Keysight Technologies N9020A Manuel d'installation et d'exploitation

Notice: This document contains references to Agilent.

Please note that Agilent’s Test and Measurement

business has become Keysight Technologies. For more

information, go to www.keysight.com.

Keysight Technologies

EXA Signal Analyzer, Serial Prefix <MY/SG/US5648

MXA Signal Analyzer, Serial Prefix <MY/SG/US5233

Option HL4, 40 MHz Analysis Bandwidth (B40)

and Microwave Preselector Bypass (MPB)

Upgrade Kit

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9010-90054

Edition

Edition 1, February 2019

Supersedes September 2018

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9010-90054 3

Option HL4, 40 MHz Analysis Bandwidth (B40) + Microwave Preselector Bypass (MPB) Upgrade Kit

Option HL4, 40 MHz Analysis Bandwidth (B40) + Microwave

Preselector Bypass (MPB) Upgrade Kit

Software and test equipment is required for making adjustments and for performance verification

testing.

Information on how to obtain this software can be found at:

www.keysight.com/find/calibrationsoftware

While Keysight does recommend that a full calibration be performed after the installation of this

upgrade, the end user must ultimately determine whether they want this service or not. If a full

calibration is required, arrangements regarding the level of calibration must be made between the

end user and the calibration provider.

Products Affected: N9010A, EXA Signal Analyzer

N9020A, MXA Signal Analyzer

Serial Numbers: N9010A, <MY/SG/US56480000

N9020A, <MY/SG/US52330000

Options: B40, MPB

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysighta

( ) Customer

a. To ensure that these newly installed options are functioning properly, the procedure that follows

includes the requirement of performing certain adjustments and performance verification tests.

However, the completion of these tests does not guarantee that the instrument meets all advertised

specifications.

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

3.0 Hours

5.5 Hours

3.5 Hours

4Installation Note N9010-90054

Introduction

This kit includes parts to upgrade older EXA or MXA signal analyzers with Option 507, 508, 513, or

526 to add Options B40, 40 MHz analysis bandwidth, and MPB, microwave preselector bypass. As a

result, some parts included in this kit will not be needed for upgrading some analyzers (newer

analyzers require fewer parts to be changed). Also, some parts might not be necessary if other

certain options are already installed. As a result, some of the procedures, such as Replace A13A1

Bandpass Filter, might not need to be performed.

In addition to installing the hardware to support options B40 and MPB, licenses for the following

options will also be installed (the 'x' is either 1 for EXA or 2 for MXA):

— N90x0A-B40, 40 MHz Analysis Bandwidth

— N90x0A-B25, 25 MHz Analysis Bandwidth

— N9020A-S40, 40 MHz/Channel Baseband Bandwidth (for use with Option BBA, if also installed;

only included with N9020AK-HL4)

— N90x0A-DP2, Digital Processor & 2 GB Capture Memory

— N90x0A-RTL, Real Time Link

— N90x0A-FS1, Fast Sweep Capability, enabled with B40, DP2, or MPB

— N90x0A-MPB, Microwave Preselector Bypass

— N9060A-3FP, Amplitude Correction and Limit Lines

— N9060A-4FP, TOI and Harmonics

— N9060A-5FP, ACP 18 Carrier Measurement

— N9060A-6FP, TV Trigger and IQ Analyzer Enhancement

The installation procedure begins with an “inventory” of the analyzer serial number,

currently-installed options, installed hardware, and software version. This information will be used

to determine which sub-procedures, if any, can be skipped.

Installation Note N9010-90054 5

Introduction

Installation Kit Parts List

Quantity Description Keysight Part Number

1 A2 Enhanced Analog IF Assembly N9020-60290

1 A3 40 MHz Digital IF Assembly N9020-60165

1 A15 Front End Controller w/ IF MUX N9020-60172

1 W2 Cable Assembly, A2 to A3 N9020-60046

1 Opt HL4 Cable Kit with Wire Markers

(includes cables W36 through W43, listed below)

N9020-60171

1 Coaxial Fixed Attenuator, DC to 26.5 GHz, Option 006, PB Free (AT1) 08493-60026

1 Bracket, PS Bypass Switch 1 E4410-00104

1 Bracket, PS Bypass Switch 2 E4410-00110

1 Cable Assembly, SW - SW2 (W31) E4410-20161

1 Cable Assembly, Switch 2 - YIG Tuned Filter (W32) E4410-20163

1 Cable Assembly, Switch 1 - RF Assembly (W34) E4410-20164

1 Cable Assembly, YIG Tuned Filter - Switch 1 (W33) E4410-20165

1 Cable RF Switch 1 - Switch 2 (W35) N9020-20210

1 Cable Assembly, Switch Control (W30) E4410-60159

1 Cable Assembly, A11J2 to A13J2 (W3) N9020-20101

1 Cable Assembly, J1 to A9 Input (W10) N9020-20141

1 Cable Assembly, A10 Output to A11J1(W9) N9020-20153

2 Coaxial Switch (SW1 and SW2) N1810-60069

1 Bracket HB Switch N9020-00023

1 Bracket, RF Side (for older instruments) N9020-00031

1 Bracket, RF Side (for newer instruments) N9020-00034

1 Microwave Filter Bandpass 5175 MHz Max SMA (A13A1) 0955-2176

1 Cable Assembly RF Semi-R SMA (m) Str SMA (m) Str 65 mm LG (A13W1) E6607-21178

1 Cable Assembly RF Semi-R SMA (m) Str SMA (m) Str 195 mm LG (A13W2) E6607-21179

1 Spacer, Filter Mounting Adapter E6607-25005

1 Cable Assembly, YTF (W22) N9020-60059

1 Cable Assembly, Coaxial 530 mm LG (W43) 8121-1401a

with ends labeled ‘705’ and '18'

1 Cable Assembly, Coaxial 530 mm LG (W42) 8121-1401a

with ends labeled ‘706’ and ‘14’

1 Cable Assembly, Coaxial 530 mm LG (W37) 8121-1401a

with ends labeled ‘900’ and

‘100’

1 Cable Assembly, Coaxial 560 mm LG (W40) 8121-1940a

with ends labeled ‘6’ and ‘17’

1 Cable Assembly, Coaxial 620 mm LG (W38) 8121-1861a

with ends labeled ‘901’ and ‘15’

1 Cable Assembly, Coaxial 240 mm LG (W36) 8121-1862a

with ends labeled ‘902’ and ‘7’

6Installation Note N9010-90054

Introduction

1 Cable Assembly, Coaxial 280 mm LG (W41) 8120-8868a

with ends labeled ‘601’ and ‘19’

1 Cable Assembly, Coaxial 525 mm LG (W39) 8121-2028a

with one end labeled ‘1100’

4 Screw M2 x 0.4 (6 mm long) 0515-0658

3 Screw M2 x 0.4 (14 mm long) 0515-0661

4 Screw M3 x 0.5 (8 mm long) 0515-0372

1 Screw M3 x 0.5 (6 mm long) Flathead 0515-1227

4 Screw M2.5 x 0.45 (20 mm long) 0515-1992

12 Cable Tie, Self-Locking, Nylon Gray 1400-0249

1 Label, Information, AUX IF OUT N9020-80081

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

a. This cable is included in the Option HL4 Cable Kit with Wire Markers, p/n N9020-60171

Quantity Description Keysight Part Number

Installation Note N9010-90054 7

Introduction

Tools Required

—T-8TORXDriver

—T-6TORXDriver

— T-10 TORX Driver

— T-20 TORX Driver

— 5/16-inch torque wrench

— 9/16-inch nut driver

— 1/4-inch socket on 4-pound torque wrench

— Scissors or knife

—Diagonalcutters

— Keysight Calibration and Adjustment Software, N7814A (revision E.06.00 or later)

— Test equipment and computer supported by the X-Series Performance Tests and Adjustment

Software

— EXA or MXA Signal Analyzer Service Guide (as appropriate). This manual is available as:

—http://www.keysight.com/find/n9010a_manuals

—http://www.keysight.com/find/n9020a_manuals

— Microsoft Windows based personnel computer with internet access and USB port

— USB storage device with >2GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

Before you disassemble the instrument, turn the power switch to Standby. After the instrument

has completely shut down, unplug the instrument. Failure to unplug the instrument can result in

personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

8Installation Note N9010-90054

Installation Procedure

Analyzer Information

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show, System. Make note of the

following information from the Show System screen:

Product Number ________________

Serial Number ________________

Instrument S/W Revision ________________

3. Check for the presence of the options listed below in the Show System screen (“x” is 1 for an

EXA and 2 for an MXA). Put a check mark or “X” after each option listed below that appears in

the Show System menu.

N90x0A-503 ______

N9010A-532 ______

N9010A-544 ______

N90x0A-B25 ______

N90x0A-BBA ______

N90x0A-CR3 ______

N90x0A-CRP ______

N90x0A-B40 ______

N90x0A-DP2 ______

N90x0A-MPB ______

4. On the analyzer, press System, Show, Hardware. Note the Part #, Matl Rev, Rev, OF Rev, and

Hw Id of the Front End Controller and Front End in the table below.

5. If the analyzer is equipped with any of the following options (refer to the data in step 3 above),

N90x0A-B40

N90x0A-DP2

N90x0A-MPB

Do not proceed with the installation of this upgrade kit. If any of these options are already

installed, you do not need this upgrade kit, since the necessary hardware is already present.

Assembly Name Part # Matl Rev Rev OF Rev Hw Id

Front End Controller

Front End

Installation Note N9010-90054 9

Installation Procedure

6. Refer to the data in step 3 above. If the analyzer has N90x0A-503, N9010A-532, or

N9010A-544 do not proceed with the installation of this kit. This kit can only be installed in

analyzers with frequency range options 507, 508, 513, and 526.

7. Refer to the data in step 2 above. If the analyzer is an N9010A and the serial number is

≥MY/SG/US56480000 do not proceed with the installation of this kit, This kit is only for older

N9010A and N9020A analyzers.

8. Refer to the data in step 2 above. If the analyzer is an N9020A and the serial number is

≥MY/SG/US52330000 do not proceed with the installation of this kit, This kit is only for older

N9010A and N9020A analyzers.

9. Refer to the data in step 2 above. If the Instrument S/W Revision is earlier than A.10.05, you

must upgrade the instrument software. The hardware and licenses being added with this

upgrade are only supported by software revisions A.10.05 and later.

Even if the Instrument S/W Revision is A.10.05 or later, we recommend upgrading to the latest

software revision to ensure that you get the benefit of any defect fixes that have been made

since A.10.05.

The latest instrument software can be downloaded from the following web site:

http://www.keysight.com/find/xseries_software

10.Refer to the data in step 4 above. If the Front End has a Hw Id of 70, it already has the 150 MHz

wide 1st IF bandpass filter and you do not need to perform the Replace A13A1 Bandpass Filter

procedure.

11.Refer to the data in step 3 and step 4 above. If the analyzer has N90x0A-CR3 and/or

N90x0A-CRP installed, verify that it also has a Front End Controller with Hw Id of 41 or 75. If

the Front End Controller has a Hw ID of 41 or 75, you do not need to perform the Replace Front

End Controller procedure.

10 Installation Note N9010-90054

Installation Procedure

Update Instrument Software

If the analyzer does not have instrument software that supports the new hardware, many errors will

occur onscreen when the analyzer boots up. Updating the instrument software and installing the

necessary licenses before installing the new hardware will help ensure that the hardware

installation was successful.

Go to the following website and determine whether or not the analyzer has the latest instrument

software already installed:

http://www.keysight.com/find/xseries_software

If the analyzer does not have the latest instrument software already installed, download and install

the latest version.

Autres manuels pour N9020A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Keysight Technologies Instrument de mesure

Keysight Technologies

Keysight Technologies M9393A Manuel utilisateur

Keysight Technologies

Keysight Technologies N9344C Manuel utilisateur

Keysight Technologies

Keysight Technologies U2020 X Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N5511A-K26 Manuel utilisateur

Keysight Technologies

Keysight Technologies N9030B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N9000A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N9321C Manuel utilisateur

Keysight Technologies

Keysight Technologies i7090 Manuel utilisateur

Keysight Technologies

Keysight Technologies E4980A Manuel de l'opérateur

Keysight Technologies

Keysight Technologies FieldFox N9912A104 Manuel utilisateur

Keysight Technologies

Keysight Technologies EPM-P Series Mode d'emploi

Keysight Technologies

Keysight Technologies N9030B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N9030B Guide de démarrage rapide

Keysight Technologies

Keysight Technologies N432A Manuel utilisateur

Keysight Technologies

Keysight Technologies M9451A Guide de l'utilisateur

Keysight Technologies

Keysight Technologies N77 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies Streamline Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N6705C Manuel de service

Keysight Technologies

Keysight Technologies N9020A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies C Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N9030B Manuel utilisateur

Keysight Technologies

Keysight Technologies N774 C Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N5241B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N524 A Series Manuel d'installation et d'exploitation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur