CommScope TC-96370-IP Manuel utilisateur

12 Port Single Fiber Splice Cassette for

Propel Panel

PROPEL

PRODUCT PAGE

QR CODE

Prepare cable for single fiber splice cassette installation

Group feeder fibers into two groups (1-12 and 13-24), then refer to Table 1 for

Feeder and Pigtail Lengths. “Feeder Strip Length” is the recommended length

of fiber to bring into the cassette. “Feeder Cut Length” and “Pigtail Cut Length”

is measured from the front of the cassette and is the recommended cut length

for the initial splice. A maximum of (1) rework is allowed per splice.

Route fibers into base

(a) Position spools to prepare for routing. (b) Route pigtail and feeder fibers

corresponding to fibers 1-12 counterclockwise starting along the outer half of

the cassette and work inwards with each consecutive loop. (c) Line up the pegs

on the cassette base with the mounting holes on the spool to finish routing.

(d) Insert spool into base and ensure all fibers are under retaining fingers.

(e) Position spool of fiber 13-24 as shown to prepare for routing. Ensure fibers

are tucked under retaining feature (f) Repeat steps a-d until routing is completed.

Apply Cover

(a) Line the cover with the slots near the front of the cassette base. (b) Lay

the cover flat on the base and ensure all the tabs on the side of the cover

and bases are lined up. With one hand holding the cassette base, push cover

forward with other hand to engage tabs. Double check the rear tab is

also engaged to prevent the cover from sliding off.

Table 1: Pigtail and Feeder Lengths

12 Port Cassette, shown above

Tools and Materials Required

FIBER FUSION SPLICER

AND CLEAVER

STRIPPER

FIBER SCISSORS

SMALL SIDE CUTTER

TAPE

MEASURE

MARKER

TAPE

ISOPROPYL

ALCOHOL INCLUDED:

SPLICE PROTECTORS

(40 mm LONG)

and CABLE TIES

(30 - 40 mm LONG)

Page 1 of 4Page 4 of 4

Quick

Start

TC-96370-IP · Rev B · August, 2023

Strength Member

Splice

Protectors

Feeder

Pigtail

Feeder

Prepare to place feeder

fiber in cassette

Using thumb & finger, disengage

rear tab by lifting and pulling

backward to remove the cover.

Remove cassette cover Measure and trim pigtail and feeder

Install feeder fiber in splice cassette

http://www.commscope.comhttp://www.commscope.com

(a) Strip fibers to recommended Feeder Strip length per table 1. Leave

approximately 1” (2.5 cm) of strength member. Secure cable tie around fiber

strength member. (b) Optional: Wrap smaller diameter cable with provided grey

foam for better securement. (c) Snip off ends of cable ties close to head.

(d) Push the head downward until it is below the top of the cassette wall.

(If using a 24f cable, separate fibers 1-12 and 13-24. Then use one tie-off

location at the cassette entry point.)

(a) Remove spool and splice

holder from cassette. Locate

ends of pigtail marked with tape.

(b) Unspool and extend pigtail

fiber beyond front of cassette.

Extend feeder fibers beyond the front of the cassette base, then measure and

trim pigtail and feeder to specified cut length per Table 1.

Install splice protectors

on all fibers to be spliced

Use provided splice protectors.

Splice protector length should be

45mm maximum.

Splice feeder and pigtail

fibers

Strip, clean, and splice fibers

following recommened method.

Preparing to load splice

protectors

Locate “P” and “F” marking on

spool. When loading splice

protectors, ensure pigtail is exiting

spool through the side with “P”

marking and the feeder is exiting

through the side with “F” marking.

bLoad splice protectors

into splice holder

(a) Load splice protectors into

splice holder (b) Utilizing the spool

fiber retainers, route pigtail fibers

counterclockwise until feeder and

pigtail fibers converges.

Page 2 of 4 Page 3 of 429004-A

Autres manuels CommScope Matériel réseau

CommScope

CommScope SCIL-B Manuel utilisateur

CommScope

CommScope ONECELL RP5200 Manuel

CommScope

CommScope SYSTIMAX 100BASE-T Manuel utilisateur

CommScope

CommScope ION-M7P Manuel utilisateur

CommScope

CommScope FOSC-OC-6 Manuel utilisateur

CommScope

CommScope NETCONNECT 1479542-1 Manuel utilisateur

CommScope

CommScope SYSTIMAX EHD Manuel utilisateur

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuel utilisateur

CommScope

CommScope ION-M17EHP/19P Manuel utilisateur

CommScope

CommScope UNJ10G Manuel utilisateur

CommScope

CommScope ION-M7P Manuel utilisateur

CommScope

CommScope OneCell RP5000 Series Mode d’emploi

CommScope

CommScope NOVUX DSC 650 Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope M3200 Manuel utilisateur

CommScope

CommScope ION-M23 SDARS Manuel utilisateur

CommScope

CommScope WCS-2 Manuel utilisateur

CommScope

CommScope FDC-W8-FAT Manuel utilisateur

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Manuel utilisateur

CommScope

CommScope SYSTIMAX AirSPEED AP542 Manuel utilisateur

CommScope

CommScope EHD Manuel utilisateur

CommScope

CommScope CPPR-QF-F-1U-E Manuel utilisateur

CommScope

CommScope AMP NETCONNECT MRJ21 Manuel utilisateur

CommScope

CommScope RUCKUS SmartZone 100 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur