CYP CH-331H-TX Manuel utilisateur
CH-331H-TX
HDMI over IP Transmitter
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2018 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document are
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
• Please completely disconnect the power when the unit is not in
use to avoid wasting electricity.
VERSION HISTORY
REV. DATE SUMMARY OF CHANGE
VS1 2019/01/28 Final technical review
VS2 2019/01/31 Updated Section 1, 5
CONTENTS
1. Introduction......................................................1
2. Applications.....................................................1
3. Package Contents ..........................................1
4. System Requirements......................................2
5. Features............................................................2
6. Operation Controls and Functions.................3
6.1 Front Panel ................................................. 3
6.2 Rear Panel.................................................. 4
6.3 IR Cable Pinouts ........................................ 5
6.4 Serial Port Pinout and Defaults ................ 5
6.5 WebGUI Control ........................................ 6
6.5.1 System Tab........................................ 7
6.5.2 Video Wall Tab ............................... 10
6.5.3 Network Tab ................................... 14
6.5.4 Functions Tab ................................. 17
6.6 Telnet Control .......................................... 19
6.7 Telnet Commands................................... 20
6.7.1 System Commands........................ 20
6.7.2 Network Commands ..................... 21
6.7.3 Discovery Service Commands ..... 22
6.7.4 Transmitter Specic Commands .. 23
6.7.5 Serial Commands........................... 27
7. Connection Diagram ....................................29
8. Specications ................................................30
8.1 Basic Specications ................................ 30
8.2 Video Specications............................... 31
8.3 Audio Specications............................... 32
8.4 Cable Specications .............................. 33
9. Acronyms .......................................................34
1
1. INTRODUCTION
This unit is an HDMI over IP Transmitter that allows you to extend
HDMI signals using the TCP/IP protocol over regular Cat.5e network
cable. This extender supports the transmission of High-Denition
signals (up to 1080p@60Hz) with audio up to 100m on a single cable.
The transmission distance can be further extended (up to 100m per
segment) by using Gigabit Ethernet network switches, allowing the
user to cascade the system without signal loss or introducing delay.
This Transmitter also features bi-directional IR and RS-232 pass-through.
It is also possible to for this Transmitter to operate in multicast mode,
allowing you to send a single AV signal to a large number of Receivers
within the same local network with no additional bandwidth cost.
Additionally, that same multicast signal can be used to create large
multi-display video walls with amazing simplicity.
This Video over IP system is perfect for both residential and commercial
installation environments. Conguration information is provided via the
On-Screen Display (OSD) on connected (but unlinked) Receivers and
control is via WebGUI, Telnet, or the AV over IP Master Controller.
2. APPLICATIONS
• HDMI, IR, and RS-232 extension
• Hotel or convention center display multi-monitor broadcast
• Long distance data and video transmission via cascading
• Distributed video matrix system
• Distributed video wall system
3. PACKAGE CONTENTS
• 1×HDMI over IP Transmitter
• 1×5V/2.6A DC Power Adapter
• 1×3.5mm to IR Extender Cable
• 1×3.5mm to IR Blaster Cable
• 1×3.5mm to DE-9 Female Adapter Cable
• 1×Shockproof Feet (Set of 4)
• 1×Operation Manual
2
4. SYSTEM REQUIREMENTS
• HDMI source equipment such as a media player, video game
console, PC or set-top box.
• A compatible HDMI over IP Receiver is required.
• A Gigabit Ethernet network switch with jumbo frame support is
required for multi-endpoint extension. (8K jumbo frames are strongly
recommended.)
• A Gigabit Ethernet switch with “IGMP snooping” enabled is required
for multicast support.
• A managed Gigabit Ethernet switch with VLAN support is strongly
recommended.
Special Notes:
• Mostconsumer-graderoutersarenotabletohandlethehightrafc
rates generated by multicast mode, so using one as your VoIP
network switch is discouraged.
• AvoidmixingregularnetworktrafcwithVoIPtrafc.Ifphysically
separatingthenetworkisnotpossible,VoIPtrafcshouldreside
within its own subnet or VLAN.
5. FEATURES
• HDMI 1.4 and DVI 1.0 compliant
• HDCP 1.4 compliant
• 1 HDMI input
• Video, audio and control transmission over TCP/IP in Unicast (point-
to-point) or Multicast (single-to-many) modes
• Multi-monitor video wall support with 180° and 270° rotation options
• HDMI input supports resolutions up to 1080p@60Hz/WUXGA
• Supports pass-through of audio formats including LPCM 2.0/5.1/7.1,
Bitstream and HD Bitstream
• Supports IR and RS-232 bypass
• Unit can be controlled via WebGUI, Telnet, and the AV over IP
Master Controller
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER RESET MODE ISP ISP
LINK
ON OFF
2 31
1POWER LED: This LED will ash while the unit is powering on and will
illuminate solidly once it has nished booting and is ready for use.
LINK LED: If the unit has no network connection this LED will not
illuminate. While the unit is attempting to establish a connection
with a Receiver this LED will ash. When the unit has established a
stable connection with a Receiver this LED will illuminate solidly.
2RESET Pinhole: Press this recessed button with a paperclip tip to
reboot the unit.
Note: Settings will not be reset.
MODE Pinhole: Press this recessed button with a paperclip tip
momentarily to toggle the video data streaming method between
“Graphic” and “Video” modes. “Graphic” mode is optimized for
high-detail static displays and “Video” mode is optimized for full
motion video.
Note: Pressing and holding the MODE button while the unit is
powered on will perform a full factory reset on the unit. Once the
resetiscomplete,bothLEDswillashrapidlyandtheunitmustthen
be manually power cycled.
ISP Pinhole: For factory use only.
3ISP Switch: For factory use only. For normal operation, this switch
should be set to “OFF”.
4
6.2 Rear Panel
RS-232 IN
IR
OUT HDMI IN
DC 5V
LAN
1 12 4 5 63
1DC 5V Port: Plug the 5V DC power adapter into this port and
connect it to an AC wall outlet for power.
2LAN Port: Connect to a Gigabit Ethernet switch for signal extension
to compatible Receiver(s), and to allow WebGUI/Telnet control.
3RS-232 Port: Connect to a PC, laptop, or serial controllable device
for the extension of RS-232 signals. The baud rate is congurable,
but the default baud rate is 115200.
Note: When a Transmitter is in multicast mode, every connected
Receiver unit will send RS-232 commands to that Transmitter
and commands sent from the Transmitter side will be sent to all
associated Receivers.
4IR IN Port: Connect to an IR Extender to receive IR control signals
and extend them to devices connected to a Receiver on the
same broadcast channel. Ensure that the remote being used is
within direct line-of-sight of the IR Extender.
Note: When the Transmitter is in multicast mode the IR signal is sent
to all associated Receivers.
5IR OUT Port: Connect to the provided IR Blaster to transmit IR signals
from a Receiver on the same broadcast channel to devices within
direct line-of-sight of the IR Blaster.
6HDMI IN Port: Connect to HDMI source equipment such as a media
player, game console or set-top box.
5
6.3 IR Cable Pinouts
IR Blaster
Cabl
e
1
2
3
Infrared
Power
Not U
sed
IR Extender
Cabl
e
1
2
3
Infr
ared
Power
Ground
6.4 Serial Port Pinout and Defaults
3.5mm to DE-9
A
dapter Cable
RxD
TxD
GND
1
2
3
Serial Port Default Settings
Baud Rate 115200
Data Bits 8
Parity Bits None
Stop Bits 1
Flow Control None
Table des matières
Autres manuels CYP Émetteur
CYP
CYP CH-2606TX Manuel utilisateur
CYP
CYP CH-1529TXV Manuel utilisateur
CYP
CYP CH-527TXVBD Manuel utilisateur
CYP
CYP PUV-1830TX-AVLC Manuel utilisateur
CYP
CYP CH-1602RX Manuel utilisateur
CYP
CYP CH-352TX Manuel utilisateur
CYP
CYP AVX-101F-TX Manuel utilisateur
CYP
CYP CH-507TX Manuel utilisateur
CYP
CYP PUV-3090TX-UEA Manuel utilisateur
CYP
CYP Dante AU-DTI4-TX Manuel utilisateur
CYP
CYP VEX-X1102T-B0C Manuel utilisateur
CYP
CYP CSI-8H8CV2IR Manuel utilisateur
CYP
CYP CH-506RXWP Manuel utilisateur
CYP
CYP CH-527TXPLVBD Manuel utilisateur
CYP
CYP PUV-3050TX-UA Manuel utilisateur
CYP
CYP CH-1107 TX Manuel utilisateur
CYP
CYP PU-607BD-TX Manuel utilisateur
CYP
CYP PU-1109 Manuel utilisateur
CYP
CYP PU-507TX-1H Manuel utilisateur
CYP
CYP CDPS-P313RTX Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
