CYP CH-1602RX Manuel utilisateur

CH-1602TX & CH-1602RX

HDMI over HDBaseT Transmitter and Receiver

with Optical Audio Return (OAR)

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE

VR0 08/06/15 Preliminary release

VR1 24/06/15 Connection Diagram

VR2 03/07/15 Connection Diagram

VS3 22/03/17 Updated text/diagrams

CONTENTS

1. Introduction......................................................1

2. Applications.....................................................1

3. Package Contents ..........................................1

4. System Requirements......................................2

5. Features............................................................2

6. Operation Controls and Functions.................3

6.1 Transmitter's Front Panel ........................... 3

6.2 Transmitter's Side Panels ........................... 4

6.3 Receiver's Front Panel............................... 5

6.4 Receiver's Side Panels .............................. 6

6.5 IR Cable Pin Assignment........................... 7

7. Connection Diagram ......................................8

8. Specications ..................................................9

9. Acronyms .......................................................10

1. INTRODUCTION

This HDBaseT 2.0 Transmitter and Receiver set can send uncompressed

UHD video and audio over a single Cat.5e/6/7 cable up to 100m.

It has the added benet of extending control and communication

signals through the built-in Ethernet, USB, RS-232 and IR ports.

Independent external digital and analog audio transmission capability

gives users the extra convenience of additional audio connections.

This system supports connecting any standard USB 2.0 host to the

Transmitter, enabling the extension of the USB connection to up to 2

USB ports located on the Receiver, allowing it to act like a USB hub.

The integrated 48V PoH (Power over HDBaseT) support provides

power to the Receiver (PD) from the Transmitter (PSE), eliminating

the need for a separate power supply for the Receiver. The ultra-thin

mechanical design allows for exibility in mounting locations, saving

space and making your presentation space orderly and tidy.

2. APPLICATIONS

• Home theater extension and control

• Lecture hall display and control

• Showroom display and control

• Meeting room presentation and control

• Classroom display and control

3. PACKAGE CONTENTS

• 1×HDMI over HDBaseT Transmitter

• 1×HDMI over HDBaseT Receiver

• 1×IR Extender Cable

• 1×IR Blaster Cable

• 4×Terminal Blocks (3-pin)

• 1×48V/0.83A Power Adaptor

• 1×Power Cord

• 2×Rack Mount Ears (Set of 2)

• 1×Operation Manual

4. SYSTEM REQUIREMENTS

• HDMI input source equipment such as media players, video game

consoles, PCs or set-top boxes.

• HDMI receiving equipment such as HDTVs, monitors or audio

ampliers.

• The use of “Premium High Speed HDMI” cables is highly

recommended.

• High quality Cat.5e/6/7 cables (Cat.6 or better is recommended).

5. FEATURES

• Supports the HDBaseT 2.0 specication over a single Cat.6/7 cable

up to 100m/328ft and Cat.5e cable up to 90m/295ft

• HDBaseT 5Play™ convergence: High-Denition (HD) Video and

Audio, 100BaseT Ethernet, 48V PoH, and Control (Bi-directional IR/

RS-232 pass-through)

• Receiver (PD) is powered by 48V PoH from the transmitter (PSE)

• HDMI with 3D & 4K@60Hz (YUV 4:2:0) support, DVI 1.0 compatible

• HDCP 2.2 compliant

• 1×USB 2.0 Mini-B port (on the transmitter), 2×USB 2.0 Type A ports (on

the receiver)

• Supports pass-through of HD audio formats: LPCM 2.0/5.1/7.1,

Bitstream, and HD Bitstream

• Supports optical audio sampling rates up to 48kHz

• Supports external analog and digital audio extension including

support for ARC (Audio Return Channel)

• Supports RS-232 baud rates from 110~115200bps

• Ultra-thin mechanical design

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Transmitter's Front Panel

TX RX



DC 48VPOWER AUDIO IN IR IN2 IR OUT1 USB UPDATERS-232 IN

CAT5e/6/7 OUT

HDMI IN

OPT.

OUTLAN

ARC OUT

OFFON

1 2 3 4 5 6 7

1DC 48V & POWER LED: Plug the 48V DC power adapter into this

port and connect it to an AC wall outlet for power. The LED will

illuminate to indicate the unit is on and receiving power.

2AUDIO IN: Connect to the stereo analog output of a device such

as a CD player or PC to extend it to the Receiver’s AUDIO OUT L/R

port.

3IR IN 2: Connect to the provided IR Extender to extend the IR

control range of remotely located devices. Ensure that the remote

being used is within direct line-of-sight of the IR Extender.

4IR OUT 1: Connect to the provided IR Blaster to transmit IR signals to

devices within direct line-of-sight of the IR Blaster.

5USB: Connect to a PC or Laptop to extend the USB data

connection to the Receiver’s USB ports.

6RS-232 IN: Connect to a PC, laptop or other serial control device

with a 3-pin adapter cable for the extension of RS-232 signals to

the Receiver. When receiving commands from the Receiver side,

depending on your equipment’s pinout, the Tx and Rx pins might

need to be reversed.

7UPDATE: This is reserved for rmware update use only. During

normal operation the dipswitch should be set to the right.

6.2 Transmitter's Side Panels

TX RX



DC 48VPOWER AUDIO IN IR IN2IR OUT1 USBUPDATERS-232 IN

CAT5e/6/7 OUT

HDMI IN

OPT.

OUTLAN

ARC OUT

OFFON

TX RX



DC 48VPOWER AUDIO IN IR IN2IR OUT1 USBUPDATERS-232 IN

CAT5e/6/7 OUT

HDMI IN

OPT.

OUTLAN

ARC OUT

OFFON

1 2 3 4 5

1LAN: Connect to an Ethernet supporting device or to your local

network as appropriate. The yellow LED will illuminate to indicate a

successful LAN connection between the Transmitter and Receiver

and will blink to indicate a data transmission. The green LED will

illuminate when the connected Ethernet speed is 100Mbit/s.

2OPT. OUT: Connect to an audio receiver or powered speaker set to

reproduce the audio signal from the Receiver’s OPT. IN port.

3ARC OUT ON/OFF: Enables or disables support for ARC (Audio

Return Channel) signals from the HDMI device connected to the

Receiver. When switched to ON the ARC audio will be routed to

both the HDMI input as well as the OPT. OUT port. When switched

OFF no ARC audio will be passed.

Note: When ARC is enabled the maximum supported HDMI cable

length may vary. It is suggested to use cables under 2 meters long

to ensure the best audio quality.

4HDMI IN: Connect to HDMI source equipment such as a media

player, game console or set-top box.

5CAT5e/6/7 OUT: Connect to the Receiver unit with a single

Cat.5e/6/7 cable for transmission of all data signals. The yellow LED

will illuminate to indicate a successful data connection between

the Transmitter and Receiver. If the yellow LED blinks irregularly it

indicates a data link error. The green LED will illuminate to indicate

when PoH is active.

6.3 Receiver's Front Panel

TX RXLR



OPT.

POWER AUDIO OUT IR IN1 IR OUT2 USB USB UPDATERS-232 OUT

CAT5e/6/7 IN

HDMI OUTLAN

OPT.

ARC

1 2 3 4 5 6 7

1POWER LED: This LED will illuminate when the device is receiving

power.

2AUDIO OUT: Connect to powered speakers or an amplier for

stereo analog audio output.

3IR IN 1: Connect to the provided IR Extender to extend the IR

control range of remotely located devices. Ensure that the remote

being used is within direct line-of-sight of the IR Extender.

4IR OUT 2: Connect to the provided IR Blaster to transmit IR signals to

devices within direct line-of-sight of the IR Blaster.

5USB: Connect to USB peripheral devices such as keyboard,

mouse, printer, ash drive, etc. for connection with the USB device

connected to the Transmitter.

6RS-232 OUT: Connect to the device you wish to control via a 3-pin

adapter cable to receive RS-232 commands from the Transmitter.

When sending commands to the Transmitter side, depending on

your equipment’s pinout, the Tx and Rx pins might need to be

reversed.

7UPDATE: This is reserved for rmware update use only. During

normal operation the dipswitch should be set to the right.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels CYP Émetteur

CYP

CYP PUV-1510TX Manuel utilisateur

CYP

CYP PU-8H8CTXIR Manuel utilisateur

CYP

CYP AVX-101F-TX Manuel utilisateur

CYP

CYP CH-103TX Manuel utilisateur

CYP

CYP CH-306TXA & RXA Manuel utilisateur

CYP

CYP CH-507TXWPUS Manuel utilisateur

CYP

CYP CH-506RXWP Manuel utilisateur

CYP

CYP COH-RX2 Manuel d'installation

CYP

CYP CH-2538TXM-TB Manuel utilisateur

CYP

CYP CH-507TX Manuel utilisateur

CYP

CYP PU-501 Manuel utilisateur

CYP

CYP CH-507TXBD: CH-507RXBD Manuel utilisateur

CYP

CYP DCT-30TX Manuel utilisateur

CYP

CYP CH-2606TX Manuel utilisateur

CYP

CYP CH-2605TXV Manuel utilisateur

CYP

CYP PUV-1660TTX Manuel utilisateur

CYP

CYP PU-507TX-CVGA Manuel d'installation

CYP

CYP CH-2602TXWPUS Manuel utilisateur

CYP

CYP CH-2527TXPL Manuel utilisateur

CYP

CYP CH-507TX Manuel utilisateur

CYP

CYP CH-331H-TX Manuel utilisateur

CYP

CYP PUV-1210PL-TX Manuel utilisateur

CYP

CYP PU-515PLTX-1H Manuel utilisateur

CYP

CYP CH-516TXAS Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur