CYP CH-2605TXV Manuel utilisateur
CH-2605TXV
4K UHD+ HDMI over HDBaseT 2.0 Transmitter (PD)
with HDR/ARC
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2018 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document are
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
• Please completely disconnect the power when the unit is not in
use to avoid wasting electricity.
VERSION HISTORY
REV. DATE SUMMARY OF CHANGE
VS1 2018/12/20 Final technical review
CONTENTS
1. Introduction......................................................1
2. Applications.....................................................1
3. Package Contents ..........................................2
4. System Requirements......................................2
5. Features............................................................2
6. Operation Controls and Functions.................4
6.1 Front Panel ................................................. 4
6.2 Rear Panel.................................................. 5
6.3 IR Cable Pinouts ........................................ 6
6.4 RS-232 Bypass Pinout................................. 6
6.5 Serial Control (Via USB Port) ..................... 6
6.6 Serial Commands (Via USB Port) ............. 7
7. Connection Diagram ......................................8
8. Specications ..................................................9
8.1 Technical Specications .......................... 9
8.2 Video Specications............................... 10
8.3 Audio Specications............................... 11
8.4 Cable Specications .............................. 12
8.5 HDBaseT Features.................................... 13
9. Acronyms .......................................................13
1
1. INTRODUCTION
This HDBaseT 2.0 Transmitter provides for the extension of 4K video
with HDR and high bitrate audio over a single Cat.6a/7 cable at
distances of up to 100m (328 feet). This Transmitter complies with the
advanced HDCP 2.2 and HDMI 2.0 standards, as well as supporting
the legacy HDCP 1.x and HDMI 1.x standards. Despite HDBaseT’s
10.2Gbps bandwidth limitation, 4K UHD HDMI video sources, up to and
including 4K@60Hz (4:4:4, 8-bit) as well as 10/12-bit sources with HDR,
are able to be processed and extended by the use of AVLC (Adaptive
Visually Lossless Compression) when connected to a compatible
AVLC Receiver. This Transmitter can also pass RS-232, IR, Ethernet, and
multiple audio streams across the same cable that carries the video
signal.
The bi-directional optical audio feature allows optical audio to be
exchanged bi-directionally between the Transmitter and Receiver.
Rounding out the feature set is automatic HDBaseT clock stretching
and TMDS re-clocking support. This Transmitter is powered directly
by the connected Receiver, via 48V PoH (Power over HDBaseT),
eliminating the need for a separate power supply for the Transmitter.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
2
3. PACKAGE CONTENTS
• 1×HDMI over HDBaseT 2.0 Transmitter (PD) with HDR/ARC
• 1×3.5mm to IR Blaster Cable
• 1×Shockproof Feet (Set of 4)
• 1×Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI source equipment such as a media player, video game
console or set-top box.
• A compatible HDBaseT Receiver with 48V PoH (PSE) support is
required.
• An HDBaseT 2.0 Receiver equipped with AVLC support is strongly
recommended.
• The use of “Premium High Speed” HDMI cables, and industry
standard Cat.6, Cat.6a or Cat.7, is highly recommended.
5. FEATURES
• HDMI with HDR, 3D & 4K@60Hz support, DVI 1.0 compatible
• HDCP 2.2 and HDCP 1.x compliant
• Supports up to 4K UHD (18Gbps, 4K@50/60Hz 4:4:4, 8-bit) video input
and output
• Supports Deep Color input and output up to 12-bit
• Supports 10-bit and 12-bit HDR (High Dynamic Range) input/output
• Supports CEC bypass
• HDBaseT output transmits video, audio and data over a single
Cat.5e/6/7 cable and can reach distances up to 100m/328ft at 4K
when using Cat.6a/7
• HDBaseT feature support: HD Video and Audio, 100BaseT Ethernet,
48V PoH (PD), bi-directional optical audio and Control (bi-directional
IR/RS-232 pass-through)
• Integrated AVLC (Adaptive Visually Lossless Compression) activates
when the bandwidth requirements of the source are beyond
10.2Gbps (340MHz) allowing for sources up to 18Gbps (600MHz) to
3
be sent to a compatible Receiver with no loss of visual quality
• The AVLC feature allows manual selection between High Quality
Mode (Full bandwidth) and Standard Mode (Lower bandwidth,
useful for longer cable runs with 4K sources)
• Bi-directional optical audio extension support
• Supports HDMI DDC bus clock stretching for improved compatibility
with certain Blu-ray players
• Performs TMDS re-clocking and signal re-generation for improved
signal integrity
• Powered via 48V PoH from Receiver to Transmitter
Note: A compatible PSE Receiver providing 48V PoH is required to
power this Transmitter. Receivers from other brands may not be
compatible.
4
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
SERVICE ARC
OPT
HQ
STD
POWER
LINK
HQ/STD
SWITCH
1 2 3 4 5
1SERVICE Port: This port is reserved for rmware update and serial
control use only.
2ARC & OPT LEDs: These LEDs illuminate to indicate if the optical
output source is coming from the optical input or ARC on the
connected Receiver.
Note: Selecting ARC as a source requires a compatible Receiver.
3HQ/STD SWITCH Button: This switch allows the user to select which
compression mode to use when AVLC is required. A single press
toggles between modes.
HQ (High Quality) mode uses the least amount of compression and
provides the highest possible visual quality (perceptually identical
to the original). In this mode, AVLC compression activates for any
signal requiring more than 9Gbps.
STD (Standard Quality) mode applies additional signal reduction
methods to lower the bandwidth requirements even further,
improving transmission reliability at the cost of some visual delity.
In this mode, AVLC compression activates for any signal requiring
more than 7.5Gbps.
4HQ/STD LEDs: These LEDs illuminate to indicate which AVLC mode
is selected: HQ (High Quality) or STD (Standard Quality).
5POWER LED: This LED will illuminate to indicate the unit is on and
receiving power.
Note: A compatible 48V PSE Receiver is required to power this
Transmitter.
LINK LED: This LED will illuminate solidly when a live connection with
a compatible Receiver is active.
5
6.2 Rear Panel
LANHDMI ININOUT
RS-232
BYPASS
IR OPTICAL
CAT5e/6/7 OUTOUT IN
1 2 3 4 5 6
1RS-232 BYPASS Port: Connect to a PC, laptop or serial controllable
device for the extension of RS-232 signals between both ends of
the HDBaseT connection.
2IR OUT Port: Connect to the provided IR Blaster to transmit IR signals
from the other end of the HDBaseT connection to devices within
direct line-of-sight of the IR Blaster.
IR IN Port: Connect to an IR Extender to extend the IR control
range of devices connected to the other end of the HDBaseT
connection. Ensure that the remote being used is within direct line-
of-sight of the IR Extender.
3OPTICAL OUT Port: Connect to powered speakers or an amplier
for digital audio output using an appropriate optical cable. The
audio is sourced from either the Optical Audio Input port or ARC of
a connected compatible Receiver.
OPTICAL IN Port: Connect to the optical audio output of a device
such as a media player or game console using an appropriate
optical cable. Audio is sent to the Optical Audio Output on a
connected compatible Receiver.
4CAT5e/6/7 OUT Port: Connect to a compatible HDBaseT Receiver
with a single Cat.5e/6/7 cable for transmission of all data signals.
48V PoH will also be supplied when connected to a compatible
PSE Receiver.
5HDMI IN Port: Connect to HDMI source equipment such as a media
player, game console or set-top box.
6LAN Port: Connect to an Ethernet supporting device or to your
local network, as appropriate, to extend the network to both ends
of the HDBaseT connection.
Table des matières
Autres manuels CYP Émetteur
CYP
CYP CH-2538TXM-TB Manuel utilisateur
CYP
CYP PUV-1510RXWP Manuel utilisateur
CYP
CYP CH-507TXBD: CH-507RXBD Manuel utilisateur
CYP
CYP CH-306TXA & RXA Manuel utilisateur
CYP
CYP CH-506RXWP Manuel utilisateur
CYP
CYP CH-1605TXV Manuel utilisateur
CYP
CYP CH-507TX Manuel utilisateur
CYP
CYP PU-507-KIT Manuel utilisateur
CYP
CYP PUV-1620S-TX Manuel utilisateur
CYP
CYP PU-103 Manuel utilisateur
CYP
CYP CH-U331TX Manuel utilisateur
CYP
CYP CA-HDMIAT Manuel utilisateur
CYP
CYP CH-1107 TX Manuel utilisateur
CYP
CYP PU-515PLTX-1H Manuel utilisateur
CYP
CYP DCT-30TX Manuel utilisateur
CYP
CYP CH-2527TX Manuel utilisateur
CYP
CYP CH-1527TXPLV Manuel utilisateur
CYP
CYP Dante AU-DTI4-TX Manuel utilisateur
CYP
CYP PU-514LTX-1H Manuel utilisateur
CYP
CYP PU-507TX-CVGA Manuel d'installation
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
