DMP Electronics 734 Guide d'installation

INSTALLATION AND PROGRAMMING GUIDE

734 Weigand

Interface Module

About the 734............................................. 1

Power Supply......................................................... 1

Zone Terminals ...................................................... 1

Annunciators.......................................................... 1

Indicator LEDs ....................................................... 1

Form C Relay......................................................... 2

Programming Connection................................ 2

Keypad In and Out Connections ................... 2

PCB Features...............................................3

Install the 734 .............................................4

Mount the 734 ...................................................... 4

Wire the Electronic Lock.................................. 5

Isolation Relay ...................................................... 6

Install the 333 Suppressor ............................... 7

Wire the Zone Terminals................................... 8

Connect a Card Reader....................................10

Set the 734’s Address.......................................12

TABLE OF CONTENTS

Program the 734....................................... 15

Program Start Display ......................................15

Initialization Option ...........................................15

Initialize Conﬁrm Option .................................16

Activate Zone 2 Bypass ...................................16

Zone 2 Bypass Time ..........................................17

Relock on Zone 2 Change...............................17

Activate Zone 3 Request to Exit ..................18

Zone 3 REX Strike Time...................................19

Activate On-board Speaker ...........................19

Custom Card Deﬁnitions ........................ 20

Card Options.......................................................20

Wiegand Code Length .....................................21

Site Code Position and Length .....................21

User Code Position and Length....................21

Site Code ..............................................................22

Enter Site Code..................................................23

Number of User Code Digits.........................23

No Communication with Panel ....................24

Remove Keypad.................................................25

Keypad Bus Wiring Speciﬁcations........ 26

Public Card Formats ................................27

Compliance Listing Speciﬁcations ........28

UL Commercial Fire..........................................28

UL Access Control.............................................28

ULC Commercial Burglary (XR150/XR550

Series Panels)......................................................28

Certiﬁcations............................................ 29

Underwriters Laboratory (UL Listed)........29

Product Speciﬁcations ........................... 30

Readers and Credentials ......................... 31

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 1

ANNUNCIATORS

An on-board programmable piezo provides local

annunciation at the 734. You can also connect a

variety of switched ground annunciators to the

734 for remote annunciation.

INDICATOR LEDS

The 734 provides three indicator LEDs. The red

LED turns on for the same duration as the door

strike relay. The yellow LED turns on for one

second to indicate receipt of a valid Wiegand

input. The green LED indicates that data is being

sent to the panel.

The 734 Wiegand Interface Module allows you to use the powerful built-in access control capability of

DMP Panels. DMP panels provide access control, arming, and disarming using proximity, mag-stripe,

biometric or other Wiegand-output authentication devices.

Connect a 734 to a DMP panel’s keypad bus or AX-Bus™to use the powerful built-in access control

capability of DMP panels. The 734 includes the following features:

POWER SUPPLY

The 734 operates at 12/24VDC from the power

supply supporting a door’s magnetic lock or

door-strike. It also provides a 10 Amp Form C

relay contact for lock control.

ZONE TERMINALS

Zones 1, 2, and 3 on the 734 can be programmed

for a variety of burglary or access control

applications. Zone 4 is a class B, style A circuit

that may be programmed as a ﬁre zone.

ABOUT THE 734

2 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

FORM C RELAY

The 734’s Form C relay draws up to 35mA of

current. Refer to the NC/C/NO (Dry Contact

Relay) and the Isolation Relay sections in this

document for more information.

PROGRAMMING CONNECTION

The 734 also provides a keypad programming

connection that allows you to use a standard

DMP LCD keypad for initial setup. Programming

can be completed using a keypad connected to

the 734 or from XR150/XR550 or

XR150INT/XR550INT Series panels.

KEYPAD IN AND OUT

CONNECTIONS

The keypad in (KYPD IN) connection receives

and transmits data to the panel keypad bus or

AX-Bus™.

The keypad out (KYPD OUT) connection receives

and transmits data out to other keypad(s) or

module(s). Install a dual connector four-position

harness to allow daisy chain connection to other

devices, up to the maximum number of devices

supported. XR150 Series panels support up to

8devices. XR550 Series panels support up to

16devices. When using the AX-Busses with

XR550 devices, you can have 32 doors,

expandable to 96.

When the 734 is powered from 24VDC, do

not connect devices to KYPD OUT header.

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 3

PCB FEATURES

RED

PROG

RED

KYPD OUT

DATA

XMT LED

WIEGAND

READ LED

RELAY

GRN

YEL

RED + –

Piezo

1234 5 6 7 810 11 12 13 14

LC ASRED WHT GRN BLK Z1 Z2 Z3 Z4+ Z4–RA GND GND

KYPD IN RED

DOOR RELAY

TERMINAL

WEIGAND

INPUTS

STATUS

INDICATOR

OUTPUTS ZONES

TO PANEL

KEYPAD BUS

OR AX-BUS

TO OTHER

KEYPAD BUS

OR AX-BUS

PIEZO

INDICATOR

LEDS

KEYPAD

PROGRAMMING

HEADER

ADDRESS DIP

SWITCHES

Figure 1: PCB Features

4 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

INSTALL THE 734

The 734 comes in a high-impact plastic housing that you can mount directly to a wall, backboard,

or other ﬂat surface.

For easy installation, the back and ends of the 734 housing have wire entrances. The back also

contains multiple mounting holes that allow you to mount the 734 on a single-gang switch box.

DMP recommends mounting the 734 near the protected door. See Figure2 for mounting hole

locations on the housing base.

1MOUNT THE 734

Mounting Hole

Figure 2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 5

The 734 provides a Form C (SPDT) relay for controlling locks and other electronically-controlled

barriers. The three relay terminals marked NO C NC allow you to connect the device wiring to

the relay for module control.

Use an additional power supply to power magnetic locks and door strikes. See Figures 3 and 4

for typical magnetic lock and door strike wiring.

The Form C relay draws up to 35mA of current and contacts are rated for 10 Amps (resistive)

at 12/24VDC. When connecting multiple locks to the Form C relay, the total current for all locks

cannot exceed 10 Amps. If the total current for all locks exceeds 10 Amps, problems may arise

and an isolation relay may be needed. See the Isolation Relay section for information.

2WIRE THE ELECTRONIC LOCK

PROG

RED RED

KYPD IN

DATA

XMT LED

WIEGAND

READ LED

RELAY

NCCNO

GRNYELRED

Model 333

Supressor

Normally Closed

–

Magnetic Door Lock

12/24 VDC

Power Supply

Figure 3: Typical

Magnetic Lock Wiring

PROG

RED

DATA

XMT LED

WIEGAND

READ LED

RELAY

NCCNO

GRNYELRED

Model 333

Supressor

Normally Open

–+

DC Door Strike

12/24 VDC

Power Supply

Figure 4: Typical Door

Strike Wiring

6 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

The Form C relay can control a device that draws less than 10 Amps of current. If a device draws

more than 10 Amp of current, or the sum of all devices controlled by the Form C relay exceeds

10 Amps, an isolation relay must be used. Refer to Figures 5 and 6 for isolation relay wiring.

3ISOLATION RELAY

RED

PROG

RED

KYPD IN

KYPD OUT

DATA

XMT LED

WIEGAND

READ LED

RELAY

NCCNO

GRNYELRED + –

Piezo

Model 333

Supressor

Normally Open

–+

Magnetic Lock

–+

Isolation Relay

To Panel

Keypad Bus

12/24 VDC

Power

Supply

NCCNO

Figure 5: Magnetic Lock with

an Isolation Relay

RED

PROG

RED

KYPD IN

KYPD OUT

DATA

XMT LED

WIEGAND

READ LED

RELAY

NCCNO

GRNYELRED + –

Piezo

Model 333

Supressor

Normally Open

–+

DC Door Strike

–+

Isolation Relay

To Panel

Keypad Bus

12/24 VDC

Power

Supply

NCCNO

Figure 6: Door Strike with

an Isolation Relay

(optional)

Autres manuels pour 734

Table des matières

Autres manuels DMP Electronics Unité de contrôle

DMP Electronics

DMP Electronics RoBoard RM-G144 Manuel utilisateur

DMP Electronics

DMP Electronics 861 Manuel utilisateur

DMP Electronics

DMP Electronics 893A Manuel utilisateur

DMP Electronics

DMP Electronics 711S Manuel utilisateur

DMP Electronics

DMP Electronics 893A Manuel utilisateur

DMP Electronics

DMP Electronics RoBoard RM-G146 Manuel utilisateur

DMP Electronics

DMP Electronics RoBoard RM-G212 Manuel utilisateur

DMP Electronics

DMP Electronics 712-8 Manuel utilisateur

DMP Electronics

DMP Electronics 1134 Guide d'installation

DMP Electronics

DMP Electronics 714N-POE Guide d'installation

DMP Electronics

DMP Electronics 734 Guide d'installation

DMP Electronics

DMP Electronics 714 Manuel utilisateur

DMP Electronics

DMP Electronics 717 Manuel utilisateur

DMP Electronics

DMP Electronics Wiegand 734N Manuel utilisateur

DMP Electronics

DMP Electronics 865 Manuel utilisateur

DMP Electronics

DMP Electronics 714-D22 Manuel utilisateur

DMP Electronics

DMP Electronics myQ 736Q Instructions de montage

DMP Electronics

DMP Electronics Wiegand 734N Manuel utilisateur

DMP Electronics

DMP Electronics SCS-104 Manuel utilisateur

DMP Electronics

DMP Electronics 734N-WIFI Guide de l'administrateur

DMP Electronics

DMP Electronics 400 Instructions d'utilisation et d'entretien

DMP Electronics

DMP Electronics 277CAN Manuel utilisateur

DMP Electronics

DMP Electronics 867 W LX-BUS Manuel utilisateur

DMP Electronics

DMP Electronics 734N Series Guide d'installation

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur