed.
Installation
Before you turn on the power, verify that the AC mains supply voltage
matches the voltage marked on the system specifications plate on the back
of the equipment.
This equipment must be connected to a properly installed earth ground. Do
not operate the equipment until it has been properly earthed by a qualified
electrician.
Overcurrent protection must be provided for this equipment. See the
installation instructions for overcurrent recommendations. Do not operate
the equipment until proper overcurrent protection has been installed by a
qualified electrician.
This equipment is not intended for use near explosive or corrosive hazards.
Operation
Printed circuit board assemblies (PCBAs) may be electrically charged
during the normal test cycle. Do not touch any parts which may be
electrically charged.
Do not remove covers or parts of the equipment enclosure. There are no
operator-serviceable parts inside.
Do not operate damaged equipment.
Servicing
All fuses must be replaced only with fuses of the specified type. Do not
modify the equipment or use unapproved replacement parts.
Before Installation
i7090 System Installation 5
Before Installation
1Verify that site preparation tasks are completed.
2Check the system and the contents of all crates and boxes against the order
and any packing lists.
Install Monitor, Mouse and Keyboard
Install the monitor arm and monitor following the manufacturer’s instructions.
Place the keyboard and mouse on the keyboard tray and connect them to the
system connectors.
6i7090 System Installation
Release Press Safety Brackets
Release Press Safety Brackets
1Open the top front door.
2Unlock the yellow press safety bracket by turning it backwards to release it from
the latch. Do the same on the other side.
Locked
Unlocked
Press safety bracket
Install Tower Light
i7090 System Installation 7
Install Tower Light
1Tighten the nut on the tower light bracket using the adjustable wrench.
2Remove the screws securing the front top panel and remove the panel.
3Remove the two screws for the tower light.
Tighten the nut
Front top panel
8i7090 System Installation
Install Tower Light
4Secure the tower light using the two screws.
5Connect the tower light and system connectors.
6Replace the front top panel.
Connect Air Supply and SMEMA Cables
i7090 System Installation 9
Connect Air Supply and SMEMA Cables
1Remove the bottom rear panel.
2Connect the compressed air supply.
3Use 5-wire SMEMA connections to the upstream and downstream systems.
Main air supply
SMEMA Out
SMEMA In
(behind main power switch)
10 i7090 System Installation
Connect to Network
Connect to Network
If the system will be connected to a network, connect the LAN cable. The LAN port
is near the SMEMA Out.
Autres manuels pour i7090
1
Table des matières
Autres manuels Keysight Technologies Instrument de mesure
Keysight Technologies
Keysight Technologies N9030B Manuel d'installation et d'exploitation
Keysight Technologies
Keysight Technologies N5221/2A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies PNA-L N5230A Manuel utilisateur
Keysight Technologies
Keysight Technologies B2900A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies M9485A Guide de l'utilisateur
Keysight Technologies
Keysight Technologies N9321C Manuel utilisateur
Keysight Technologies
Keysight Technologies P Series Manuel utilisateur
Keysight Technologies
Keysight Technologies U1701B Manuel utilisateur
Keysight Technologies
Keysight Technologies N9030B Manuel utilisateur
Keysight Technologies
Keysight Technologies U5310A Guide de l'utilisateur
Keysight Technologies
Keysight Technologies B2900A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies 34972A Manuel utilisateur
Keysight Technologies
Keysight Technologies M9602A Manuel utilisateur
Keysight Technologies
Keysight Technologies N5221B Manuel utilisateur
Keysight Technologies
Keysight Technologies B2900A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies N778 B Series Manuel utilisateur
Keysight Technologies
Keysight Technologies E2655C Manuel utilisateur
Keysight Technologies
Keysight Technologies N9344C Manuel utilisateur
Keysight Technologies
Keysight Technologies N9030B Manuel d'installation et d'exploitation
Keysight Technologies
Keysight Technologies E5072A Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur