Keysight Technologies EXA N9010B Guide de démarrage rapide

Option EXM, External Mixing Upgrade Kit

Keysight N9010B EXA

Signal Analyzer

Installation Note

Notice.

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9010-90067

Edition

Edition 2, March 2017

Supersedes February 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9010-90067 3

Option EXM, External Mixing Upgrade Kit

Software and test equipment is required for making adjustments and for performance verification

testing.

Information on how to obtain this software can be found at:

www.keysight.com/find/calibrationsoftware

While Keysight does recommend that a full calibration be performed after the installation of this

upgrade, the end user must ultimately determine whether they want this service or not. If a full

calibration is required, arrangements regarding the level of calibration must be made between the

end user and the calibration provider.

Introduction

This kit includes parts to upgrade an EXA signal analyzer with frequency range Option 532 or 544 to

add Option EXM, External Mixing.

In addition to installing the hardware to support Option EXM, a license for the following option will

also be installed:

— N9010B-EXM, External Mixing

Products Affected: N9010B EXA

Serial Numbers: All

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

1.5 Hours

1.0 Hoursa

a. To ensure that these newly installed options are functioning properly, the procedure that follows

includes the requirement of performing certain adjustments and performance verification tests.

However, the completion of these tests does not guarantee that the instrument meets all advertised

specifications.

4Installation Note N9010-90067

Option EXM, External Mixing Upgrade Kit

Installation Kit Parts List

Quantity Description Keysight Part Number

1 Adapter- Coaxial Straight Female-SMA to Female-SMA, 50W 1250-1666

1 Washer, Lock, Internal Tooth, ¼ inch 2190-0067

1 Nut-Hex-Double-Chamfer 1/4-36-THD.125-IN-THK, Stainless Steel 2950-0223

1 50 Ohm Termination, SMA male 1810-0118

1 Opt EXM Cable Kit with Wire Markers

(includes cable W26, listed below)

N9010-60009

1 Cable Assembly, External Mixing, Front Panel (W27) N9020-20166

1 Cable Assembly, mmW Front End to W27 (W28)

(for use in millimeter wave analyzers)

N9020-20296

1 Cable Assembly, Coaxial 275 mm LG (W26)

(for use in millimeter wave analyzers) 8121-2025 awith ends

labeled ‘903’ and ‘13’

a. This cable is included in the Opt EXM Cable Kit with Wire Markers, p/n N9010-60009.

1 Label, Warning N9030-80018

5 Cable Ties 1400-0249

12 Screw, M3 x 0.5, (6 mm long), flathead 0515-1946

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

Installation Note N9010-90067 5

Option EXM, External Mixing Upgrade Kit

Tools Required

— T-10 TORX Driver

— T-20 TORX Driver

— 5/16-inch torque wrench

— ¼-inch open-end wrench

—Diagonalcutters

— Keysight Calibration and Adjustment Software, N7814A (revision E.16.00 or later)

— Test equipment and computer supported by the X- Series Performance Tests and Adjustment

Software

— EXA Signal Analyzer Service Guide. This manual is available online at the following URL:

www.keysight.com/find/N9010B_service_guide

— Microsoft Windows based personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

Before you disassemble the instrument, turn the power switch to Standby. After the instrument

has completely shut down, unplug the instrument. Failure to unplug the instrument can result in

personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

6Installation Note N9010-90067

Option EXM, External Mixing Upgrade Kit

Installation Procedure

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show System. Make note of the

following information from the Show System screen:

Product Number: _____________

Serial Number: ______________

Instrument S/W Revision: ______________

3. Check for the presence of one of the following frequency range options listed below in the

Show System. Put a check mark or “X” after the frequency range option listed below that

appears in the Show System menu.

N9010A-503_____

N9010A-507_____

N9010A-513_____

N9010A-526_____

N9010A-532_____

N9010A-544_____

4. If the analyzer is equipped with any of the following frequency range options (refer to the data

in step 3 above):

N9010A-503

N9010A-507

N9010A-513

N9010A-526

do not proceed with the installation of this upgrade kit.

An RF or microwave EXA is not compatible with Option EXM.

Installation Note N9010-90067 7

Option EXM, External Mixing Upgrade Kit

Analyzer Disassembly

Standard Instrument

1. Disconnect the instrument from ac power.

2. Refer to Figure 1, “Instrument Outer Case Removal,”. Using the T-20 driver, remove the 4

screws (1) (two on each side) that attach the handle strap (2) on each side of the instrument.

3. Remove the four key locks from the instrument four bottom feet.

4. Remove the four instrument bottom feet.

5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet

(4) in place.

6. Pull the instrument cover (5) off towards the rear of the instrument.

If the instrument is placed on its face during any of the following procedures, be sure to use a soft

surface or soft cloth to avoid damage to the front panel, keys, or input connector.

Make sure any adapters on the front panel are removed.

If the analyzer has Option PRC, Portable Configuration, refer to the "Option PRC." section on

page 9 to remove the outer case.

8Installation Note N9010-90067

Option EXM, External Mixing Upgrade Kit

Figure 1 Instrument Outer Case Removal

Installation Note N9010-90067 9

Option EXM, External Mixing Upgrade Kit

Option PRC

1. Disconnect the instrument from ac power.

2. Refer to Figure 2, “Bail Handle Removal,”. Using the T-20 driver, remove the four screws (two

on each side) (1) that hold the bail handle (2) to the front frame.

Figure 2 Bail Handle Removal

3. Using the T-20 driver, remove the four screws (two on each side) (6) that hold the strap

handle plugs (5) in place.

10 Installation Note N9010-90067

Option EXM, External Mixing Upgrade Kit

4. Refer to Figure 3, “Option PRC Outer Case Removal,”. Using the T-20 driver, remove the four

screws (including washers) (1) that hold the rear bumpers (2) (two on each side) in place.

Figure 3 Option PRC Outer Case Removal

5. Pull the instrument cover (3) off towards the rear of the instrument.

Autres manuels pour EXA N9010B

Table des matières

Autres manuels Keysight Technologies Instrument de mesure

Keysight Technologies

Keysight Technologies V3500A Manuel utilisateur

Keysight Technologies

Keysight Technologies 34980A Manuel utilisateur

Keysight Technologies

Keysight Technologies 34420A Manuel utilisateur

Keysight Technologies

Keysight Technologies B2901A Manuel utilisateur

Keysight Technologies

Keysight Technologies U1701B Manuel utilisateur

Keysight Technologies

Keysight Technologies U2020 X Series Manuel utilisateur

Keysight Technologies

Keysight Technologies X Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N4960A Manuel utilisateur

Keysight Technologies

Keysight Technologies N2797A Manuel utilisateur

Keysight Technologies

Keysight Technologies B2900A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies B2900B Series Manuel utilisateur

Keysight Technologies

Keysight Technologies M980xA PXIe Manuel utilisateur

Keysight Technologies

Keysight Technologies P Series Mode d'emploi

Keysight Technologies

Keysight Technologies N9020A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N4373E Manuel utilisateur

Keysight Technologies

Keysight Technologies E5061B ENA Series Manuel utilisateur

Keysight Technologies

Keysight Technologies 8970B Manuel utilisateur

Keysight Technologies

Keysight Technologies X Series Manuel utilisateur

Keysight Technologies

Keysight Technologies PNA-X N5241A Manuel utilisateur

Keysight Technologies

Keysight Technologies N5222B Guide de démarrage rapide

Keysight Technologies

Keysight Technologies N9030A Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies N9030B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies ENA Series Manuel utilisateur

Keysight Technologies

Keysight Technologies EXA N9010B Manuel d'installation et d'exploitation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur