CommScope SYSTIMAX EHD Manuel utilisateur

660000222 Rev B Page 1

User Manual

INTRODUCTION ............................................................................. 2

Revision History........................................................................ 2

Trademark Information ................................................................... 2

Applicable Standards .................................................................... 2

Admonishments ........................................................................ 3

General Safety Precautions ................................................................ 3

1 PRODUCT DESCRIPTION .................................................................. 3

1.1 General Description ............................................................... 3

1.2 Major Components ................................................................ 3

1.3 Specifications ................................................................... 5

2 UNPACKING AND INSPECTION .............................................................. 5

3 UNPACKING A PANEL WITH A PRETERMINATED CABLE ............................................. 5

4 PANEL INSTALLATION ...................................................................13

(continued)

Content Page

26379-A

TECP-91-005

Rev E, October 2017 EHD

SYSTIMAX®Enhanced High Density (EHD) Panel

With Preterminated Cable

TECP-91-005 • Issue 5 • October 2017

Page 2

4.1 Overview ...................................................................... 13

4.2 Tools and Hardware Needed ......................................................... 13

4.3 Mounting an Unloaded Panel ........................................................ 13

4.4 Grounding the Panel .............................................................. 16

5 GENERAL CABLE REQUIREMENTS ........................................................... 18

6 OPERATION .......................................................................... 19

6.1 Sliding Out Blade to First Position ..................................................... 19

6.2 Accessing Connectors on Back of Adapter Pack ............................................ 19

6.3 Closing Blade ................................................................... 20

6.4 Removing Blade from Front ......................................................... 21

6.5 Removing Fiber Cover ............................................................. 22

6.6 Re-Installing Fiber Cover ........................................................... 22

7 TECHNICAL ASSISTANCE ................................................................. 23

INTRODUCTION

This user manual describes the SYSTIMAX Enhanced High Density (EHD) Panel,

Included in this user manual are all procedures required in installing the SYSTIMAX

EHD Panel as well as operation procedures.

Revision History

Trademark Information

CommScope (logo), CommScope, SYSTIMAX, and Enhanced High Density Panel are

trademarks

Applicable Standards

UL 60950-1, 2nd Edition, 2007-03-27 (Information Technology Equipment - Safety -

Part 1: General Requirements

CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03 (Information Technology Equipment

-Safety - Part 1: General Requirements)

ISSUE DATE REASON FOR CHANGE

1 9/2015 Original.

2 10/2015 Added minimum cable bend radius and maximum patch cord size.

3 3/2016 Added applicable standards and panel grounding instructions.

4 July 2016 Updated for front-access only design

E October 2017 Updated for product name change to SYSTIMAX.

TECP-91-005 • Issue 5 • October 2017

Page 3

Admonishments

Important safety admonishments are used throughout this manual to warn of possible

hazards to persons or equipment. The admonishments — in the form of Dangers,

Warnings, and Cautions — must be followed at all times.

General Safety Precautions

1 PRODUCT DESCRIPTION

1.1 General Description

The SYSTIMAX Enhanced High Density (EHD) Panel is a pre-terminated fiber optic

connector panel intended for use in large data centers in a direct connect or

interconnect environment. The SYSTIMAX EHD Panel mounts in a 19-inch (48.26 cm)

equipment rack with a 3-inch or 5-inch channel. In each 1RU of rack space, a fully

loaded panel provides 144 LC terminations using duplex LC adapters.

The SYSTIMAX EHD Panel is designed for ease of installation and access. It is

available with either left- or right-side cable entry. The panel features sliding blades

(three per 1RU of rack space), providing full access to adapters and connectors. Each

blade can accommodate four adapter packs. The SYSTIMAX EHD Panel is available

with either a black or sky white baked enamel exterior.

1.2 Major Components

Figure 1 shows the main components of the SYSTIMAX EHD Panel. They are as

follows:

Danger: Danger is used to indicate the presence of a hazard that will cause severe personal

injury, death, or substantial property damage if the hazard is not avoided.

Warning: Warning is used to indicate the presence of a hazard that can cause severe

personal injury, death, or substantial property damage if the hazard is not avoided.

Caution: Caution is used to indicate the presence of a hazard that will or can cause

minor personal injury or property damage if the hazard is not avoided.

Caution: When mounting equipment in the rack make sure mechanical loading is even

to avoid a hazardous condition, such as loading heavy equipment in the rack unevenly.

The rack should safely support the combined weight of all equipment it supports.

Caution: This equipment is to be installed only in Restricted Access Areas (dedicated

equipment rooms, equipment closets, etc.) in accordance with Articles 110-16, 110-17,

and 110-18 of the National Electrical Code, ANSI/NFPA 70.

TECP-91-005 • Issue 5 • October 2017

Page 4

•Blade—holds adapter packs or cabled modules; slides out to two front access

positions and is removable from front. There are three blades per RU rack space.

Figure 1. SYSTIMAX EHD Panel Main Components (2RU Model Shown)

•Fiber Cover—holds down fibers on each blade to prevent them from being

inadvertently snagged or misrouted.

•Grounding Location—is where a two-hole lug and ground wire are attached to

connect panel ground PEM nuts to office ground. A two-hole lug is provided with

the product; the ground wire is not.

•Mounting Brackets—can be flipped around to provide either front- or rear-facing

mounting on a channel rack.

•Front Door—swings down to provide access to the interior of the panel. The door

features a double hinged design that allows users to open the door without

interfering with equipment below the panel on the same rack, or also to allow the

door to lay flat for easy access to the bottom blade.

•Designation Label—provides physical space for recording fiber designations.

•Duplex LC Adapter Pack—(shown for reference) mounts within the blade.

Product offerings for adapter packs include LC adapter packs in singlemode APC

or UPC style.

Note: In this figure, the 2RU panel is shown. Main components are analogous for

other RU sizes.

26380-A

DUPLEX LC

ADAPTER PACK

(SHOWN FOR

REFERENCE)

MOUNTING

BRACKET (2X)

BLADE (6X)

(FULLY REMOVED

FROM CHASSIS)

DESIGNATION LABEL

FRONT

DOOR

GROUNDING

LOCATION

FIBER

COVER (2X)

TECP-91-005 • Issue 5 • October 2017

Page 5

1.3 Specifications

Table 1 lists specifications for the SYSTIMAX EHD Panel. Table 2 summarizes the

supported adapter packs and modules for the SYSTIMAX EHD Panel.

2 UNPACKING AND INSPECTION

1. Inspect the exterior of the shipping container(s) for evidence of rough handling

that may have damaged the components in the container.

2. Unpack each container while carefully checking the contents for damage and

verify with the packing slip.

3. If damage is found or parts are missing, file a claim with the commercial carrier

and notify CommScope Customer Service. Save the damaged cartons for

inspection by the carrier.

4. Refer to Topic 7 on Page 22 if you need to contact CommScope.

5. Save shipping containers for use if equipment requires shipment at a future date.

3 UNPACKING A PANEL WITH A PRETERMINATED CABLE

The pre-terminated panel is shipped with the panel mounted on top of a spool

containing the cable. The stub end of the cable is unwound to a splice vault or other

point of termination. To protect the panel and cable windings contained within the

upper cylinder of the shipping unit, It is critical to leave the foam packaging material

surrounding the panel in place until the unit has been transported to the final

installation location. Transporting the unit without the foam packaging in place may

result in damage to the panel and/or cable. To unpack and mount a fully loaded panel,

use the following procedure.

Table 1. SYSTIMAX EHD Panel Specifications

PARAMETER SPECIFICATION REMARKS

Operating conditions 14Fto +140F (10Cto +60C)

Humidity 10% to 95% RH No condensation

Storage conditions 40F to +158F (40C to

+70C)

Dimensions (2RU) D x W x H

(with mounting brackets) 19.64 in. (49.9 cm) D x 19.09 in.

(48.5 cm) W x 3.5 in. (6.04 cm) H Width without mounting brack-

ets: 17.27 in. (43.9 cm)

Weight per 2RU 23.4 lbs. (1.06 Kg)

Table 2. SYSTIMAX EHD Panel Supported Adapter Packs and Modules

DESCRIPTION

FRONT

CONNECTOR

TYPE

FRONT

PORT

COUNT

REAR CONNECTOR

TYPE

REAR

PORT

COUNT

FIBER

CONFIGURATION

LC Adapter Pack LC 24 LC 24 NA

TECP-91-005 • Issue 5 • October 2017

Page 6

1. Cut off the external plastic as shown in Figure 2.

Figure 2. Cutting Off External Plastic

2. Cut off the cardboard wrap on the cable spool as shown in.Figure 3.

Figure 3. Cutting Off Cardboard Wrap on Cable Spool

Note: Use caution when unpacking and installing the SYSTIMAX EHD Panel.

Avoid twisting cable and do not violate cable minimum bend radius.

Note: Use caution when removing packaging materials. Sharp utensils can

damage fiber optic cable.

TECP-91-005 • Issue 5 • October 2017

Page 7

3. Remove the four carousel locking screws shown in Figure 4 to unlock the

carousel, allowing the spool to rotate freely,

Figure 4. Carousel Locking Screws and Cable Stub

4. Pay out the cable stub as indicated by the red arrow in Figure 4, pulling cable end

to termination location.

5. Remove the four wing nuts shown in Figure 5.

Figure 5. Removing Wing Nuts

25873-A

CABLE STUB

CAROUSEL LOCKING

SCREWS (4X)

25874-A

REMOVE WING

NUTS (4X)

TECP-91-005 • Issue 5 • October 2017

Page 8

6. Lift off the top cover to expose the panel packaging as shown in Figure 6.

Figure 6. Lifting Off Top Cover

TECP-91-005 • Issue 5 • October 2017

Page 9

7. Remove the outer rim as shown in Figure 7.

Figure 7. Lifting Off Outer Rim

8. Remove and unpack the accessories contained in shipment carton shown on top

of the packaging foam in Figure 8.

TECP-91-005 • Issue 5 • October 2017

Page 10

Figure 8. Shipment Carton Containing Accessories

9. Remove and unpack the plastic wrapper containing the SYSTIMAX EHD Panel,

as shown in Figure 9.

Figure 9. SYSTIMAX EHD Panel in Plastic Wrapper

Table des matières

Autres manuels CommScope Matériel réseau

CommScope

CommScope Uniprise Solutions HFTP-HD6B-1U-24 Manuel utilisateur

CommScope

CommScope NOVUX SEC 100 Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope RUCKUS SmartZone 100 Manuel utilisateur

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Manuel utilisateur

CommScope

CommScope M3200 Manuel utilisateur

CommScope

CommScope SCIL-B Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope NETCONNECT 1479542-1 Manuel utilisateur

CommScope

CommScope AMP NETCONNECT MRJ21 Manuel utilisateur

CommScope

CommScope ION-U EU H 23/23 Manuel utilisateur

CommScope

CommScope Constellation CPT-PP-48C Manuel utilisateur

CommScope

CommScope SYSTIMAX AirSPEED AP542 Manuel utilisateur

CommScope

CommScope FOSC-OC-6 Manuel utilisateur

CommScope

CommScope UNJ10G Manuel utilisateur

CommScope

CommScope ION-M23 SDARS Manuel utilisateur

CommScope

CommScope ION-M7P Manuel utilisateur

CommScope

CommScope CPP-UDDM-SL-1U-24 Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope MRJ21 Quick Fit Cassette Manuel utilisateur

CommScope

CommScope LSX Manuel utilisateur

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuel utilisateur

CommScope

CommScope OneCell RP5000 Series Mode d’emploi

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur