H3C PSR3000-54A Manuel utilisateur
i
Contents
Overview ·················································· 1
Front panel ···································································· 2
LEDs············································································ 2
Technical specifications ··················································· 4
Power module configuration·············································· 4
Installing and removing the power module······· 6
Installing the power module··············································· 6
Installing the power module ·········································· 7
Connecting the power cord··········································· 9
Removing a power module ··············································10
Removing the power cord············································11
Removing the power module········································11
1
Overview
H3C SecPath PSR3000-54A is a AC-input and DC-output power
module. It is hot swappable and provides a maximum output of 3000
W.
The power module supports N+1 or N+N redundancy (see "Power
module configuration"). It provides a self-protection mechanism
against input undervoltage, input overvoltage, output overvoltage,
output short circuit, output undercurrent, output overcurrent, and
overtemperature conditions.
IMPORTANT:
The power module shuts down automatically when its
temperature exceeds the acceptable range. When the
temperature returns to the acceptable range, the power
module automatically restarts.
2
Front panel
Figure 1 Front panel
(1) Power input LED (AC OK) (2) Handle
(3) AC input receptacle (4) Latch
(5) Power output LED (DC OK)
(6) Air vents (airflow from the inside to outside)
LEDs
The power module has two LEDs.
3
Table 1 LED description
LED Mark Color Description
Power
input LED AC OK Off
No power input.
Low power input voltage.
The power module has
entered self-protected state.
Green Normal power input.
Power
output
LED
DC
OK
Green Normal power output.
Red
Abnormal power output
(Output short circuit, output
overcurrent, output
overvoltage, output
undervoltage, or remote
shutdown has occurred. The
power module has entered
self-protected state.)
Orange An overtemperature
condition has occurred.
NOTE:
A
fte
r
the circuit breaker of the power module is switched off, the
LEDs on the power module will remain on for a while.
4
Technical specifications
Table 2 Technical specifications
Item Specifications
Rated input voltage 100 to 240 VAC @ 50 or 60 Hz
Rated output voltage 240 VDC
Maximum input current 16 A
Maximum output current 55.6 A
Maximum output power
•1200 W @ 110 VAC
•2400 W @ 175 to 200 VAC
•3000 W @ 220 VAC
Dimensions (H × W × D) 41 × 100 × 332 mm (1.61 × 3.94
× 13.07 in)
Ambient
temperature
Operating
temperature –10°C to +50°C (–14°F to
+122°F)
Storage
temperature –40°C to + 70°C (–40°F to
+158°F)
Power module configuration
Follow these guidelines to configure power modules for the device:
•Determine the total number of power modules based on the
actual power consumption, the power module slot number, and
power redundancy design.
•Determine the power module redundancy design based on the
power source conditions.
5
{When two mains power inputs are provided, you can
configure the power modules in N+N redundancy. N+N must
be not greater than the total number of power module slots.
{When one mains power input is provided, you can configure
the power modules in N+1 or N+N redundancy. N+1 or N+N
must be not greater than the total number of power module
slots.
•For easy usage and maintenance, configure a circuit breaker for
each power input. The rated current of the circuit breaker must
be a minimum of 20 A.
7
Installing the power module
CAUTION:
•To install the power module in a slot to the left of the fan tray
slots, orient the power module with the latch above the
handle.
•To install the power module in a slot to the right of the fan
tray slots, orient the power module with the latch below the
handle.
•To install the power module in a slot above the fan tray
slots, orient the power module with the latch below the
handle.
The following procedure installs the power module in a slot above the
fan tray slots.
To install the power module:
1. Wear an ESD wrist strap, and make sure the strap makes good
skin contact and is correctly grounded.
2. Remove the filler panel from the target slot. As shown in Figure
3, put your forefinger into the hole of the filler panel and pull the
filler panel out along the guide rails.
8
Figure 3 Removing the filler panel
3. Unpack the power module.
4. Correctly orient the power module. Holding the power module
handle with one hand and supporting the power module bottom
with the other, slide the power module along the guide rails into
the slot until the latch on the power module clicks into place.
9
The power module has a disorientation rejection design. If the
power module is oriented incorrectly, you cannot install the
power module into the slot. If you encounter a hard resistance
while inserting the power module, pull out the power module,
reorient it, and then insert it again.
Figure 4 Installing a power module
Connecting the power cord
WARNING!
•Make sure each power cord has a separate circuit breaker.
•Before you connect the power cord, make sure the circuit
breaker for the power cord is turned off.
Autres manuels pour PSR3000-54A
1
Table des matières
Autres manuels H3C Unité de contrôle
H3C
H3C PSR250-12A1 Manuel utilisateur
H3C
H3C S9500 LSB1LB1A0 Manuel utilisateur
H3C
H3C PSR1800-56A Manuel utilisateur
H3C
H3C SecPath AC2500 Manuel utilisateur
H3C
H3C PSR250-12A Manuel utilisateur
H3C
H3C PSR2400-54A Manuel utilisateur
H3C
H3C R6900-FAN Manuel utilisateur
H3C
H3C SecPath NSQ1FAB04B0 Manuel utilisateur
H3C
H3C SecPath M9000 NSQM1CGQ20 Manuel utilisateur
H3C
H3C SecPath NSQ1FAB08D0 Manuel utilisateur
H3C
H3C LSVM152SCFAN Manuel utilisateur
H3C
H3C S9500 LSB1FW2A0 Manuel de la liste des pièces
H3C
H3C PSR650B-12A2-F Manuel utilisateur
H3C
H3C SR6600 SPE-FWM-200 Manuel utilisateur
H3C
H3C EWPA1PCID Manuel utilisateur
H3C
H3C LSBM1WCM2A0 Manuel utilisateur
H3C
H3C LSVM2106SFAN Manuel utilisateur
H3C
H3C LSQ1LBSC0 Manuel utilisateur
H3C
H3C SecPath M9000-AI NSQM5MBSHA1 Manuel utilisateur
H3C
H3C LSQM1TGT24FD0 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
