H3C PSR150-A1 Manuel utilisateur

Contents

Overview······················································ 1

Technical specifications·····························································2

Front panel ············································································· 3

Installing and removing the power module··········· 4

Safety guidelines······································································4

Tools ·····················································································5

Installing and removing the power module ······································5

Installing the power module··················································5

Removing the power module················································6

Connecting the power cord························································· 7

Connecting an AC power cord·············································· 7

Connecting a DC power cord················································8

Overview

The PSR150-A1 is an AC-input and DC-output power module. The

PSR150-D1 is a DC-input and DC-output power module. Both power

modules provide an output voltage of 12 V and a maximum output of 150

These power modules have the following features:

•Provide output overvoltage, short-circuit, overcurrent, and

overtemperature protections. See Table 1 for the protection and

auto-recovery features of the power modules.

•Two power modules can be connected in parallel to achieve 1+1

redundancy and load sharing.

•Hot swappable. When you hot swap a power module, make sure the

device can operate correctly with the remaining power modules.

Table 1 Protection and auto-recovery features

Protection

function Protection

state Support for auto-recovery

Output overvoltage

protection

The power module

is latched and

does not supply

power.

Short-circuit

protection

The power module

does not supply

power.

Automatically restores power

supply after the short circuit

condition is resolved

Overcurrent

protection

The power module

does not supply

power.

Automatically restores power

supply after the output current

decreases to an acceptable range

Overtemperature

protection

The power module

does not supply

power.

Automatically restores power

supply after the temperature

decreases to an acceptable range

IMPORTANT:

After a power module is latched, it cannot restore power supply

automatically after the problems are resolved. Follow this procedure to

restore the power module operation:

1. Disconnect the power cord from the external power supply system.

2. Disconnect the power cord from the power module.

3. Wait a few seconds and then connect the power cord to the powe

module.

4. Connect the power cord to the external power supply system.

Technical specifications

Table 2 Technical specifications

Item Specifications

Rated voltage range

•PSR150-A1

{AC input: 100 VAC to 240 VAC @ 50 Hz or

60 Hz

{DC input: 240 VDC

•PSR150-D1: –48 VDC to –60 VDC

Max voltage range

•PSR150-A1

{AC input: 90 VAC to 264 VAC @ 47 Hz or

63 Hz

{DC input: 192 to 290 VDC

•PSR150-D1: –36 VDC to –72 VDC

Output voltage 12 V

Max output current 12.5 A

Max output power 150 W

Dimensions (H × W × D) 41.1 × 101.6 × 177 mm (1.62 × 4 × 6.97 in)

Operating temperature –5°C to +55°C (25°F to 131°F)

Storage temperature –40°C to +70°C (–40°F to +158°F)

Front panel

Figure 1 PSR150-A1 AC power module

(1) Handle (2) Bail latch

(3) AC-input power receptacle (4) Captive screws

Figure 2 PSR150-D1 DC power module

(1) Handle (2) Captive screws

(3) Screw holes for securing the DC

power cord plug (4) DC-input power receptacle

Installing and removing the power

module

To prevent device damage and personal injury, strictly follow the

installation and removal procedures illustrated in Figure 3 and Figure 4,

respectively.

Figure 3 Installation procedure

Figure 4 Removal procedure

Safety guidelines

To prevent device damage and bodily injury, follow these restrictions and

guidelines when you install or remove the power module:

•Wear an ESD wrist strap and make sure the wrist strap makes good

skin contact.

•Before installing the power module, make sure the operating voltage

of the external power supply system is as required by the power

module, and the output voltage of the power module is as required by

the powered device.

•To avoid bodily injury, do not touch any bare wire or terminal.

•Never place the power module in a wet area and prevent fluid from

flowing into the power module.

•To avoid power module damage, do not open the power module.

When the internal circuits or components of the power module fail,

contact H3C Support.

Tools

Prepare the following tools for installation and removal:

•Flat-blade screwdriver

•Phillips screwdriver

•ESD wrist strap

Installing and removing the power module

CAUTION:

Before installing or removing the power module, make sure no power

cord is connected to the power module.

The installation and removal procedures are similar for the PSR150-A1

and PSR150-D1 power modules. The following procedures use the

PSR150-A1 power module as an example.

Installing the power module

1. Wear an ESD wrist strap, and make sure the wrist strap makes good

skin contact and is reliably grounded.

2. Unpack the power module and verify that the input mode of the power

module is as required.

3. Remove the filler panel, if any, from the target power module slot.

4. Correctly orient the power module. Grasping the module handle with

one hand and supporting the module bottom with the other, insert the

module slowly into the slot along the guide rails. See callout 1

in Figure 5.

To prevent damage to the power module or the connector on the

backplane of the powered device, insert the power module gently.

If you insert the power module upside down, you will encounter a hard

resistance because of the special structure designs of the slot and

power module. You need to pull out the power module, orient it

correctly, and insert it again.

5. Use a Phillips screwdriver to fasten the captive screws on the power

module to secure it in the chassis. See callout 2 in Figure 5.

If the captive screw cannot be tightly fastened, examine the

installation of the power module.

Figure 5 Installing the power module

Removing the power module

1. Wear an ESD wrist strap, and make sure the wrist strap makes good

skin contact and is reliably grounded.

2. Disconnect the power cord from the power module and the external

power supply.

3. Face the power module to be removed from the powered device.

4. Use a Phillips screwdriver to loosen the captive screws on the power

module until the captive screws are disengaged from the powered

device.

5. Grasping the handle of the power module with one hand, pull it part

way out. Then supporting the power module bottom with the other

hand, pull the power module slowly out of the slot along the guide

rails.

6. Put the removed power module into an antistatic bag.

Connecting the power cord

Use an AC power cord to connect an AC power module to the external AC

power supply system. Use a DC power cord to connect a DC power

module to the external DC power supply system.

Connecting an AC power cord

1. As shown by Figure 6,pull the bail latch leftward.

2. As shown by callout 1 in Figure 7,connect one end of the AC power

cord to the AC-input power receptacle.

3. As shown by callout 2 in Figure 7,pull the bail latch rightward to

secure the power cord plug in place.

4. Connect the other end of the AC power cord to the external AC power

supply system.

Figure 6 Connecting an AC power cord (1)

Figure 7 Connecting an AC power cord (2)

Connecting a DC power cord

1. Correctly orient the DC power cord plug, and insert it into the DC-input

power receptacle on the power module.

If you insert the plug upside down, you will feel hard resistance

because of the special structure designs of the DC-input power

receptacle and the plug. You need to remove the plug, orient it

correctly, and insert it again.

2. Use a flat-blade screwdriver to fasten thetwo screws on the DC power

cord plug to secure the plug to the DC-input power receptacle, as

shown by callout 2 in Figure 8.

3. Connect the other end of the DC power cord to the external DC power

supply system.

Figure 8 Connecting a DC power cord

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels H3C Unité de contrôle

H3C

H3C SecPath NSQ1FAB04B0 Manuel utilisateur

H3C

H3C PSR300-12A Series Manuel utilisateur

H3C

H3C SecPath DC2400 Manuel utilisateur

H3C

H3C R6900-FAN Manuel utilisateur

H3C

H3C PSR1600B-12A-B Manuel utilisateur

H3C

H3C PSR6000 Manuel utilisateur

H3C

H3C S9500 LSB1FW2A0 Manuel de la liste des pièces

H3C

H3C PSR180-56A Manuel utilisateur

H3C

H3C LSVM2106SFAN Manuel utilisateur

H3C

H3C LSVM152SCFAN Manuel utilisateur

H3C

H3C LSUM1TGT24FD0 Manuel utilisateur

H3C

H3C PSR2400-54A Manuel utilisateur

H3C

H3C PSR750-A Manuel utilisateur

H3C

H3C PSR2400-12AHAH-B Manuel utilisateur

H3C

H3C NSQM1FWDFGC1 Manuel utilisateur

H3C

H3C LSBM1WCM2A0 Manuel utilisateur

H3C

H3C NSQ1TGS32SF0 Manuel utilisateur

H3C

H3C SecBlade Manuel utilisateur

H3C

H3C PSR3000-54A Manuel utilisateur

H3C

H3C PSR250-12A1 Manuel utilisateur

H3C

H3C LSVM1S9810FAN Manuel utilisateur

H3C

H3C SecPath AC2500 Manuel utilisateur

H3C

H3C SecPath PSR300-12A2 Manuel utilisateur

H3C

H3C LSWM18CQ Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur