DMP Electronics 867 Style W Manuel utilisateur

INSTALLATION GUIDE

867 Style W

LX-Bus Notiﬁcation Module

867 Installation and Programming Guide | Digital Monitoring Products 1

GET STARTED

The 867 module provides one supervised Style W notiﬁcation appliance circuit for powering polarized 12 or 24 VDC

ﬁre notiﬁcation devices on XR150/XR550 Series panels. The module connects to the panel LX‑Bus and provides

ground fault, open, and short condition supervision on the notiﬁcation circuit. The module has four LEDs to indicate

circuit trouble and ground fault conditions, as well as power supply and data monitoring.

The 867 also has a silence switch that allows technicians to disable the module bell output during service and

maintenance checks.

What’s Included

▶One 867 NAC Module

▶One Model 308 10k Ohm Resistor with Leads

▶Hardware Pack

Compatibility

▶XR150/XR550 Series panels

▶505‑12 Series power supplies

867 Installation and Programming Guide | Digital Monitoring Products 2

INSTALLATION

1 Mount the Module

The module can be mounted in a DMP enclosure using the standard 3‑hole

mounting pattern. Refer to Figure 1 as needed during installation.

1. Hold the plastic standos against the inside of the enclosure side wall.

2. Insert the included Phillips head screws from the outside of the enclosure

into the standos. Tighten the screws.

3. Carefully snap the module onto the standos.

2 Address the Module

For more information about addressing and switch locations, refer to Table 1 and Figure 3 respectively.

Set the Bell Output Address

Bell Address switches allow you to set an output number for the module that can be activated by any panel zone,

ﬁre bell output, or burglary bell output. When activated, the module provides a programmed bell output for the

duration of the bell cuto time or until manually silenced by an authorized user.

Set the Supervisory Zone Address

Supervisory Address switches allow you to set the zone address for the module, which is programmed into the

panel as a supervisory zone. A trouble condition on the bell circuit either causes the panel to display a trouble on

the keypads or trips zone outputs and reports the trouble to the central station.

The module occupies a single zone address on the LX‑Bus. For example, on an XR550 Series panel, a module

connected to LX700 with the switches set to 5, 2 would be Supervisory Address zone number 752.

Figure 1: Stando and Module

Installation

SWITCH XR150 SERIES XR550 SERIES

TENS ONES LX500 LX500 LX600 LX700 LX800 LX900

0 0 500 500 600 700 800 900

0 1 501 501 601 701 801 901

0 2 502 502 602 702 802 902

0 3 503 503 603 703 803 903

0 4 504 504 604 704 804 904

... ... ... ... ... ... ... ...

9 5 595 595 695 795 895 995

9 6 596 596 696 796 896 996

9 7 597 597 697 797 897 997

9 8 598 598 698 798 898 998

9 9 599 599 699 799 899 999

Table 1: LX-Bus Addresses

867 Installation and Programming Guide | Digital Monitoring Products 3

Select a Bell Ring Style

The 867 module allows you to specify the cadence of the bell output with the Ring Style header. To select a

bell ring style, place a jumper across the two appropriate pins on the header as shown in Figure 2. For more

information, refer to Table 2.

Wire the Module

Caution: Disconnect all power from the panel before wiring the module. Failure to do so may result in

equipment damage or personal injury.

For power connections, use 22 AWG or larger wire. Refer to Figure 3 when wiring the module.

1. Connect 505‑12 DC positive to module Terminal 1. Connect 505‑12 DC negative to module Terminal 2.

2. Connect module Terminal 3 to bell output positive. Connect module Terminal 4 to bell output negative.

3. Install the included 10k Ohm EOL resistor across module Terminals 3 and 4.

4. If necessary, wire module Terminals 6 and 7 to auxiliary trouble indicators.

5. Wire module Terminals 7 and 8 to N/C trouble contacts.

6. Connect the module 4‑wire harness to the panel LX‑Bus.

Figure 2: Ring Style

Header Detail

Steady

Pulse

Temporal

California Schools

RING

STYL

Table 2: Bell Ring Style Options

JUMPER SETTING BELL CADENCE

Steady On for duration of Bell Cuto time

Pulse 1second on, 1second o for duration of programmed Bell Cuto time

Temporal

Temporal Code 3as deﬁned in NFPA‑72, section A‑3‑7.2(a): 0.5 seconds

on, 0.5 seconds o, 0.5 seconds on, 0.5 seconds o, 0.5 seconds on, 2

seconds o.

California Schools As deﬁned in West's Annotated California Codes, section 32002: Short,

intermittent sounds for 10seconds, then o for 5 seconds.

BELL

+ IN

BELL

- IN

BELL

+ OUT

BELL

- OUT

BELL

TRBL

BELL

TRBL

MON

ATN

BELL SILENCE

BELL NORMAL

MODEL

867

TRBL

TENS ONES

TENS

SUPERVISORY ADDR

BELL ADDRESS

ONES

RING

STYL

DATA

RED

BLACK

BELL

TRBL

GND

FAULT

Trouble and Ground Fault LEDs

Power Supply Trouble and Data LEDs

Ring Style Header

Bell Address Switches

Supervisory Address Switches

Bell Silence Slide Switch

From 505-12 DC +

To N/C Trouble Contact

To LX-Bus

From 505-12 DC –

To Trouble Indicator (optional)

To N/C Trouble Contact

–

To Bell Output –

To Bell Output +

10k Ω EOL

S= Supervised Circuit

All circuits are power limted.

Figure 3: Wiring Connections

867 Installation and Programming Guide | Digital Monitoring Products 4

ADDITIONAL INFORMATION

Wiring Speciﬁcations

DMP recommends using 18 or 22 AWG for all LX‑Bus and Keypad Bus connections. The maximum wire distance

between any module and the DMP Keypad Bus or LX‑Bus circuit is 1,000 feet. To increase the wiring distance, install

an auxiliary power supply, such as a DMP Model 505‑12. Maximum voltage drop between a panel or auxiliary power

supply and any device is 2.0 VDC. If the voltage at any device is less than the required level, add an auxiliary power

supply at the end of the circuit.

To maintain auxiliary power integrity when using 22‑gauge wire on Keypad Bus circuits, do not exceed 500 feet.

When using 18‑gauge wire, do not exceed 1,000 feet. Maximum distance for any bus circuit is 2,500 feet regardless of

wire gauge. Each 2,500 foot bus circuit supports a maximum of 40 LX‑Bus devices.

For additional information refer to the LX‑Bus/Keypad Bus Wiring Application Note (LT‑2031) and the 710 Bus

Splitter/Repeater Module Installation Guide (LT‑0310).

Power Supply

The bell power must be supplied by a regulated, power limited, auxiliary power supply listed for Fire Protective

Signaling with a maximum output of 5 Amps at 12 or 24 VDC. The power supply output positive connects to module

Terminal 1 and power supply output negative connects to module Terminal 2.

The power supply must be supervised and provide a set of Normally Closed trouble contacts that connect to the

Power Supply Monitor zone (Terminals 7 and 8) on the 867 module. An open on the supervision circuit causes the

Power Supply Monitor LED to light and an open condition to be reported on the panel supervisory zone address.

LED Operation

For normal operation, all notiﬁcation devices are connected in parallel on the Style W circuit. An included 10k Ohm

EOL resistor installs at the last device in the circuit. The Style W circuit LED operation is deﬁned as follows:

▶Normal—No LEDs light and the module reports a normal condition on the supervisory zone address.

▶Open or Short—The TRBL LED lights and the module reports an open condition on the supervisory zone

address.

▶Ground Fault—The TRBL and GND FAULT LEDs light and the module reports an open condition on the

supervisory zone address.

Bell Silence Switch

The Bell Silence slide switch allows technicians to test or perform maintenance on the ﬁre system without sounding

the ﬁre alarm notiﬁcation devices. When the switch is placed in the Bell Silence position, the module TRBL LED turns

on and an open condition is reported on the supervisory zone address. After testing, returning the silence switch to

the Bell Normal position returns the module to normal operation.

867 Installation and Programming Guide | Digital Monitoring Products 5

SPECIFICATIONS

Operating Voltage

LX‑Bus 8.0 to 15.0 VDC

Operating Current

LX‑Bus 30 mA maximum

Bell Power 30 mA standby, 86 mA maximum

Alarm Switching

Current 5 Amps @ 12 or 24 VDC

CERTIFICATIONS

▶California State Fire Marshal (CSFM)

▶FCC Certiﬁed Part 15

▶New York City (FDNY)

Underwriters Laboratory (UL) Listed

ANSI/UL 1023 Household Burglar

ANSI/UL 985 Household Fire Warning

ANSI/UL 864 Fire Protective Signaling

18205

Designed, engineered, and

manufactured in Springﬁeld, MO

using U.S. and global components.

LT-0178 1.02 21393

INTRUSION • FIRE• ACCESS• NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modiﬁcations made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Information

This device complies with Industry Canada License‑exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes:

1. l’appareil ne doit pas produire de brouillage, et

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

Table des matières

Autres manuels DMP Electronics Unité de contrôle

DMP Electronics

DMP Electronics ITI 738I Guide d'installation

DMP Electronics

DMP Electronics RoBoard RM-G146 Manuel utilisateur

DMP Electronics

DMP Electronics 734N-WIFI Guide de l'administrateur

DMP Electronics

DMP Electronics 712-8 Manuel utilisateur

DMP Electronics

DMP Electronics X1 Guide d'installation

DMP Electronics

DMP Electronics 736V Manuel utilisateur

DMP Electronics

DMP Electronics 716 Manuel utilisateur

DMP Electronics

DMP Electronics RoBoard RM-G144 Manuel utilisateur

DMP Electronics

DMP Electronics RoBoard RM-G212 Manuel utilisateur

DMP Electronics

DMP Electronics 400 Instructions d'utilisation et d'entretien

DMP Electronics

DMP Electronics 714 Manuel utilisateur

DMP Electronics

DMP Electronics Wiegand 734N Guide d'installation

DMP Electronics

DMP Electronics 865 Manuel utilisateur

DMP Electronics

DMP Electronics 861 Manuel utilisateur

DMP Electronics

DMP Electronics Wiegand 734N Manuel utilisateur

DMP Electronics

DMP Electronics 738Zplus Manuel utilisateur

DMP Electronics

DMP Electronics RoBoard RM-G211 Manuel utilisateur

DMP Electronics

DMP Electronics 1116 Manuel utilisateur

DMP Electronics

DMP Electronics 734 Manuel utilisateur

DMP Electronics

DMP Electronics 714N-POE Guide d'installation

DMP Electronics

DMP Electronics Wiegand 734N Guide d'installation

DMP Electronics

DMP Electronics 717 Manuel utilisateur

DMP Electronics

DMP Electronics 277CAN Manuel utilisateur

DMP Electronics

DMP Electronics 400 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur