DMP Electronics 717 Manuel utilisateur

717 GRAPHIC ANNUNCIATOR MODULE

Installation Guide

DESCRIPTION

CR1

TENS ONES

8 9 10 11 12 13

OUTPUTS

MODEL 717

OUTPUTS

14 15 16 17 18 19

R Y G B 0 1 2 3 4 5 6 7

The 717 Graphic Annunciator

Module provides 20 open collector

annunciator outputs that follow

the armed and bypassed state

of assigned panel zones and is

programmable by setting the

address. The module connects

to the panel 4‑wire LX‑Bus and

is addressed using two on‑board

rotary switches. Install multiple 717

modules on the LX‑Bus to achieve a

variety of remote annunciation and

control applications.

Compatibility

• XR150/XR550Series panels

What is Included?

• One 717 Graphic Annunciator

Module

• Hardware Pack

1MOUNT THE MODULE

The 717 comes in a high‑impact plastic housing that you can

mount directly to a wall, backboard, or other ﬂat surface. For easy

installation, the back of the housing contains multiple holes that

allow you to mount the module on a single‑gang switch box or

ring. Themodule can also be mounted in a DMP enclosure using

the standard 3‑hole mounting pattern. Refer to Figure 2 and

Figure 3 as needed during installation.

1. Hold the plastic standos against the inside of the enclosure

side wall.

2. Insert the included Phillips head screws from the outside of

the enclosure into the standos. Tighten the screws.

3. Carefully snap the module onto the standos.

WIRE THE MODULE

2The 717 module provides two screw type terminal blocks for

connecting LX‑Bus wiring and the wiring from annunciation or

control circuits. Refer to Figure 4 when wiring the module.

Connect red, green, and black wires to the panel LX‑Bus.

For supervised operation, connect the yellow wire to the

panel LX‑Bus. Connect remaining wires as needed. For more

information, refer to “Unsupervised Operation” and “Supervised

Operation”.

Note: The 717 module cannot be installed on the Keypad Bus.

Figure 1: 717 Module

Mounting

holes

Figure 2: Mounting Hole Locations Figure 3: Stando Installation

2 717 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

3Set the 717Module to an address that is used by the panel to turn outputs on and o. For easy addressing, the

module contains two on‑board rotary switches that you can set with a small screwdriver.

Set the module to one of ﬁve addresses to designate the speciﬁc zones for the annunciator outputs to follow.

As shown in Table 1, each module address accommodates a speciﬁc range of 20 LX‑Bus zone numbers.

SWITCH

TENS ONES

XR150SERIES XR550SERIES

LX500 LX500 LX600 LX700 LX800 LX900

0 0 500‑519 500‑519 600‑619 700‑719 800‑819 900‑919

2 0 520‑539 520‑539 620‑639 720‑739 820‑839 920‑939

4 0 540‑559 540‑559 640‑659 740‑759 840‑859 940‑959

6 0 560‑579 560‑579 660‑679 760‑779 860‑879 960‑979

8 0 580‑599 580‑599 680‑699 780‑799 880‑899 980‑999

Table 1: LX‑Bus and Corresponding Zone Numbers

SET THE MODULE ADDRESS

CR1

TENS ONES

8 9 10 11 12 13

OUTPUTS

MODEL 717

OUTPUTS

14 15 16 17 18 19

R Y G B 0 1 2 3 4 5 6 7

Connect annunciator

or control wiring to

outputs -7

Optional LED wiring

50 mA @ 50 VDC max

Connect annunciator or

control wiring to outputs 8-19

Data LED

Address

Switches

Connect to 4-wire

LX-Bus from

expansion module

Red

Yellow

Green

Black

Figure 4: Wiring Diagram

717 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

ADDITIONAL INFORMATION

Wiring Speciﬁcations

DMP recommends using 18 or 22 AWG for all LX‑Bus and Keypad Bus connections. The maximum wire distance between

any module and the DMP Keypad Bus or LX‑Bus circuit is 10 feet. To increase the wiring distance, install an auxiliary

power supply, such as a DMP Model 505‑12. Maximum voltage drop between a panel or auxiliary power supply and any

device is 2.0 VDC. If the voltage at any device is less than the required level, add an auxiliary power supply at the end of

the circuit.

To maintain auxiliary power integrity when using 22‑gauge wire on Keypad Bus circuits, do not exceed 500 feet. When

using 18‑gauge wire, do not exceed 1,000 feet. Maximum distance for any bus circuit is 2,500 feet regardless of wire

gauge. Each 2,500 foot bus circuit supports a maximum of 40 LX‑Bus devices.

For additional information refer to the LX‑Bus/Keypad Bus Wiring Application Note (LT‑2031) and the 710 Bus Splitter/

Repeater Module Installation Guide (LT‑0310).

Panel Zone and Keypad Bus Zone Annunciation

When the module is connected to LX‑Bus 1, the addresses in Table 2 and Table 3 allow the annunciator outputs to follow

the armed activity of the panel and Keypad Bus zones using the annunciator output terminal number.

Note: The 717 follows the ﬁrst eight panel zones, Keypad Bus zones 11 to 44 or Keypad Bus zones 51 to 84. To follow

Keypad Bus zones 91 to 164 on an XR150/XR550 Series panel, install multiple 716 modules. For more information,

refer to the 716 Output Expansion Module Installation Guide (LT‑0183).

ADDRESS 01 ADDRESS 11 ADDRESS 51

Zone Terminal Zone Terminal Zone Terminal Zone Terminal Zone Terminal Zone Terminal Zone Terminal

11 0 23 6 41 12 51 0 63 6 81 12

12 1 24 7 42 13 52 1 64 7 82 13

13 2 31 8 43 14 53 271 8 83 14

— — 14 3 32 9 44 15 54 3 72 9 84 15

— — 21 4 33 10 — — 61 473 10 — —

— — 22 5 34 11 — — 62 5 74 11 — —

Table 2: 717 Addresses for XR150/XR550 Series Panels and Keypad Bus Zones

Supervised Operation

To install the module as a supervised device, connect all four LX‑Bus wires from the module to the panel LX‑Bus and

program an appropriate zone as a Supervisory (SV) type. The module may use any address for supervision, provided

that a Supervisory zone is programmed for that address. For example, if a supervised module loses communication with

the panel, an open condition (Trouble) is indicated on its Supervisory zone.

When installing Zone Expander modules on the same LX‑Bus as a supervised module, start their address at the next

zone number. For example, a module set to address 20 uses zone 520 for supervision. A zone expander on the same bus

would be set to address 21 to start at zone 521 for an XR150/XR550 Series panel. Refer to Table 3.

717 ADDRESS 00 01 11 20 40 51 60 80

XR550 SUPERVISORY

ZONES

500 501 511 520 540 551 560 580

600 N/A N/A 620 640 N /A 660 680

700 N /A N /A 720 740 N/A 760 780

800 N/A N/A 820 840 N /A 860 880

900 N/A N/A 920 940 N /A 960 980

Table 3: 717 Addresses and Supervisory Zones

Unsupervised Operation

To operate the module in unsupervised mode, do not connect the yellow wire from the module to the panel LX‑Bus.

Unsupervised operation allows you to install multiple modules and set them to the same address. Do not program a zone

address for unsupervised operation.

Designed, engineered, and

manufactured in Springﬁeld, MO

using U.S. and global components.

LT-0235 1.02 20105

717 GRAPHIC

ANNUNCIATOR MODULE

Speciﬁcations

Operating Voltage 8.8 VDC to 15.0 VDC

Operating Current 10 mA + 1 mA per active output

Switched Ground Rating 50 mA at 30 VDC Max.

each output

Enclosure Dimensions 4.5” W x 2.75” H x 1.75” D

Ordering Information

717 Graphic Annunciator Module

Accessories

300 4-Wire Harness

Compatibility

XR150/XR550 Series Panels

Certiﬁcations

California State Fire Marshal (CSFM)

New York City (FDNY COA #6167)

Underwriters Laboratory (UL) Listed

ANSI/UL 365 Police Connected Burglar

ANSI/UL 464 Audible Signal Appliances

ANSI/UL 609 Local Burglar

ANSI/UL 864 Fire Protective Signaling

ANSI/UL 985 Household Fire Warning

ANSI/UL 1023 Household Burglar

ANSI/UL 1076 Proprietary Burglar

CR1

TENS ONES

8 9 10 11 12 13

OUTPUTS

MODEL 717

OUTPUTS

14 15 16 17 18 19

R Y G B 0 1 2 3 4 5 6 7

INTRUSION • FIRE• ACCESS• NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

Changes in Armed Zone States

The module’s 20 power limited annunciator outputs follow the armed state of their respective zones in normal, open, and

shorted conditions. Refer to Table 4.

For example on an XR150/XR550 Series panel, annunciator output Terminal 1 on a module set to address 00 shorts to

ground each time zone 501 is in trouble. If the zone is wireless, Terminal 1 shorts to ground when the wireless point has

a low battery or is missing. This feature allows the panel to operate control relays, or to light lamps or LEDs, to indicate

changes in the state of speciﬁc zones.

ARMED ZONE STATE 717ANNUNCIATOR OUTPUT ACTION

Normal O—No ground reference

Trouble, wireless low battery, missing On—Steady short to ground

"A" or "L" in Report to Transmit Pulse (1.6seconds On, 1.6seconds O)

Zone Bypassed Slow pulse (1.6seconds On, 4.8seconds O)

Table 4: Annunciator Outputs

Autres manuels DMP Electronics Unité de contrôle

DMP Electronics

DMP Electronics 277CAN Manuel utilisateur

DMP Electronics

DMP Electronics 263EXT Manuel utilisateur

DMP Electronics

DMP Electronics 736P Radionics Guide d'installation

DMP Electronics

DMP Electronics RoBoard RM-G211 Manuel utilisateur

DMP Electronics

DMP Electronics 738Zplus Manuel utilisateur

DMP Electronics

DMP Electronics 736P Radionics Manuel utilisateur

DMP Electronics

DMP Electronics 714-D22 Manuel utilisateur

DMP Electronics

DMP Electronics 861 Manuel utilisateur

DMP Electronics

DMP Electronics 738ZplusINT Manuel utilisateur

DMP Electronics

DMP Electronics XR100 Manuel utilisateur

DMP Electronics

DMP Electronics 865 Manuel utilisateur

DMP Electronics

DMP Electronics 714N-POE Guide d'installation

DMP Electronics

DMP Electronics 734 Manuel utilisateur

DMP Electronics

DMP Electronics 736V Manuel utilisateur

DMP Electronics

DMP Electronics 1116 Manuel utilisateur

DMP Electronics

DMP Electronics 708 Manuel utilisateur

DMP Electronics

DMP Electronics 734INT Guide d'installation

DMP Electronics

DMP Electronics RoBoard RM-G145 Manuel utilisateur

DMP Electronics

DMP Electronics 867 W LX-BUS Manuel utilisateur

DMP Electronics

DMP Electronics 734 Guide d'installation

DMP Electronics

DMP Electronics ITI 738I Guide d'installation

DMP Electronics

DMP Electronics 400 Instructions d'utilisation et d'entretien

DMP Electronics

DMP Electronics 734N Series Guide d'installation

DMP Electronics

DMP Electronics 734 Guide d'installation

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur