DeWalt Emglo D55152 Manuel utilisateur

D55151, D55152, D55153, D55155

Contractor’s Electric 4 Gallon Hand Carry Air Compressor

Compresseurs d’air portatifs électriques de 4 gallons de classe entrepreneur

Compresor de aire portátil elèctrico de 4 galones para contratistas

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

If you have questions or comments, contactus.

Pour toute question ou tout commentaire,nouscontacter.

Si tiene dudas o comentarios,contáctenos.

1-800-4-

DeWALT

• www.

DeWALT

.com

English

A. On/Off Switch

B. Air Tank Pressure Gauge

C. Regulated Pressure Gauge

D. Pressure Regulator

E. Quick Connects (if equipped)

F. Check Valve

G. Safety Valve

H. Air Tank Drain Valve

I. Power Cord Wrap

J. Pressure Switch

K. Pump Oil Dipstick

L. Pump Oil Drain Plug

M. Motor Reset

N. Air Intake Filter

Air Compressor

NOT A

STEP D

FIG. 1

English

Speciﬁcations

MODEL D55151 D55152 D55153 D55155

WEIGHT 56 lbs. (25.4 kg) 65 lbs. (29.5 kg) 58 lbs. (28.3 kg) 61 lbs. (27.7 kg)

HEIGHT 16.75" (425.5 mm) 16.0" (406.4 mm) 16.75" (501.7 mm) 12.5" (317.5 mm)

WIDTH 18.0" (457.2 mm) 18.0" (457.2 mm) 18.0" (457.2 mm) 21.75" (552.5 mm)

LENGTH 15.0 (381 mm) 18.0" (457.2 mm) 15.0 (381 mm) 21.75" (552.5 mm)

AIR TANK CAPACITY (GALLONS) 4.0 (15.1 liters) 4.0 (15.1 liters) 4.0 (15.1 liters) 4.0 (15.1 liters)

APPROX CUT-IN PRESSURE

95 PSI (655 kPa) 95 PSI (655 kPa) 95 PSI (655 kPa) 100 PSI (689.5 kPa)

APPROX. CUT-OUT PRESSURE

125 PSI (861.8 kPa) 125 PSI (861.8 kPa) 125 PSI (861.8 kPa) 125 PSI (861.8 kPa)

SCFM @ 100 PSI (689.5 kPa) 3.2 3.8 3.8 4.5

MOTOR 1.1 hp (continuous) 1.1 hp (continuous) 1.1 hp (continuous) 1.2 hp (continuous)

Volts/Amps/Hertz 120V/12.5 A/60 Hz. 120V/14 A/60 Hz. 120V/14 A/60Hz. 120V/15 A/60Hz.

RPM 3450 3450 3450 3450

Minumum Branch Circuit

Requirement 15 Amp 15 Amp 15 Amp 15 Amp

PUMP OIL CAPACITY 6 oz. (177.4 ml) 12 oz. (354.9 ml) 12 oz. (354.9 ml) 4 oz. (118.3 ml)

DUTY CYCLE 5 MINUTES ON / 5

MINUTES OFF 5 MINUTES ON / 5

MINUTES OFF

English

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or seriousinjury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or seriousinjury.

CAUTION: Indicates a potentially hazardous

situation which,if not avoided,may result in minor or

moderateinjury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in propertydamage.

PUMP

CYLNDER

AND HEAD

Hot Surfaces

FIG. 2

OUTLET TUBE CHECK

VALVE CHECK

VALVE

OUTLET TUBE

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY

DeWALT

TOOL, CALL US TOLL FREE AT:

1-800-4-D

WALT (1-800-433-9258)

Important Safety Instructions

WARNING: Do not operate this unit until you read and

understand this instruction manual for safety, operation and

maintenanceinstructions.

WARNING: Some dust created by power sanding, sawing,

grinding,drilling,and other construction activities contains chemicals

known to the State of California to cause cancer,birth defects or other

reproductive harm. Some example of these chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and cement and other masonry

products

• arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often

you do this type of work. To reduce your exposure to these

chemicals: work in a well ventilated area,and work with approved

safety equipment, always wear OSHA/MSHA/NIOSH approved,

properly tting face mask or respirator when using suchtools.

When using air tools, basic safety precautions should always be

followed to reduce the risk of of personalinjury.

WARNING: This product contains chemicals, including lead,

known to the State of California to cause cancer, and birth

defects or other reproductive harm. Wash hands afterhandling.

SAVE THESE INSTRUCTION

English

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• It is normal for electrical

contacts within the motor

and pressure switch

to spark.

• Always operate the

compressor in a well

ventilated area free of

combustible

materials, gasoline,

or solvent vapors.

• If electrical sparks from

compressor come into

contact with flammable

vapors, they may ignite,

causing fire or explosion.

• If spraying flammable

materials, locate compressor

at least 20 feet (6.1 m)

away from spray area. An

additional length of hose may

be required.

• Store flammable materials

in a secure location away

from compressor.

• Restricting any of the

compressor ventilation

openings will cause

serious overheating and

could cause fire.

• Never place objects against

or on top of compressor.

• Operate compressor in

an open area at least 12"

(30.5 cm) away from any

wall or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

• Operate compressor in a

clean, dry well ventilated

area. Do not operate

unit indoors or in any

confined area.

• Unattended operation of

this product could result in

personal injury or property

damage. To reduce

the risk of fire, do not

allow the compressor to

operate unattended.

• Always remain in attendance

with the product when it

is operating.

• Always turn off and unplug

unit when not in use.

English

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air

directly from your

compressor is not safe

for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminant's can cause

serious injury or death.

• Air obtained directly from the

compressor should never

be used to supply air for

human consumption. In order

to use air produced by this

compressor for breathing,

suitable filters and in-line

safety equipment must be

properly installed. In-line

filters and safety equipment

used in conjunction with the

compressor must be capable

of treating air to all applicable

local and federal codes prior

to human consumption.

• Sprayed materials such

as paint, paint solvents,

paint remover, insecticides,

weed killers, may

contain harmful vapors

and poisons.

• Work in an area with good

cross ventilation. Read and

follow the safety instructions

provided on the label or

safety data sheets for the

materials you are spraying.

Always use certified safety

equipment: OSHA/MSHA/

NIOSH respiratory protection

designed for use with your

specific application.

DANGER: RISK OF INJURY OR PROPERTY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Oil can leak or spill

and could result in fire

or breathing hazard;

serious injury or death

can result. Oil leaks will

damage carpet, paint or

other surfaces in vehicles

or trailers.

• Always place compressor

on a protective mat when

transporting to protect

against damage to vehicle

from leaks. Remove

compressor from vehicle

immediately upon arrival at

your destination. Always keep

compressor level and never

lie on its side.

WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed

and may be UM coded (for units with air tanks greater than 6

inch diameter) according to ASME Section VIII, Div. 1 rules. All

pressure vessels should be inspected once every two years. To

nd your state pressure vessels inspector, look under the Division

of Labor and Industries in the government section of a phone

book or call 1-800-4-

DeWALT

forassistance.

The following conditions could lead to a weakening of the air tank,

and result in a violent air tank explosion:

English

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain

condensed water from

air tank, causing rust

and thinning of the steel

air tank.

• Drain air tank daily or after

each use. If air tank develops

a leak, replace it immediately

with a new air tank or replace

the entire compressor.

• Modifications or attempted

repairs to the air tank. • Never drill into, weld, or make

any modifications to the

air tank or its attachments.

Never attempt to repair a

damaged or leaking air tank.

Replace with a new air tank.

• Unauthorized modifications

to the safety valve or any

other components which

control air tank pressure.

• The air tank is designed

to withstand specific

operating pressures.

Never make adjustments

or parts substitutions

to alter the factory set

operating pressures.

Attachments & accessories:

• Exceeding the pressure

rating of air tools, spray

guns, air operated

accessories, tires, and

other inflatables can cause

them to explode or fly

apart, and could result in

serious injury.

• Follow the equipment

manufacturers

recommendation and never

exceed the maximum

allowable pressure rating

of attachments. Never use

compressor to inflate small

low pressure objects such

as children’s toys, footballs,

basketballs, etc.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your air compressor is

Like any other electrically

powered device, If it is not

used properly it may cause

electricshock.

• Never operate the

compressor outdoors when it

is raining or in wetconditions.

• Never operate compressor

with protective covers

removed ordamaged.

• Repairs attempted by

unqualied personnel can

result in serious injury or

death byelectrocution.

• Any electrical wiring or

repairs required on this

product should be performed

by a

DeWALT

factory

service center or a

DeWALT

authorized service center in

accordance with national and

local electricalcodes.

• Electrical Grounding:

Failure to provide

adequate grounding to

this product could result

in serious injury or death

from electrocution. See

Grounding Instructions

underInstallation.

• Make certain that the

electrical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage

and adequate fuseprotection.

English

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air

stream can cause soft

tissue damage to exposed

skin and can propel dirt,

chips, loose particles,

and small objects at high

speed, resulting in property

damage or personal injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people

or animals.

• Always turn the compressor

off and bleed pressure

from the air hose and air

tank before attempting

maintenance, attaching tools

or accessories.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal

such as the compressor

head, engine head, engine

exhaust or outlet tubes,

can result in serious burns.

• Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor

will remain hot for several

minutes after operation.

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Moving parts such as the

pulley, flywheel, and belt

can cause serious injury if

they come into contact with

you or your clothing.

• Never operate the compressor

with guards or covers which

are damaged or removed.

• Keep your hair, clothing, and

gloves away from moving

parts. Loose clothes, jewelry,

or long hair can be caught in

moving parts.

• Air vents may cover moving

parts and should be avoided

as well.

English

• Attempting to operate

compressor with damaged

or missing parts or

attempting to repair

compressor with protective

shrouds removed can

expose you to moving

parts and can result in

serious injury.

• Any repairs required on this

product should be performed

by a

DeWALT

factory

service center or a

DeWALT

authorized service center.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe operation of your

air compressor could lead

to serious injury or death to

you or others.

• Review and understand all

instructions and warnings in

this manual.

• Become familiar with the

operation and controls of the

air compressor.

• Keep operating area

clear of all persons, pets,

and obstacles.

• Keep children away from the

air compressor at all times.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea-

tures of this product.

• Equip area of operation with

a fire extinguisher.

• Do not operate machine with

missing, broken, or unautho-

rized parts.

WARNING: RISK OF FALLING

WHAT CAN HAPPEN HOW TO PREVENT IT

• A portable compressor

can fall from a table,

workbench, or roof causing

damage to the compressor

and could result in

serious injury or death to

the operator.

• Always operate compressor

in a stable secure position to

prevent accidental movement

of the unit. Never operate

compressor on a roof or

other elevated position. Use

additional air hose to reach

high locations.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and

duration of use, noise from

this product may contribute

to hearing loss.

• Always wear certied safety

equipment: ANSI S12.6

(S3.19) hearingprotection.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

English

FEATURES (Fig. 1)

ON/OFF SWITCH

Place this switch (A) in the ON position to G

provide automatic power to the pressure

switch and OFF to remove power at the

end of each use.

PRESSURE SWITCH

The pressure switch (J) automatically

starts the motor when the air tank

pressure drops below the factory set cut-

in pressure. It stops the motor when the air tank pressure reaches

the factory set cut-out pressure.

PRESSURE RELEASE VALVE

The pressure release valve located on the side of the pressure

switch, is designed to automatically release compressed air from

the compressor head and the outlet tube when the air compressor

reaches cut-out pressure or is shut off. The pressure release valve

allows the motor to restart freely. When the motor stops running,

air will be heard escaping from this valve for a few seconds. No air

should be heard leaking when the motor is running or after the unit

reaches cut-out pressure.

SAFETY VALVE

If the pressure switch does not shut off the air compressor at its cut-

out pressure setting, the safety valve (G) will protect against high

pressure by popping out at its factory set pressure (slightly higher

than the pressure switch cut-out setting).

CHECK VALVE

When the air compressor is operating, the check

valve (F) is open, allowing compressed air to enter

the air tank. When the air compressor reaches cut-

out pressure, the check valve closes, allowing air

pressure to remain inside the air tank.

TANK PRESSURE GAUGE

The tank pressure gauge (B) indi- DC

cates the reserve air pressure in

the tank.

OUTLET PRESSURE GAUGE

The outlet pressure gauge (C)

indicates the air pressure available

at the outlet side of the regulator. This pressure is controlled by the

regulator and is always less than or equal to the tank pressure.

REGULATOR

The regulator (D) controls the air pressure shown on the outlet

pressure gauge. Turn regulator knob clockwise to increase pressure

and counterclockwise to decrease pressure.

UNIVERSAL QUICK CONNECT BODIES (IF EQUIPPED)

The universal quick connect body (E) accepts the three most

popular styles of quick connect plugs: Industrial, automotive, and

ARO. One hand push-to-connect operation makes connections

simple and easy. The two quick connect bodies allow the use of two

tools at the same time.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels DeWalt Compresseur d'air

DeWalt

DeWalt D55270T Manuel utilisateur

DeWalt

DeWalt D55167-CA Manuel utilisateur

DeWalt

DeWalt Emglo D55155 Manuel utilisateur

DeWalt

DeWalt DXCMH1608WB Manuel utilisateur

DeWalt

DeWalt D55250 Manuel utilisateur

DeWalt

DeWalt DXCMH1608WB Manuel utilisateur

DeWalt

DeWalt DXCMV7518075 Manuel utilisateur

DeWalt

DeWalt DXCMTA1980854 Manuel utilisateur

DeWalt

DeWalt D55154 Manuel utilisateur

DeWalt

DeWalt Contractor's Electric Wheeled Portable Air Compressor... Manuel utilisateur

DeWalt

DeWalt D55168 Manuel utilisateur

DeWalt

DeWalt D55166 Manuel utilisateur

DeWalt

DeWalt DCC1054N-XJ Manuel utilisateur

DeWalt

DeWalt DXCMWA5591056-CA Manuel utilisateur

DeWalt

DeWalt D55394 Manuel utilisateur

DeWalt

DeWalt D55141 Manuel utilisateur

DeWalt

DeWalt Emglo D55150 Manuel utilisateur

DeWalt

DeWalt D55166 Manuel utilisateur

DeWalt

DeWalt DXCM301 Manuel utilisateur

DeWalt

DeWalt DXCMLA1682066 Manuel utilisateur

DeWalt

DeWalt D55371 Manuel utilisateur

DeWalt

DeWalt D55140 Manuel utilisateur

DeWalt

DeWalt D55168 Manuel utilisateur

DeWalt

DeWalt DPC6MRC-QS Manuel utilisateur

Manuels Compresseur d'air populaires d'autres marques

Sparmax

Sparmax DC-25XR Manuel utilisateur

KAESER

KAESER M122 Manuel utilisateur

GMC

GMC GAC1500 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton Air Compressor Manuel utilisateur

Fini

Fini F3GST2TK Manuel utilisateur

Industrial Air

Industrial Air CP1580325 Manuel de programmation

Campbell Hausfeld

Campbell Hausfeld RP3300 Guide de démarrage rapide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuel utilisateur

Hitachi

Hitachi EC99S Manuel de l'opérateur

Parkside

Parkside PKO 270 A1 Manuel utilisateur

Sullair

Sullair 185 Manuel utilisateur

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuel utilisateur

Ferm

Ferm CRM1046 Manuel utilisateur

BE AC153 Manuel utilisateur

RIDGID

RIDGID OF25150A Manuel utilisateur

Johnson Controls

Johnson Controls QUANTUM LX Manuel

Sears

Sears Craftsman 919.167463 Manuel utilisateur

Ring Automotive

Ring Automotive RAC700 Manuel utilisateur